| Subject | Text |
| Ilo PDP4210EA1 42" Plasma Black screen s-video to comp | Nice forum and after reading several post I'm getting closer but totally new at Plasma TV repair, so |
| :) Okay: lots of folks experience these type of problems after a move. and they do just what you did |
|
|
| Metz ch696G1 dead | Hi,
The set is totally dead. No light in standby led.
I've found some defective components and |
| Re: Accer 1916 w problems | [quote:fd75ec55c3="Jeremiahw"]I have acer 1916 w monitor that when it powers up it say input not acc |
| Hitachi TV | I also have the Hitachi C28W410SN. My TV resets it's self every time the picture format changes, or |
| Plasma | The noise is coming from the AC power supply capacitors. It sound as it is rapidly charging and dich |
| Re: Worked for me also. Great Job | [quote:33bb56492b="Damanvir"]Agatha,
Great Job my camera works well. After reading previous strin |
| Did you check the startup resistor, and small electro's in the P/S? |
| Try "Display + 5 + VOL UP + POWER" in sequence with the tv off. |
| Re: PSU | [quote:b7a424abd8="gilloz"]I am assuming that your PC does not go into the boot-up sequence when you |
| SA 410 Technic reveiver | Hi everybody
I have an old but very good SA 410 Technics receiver which was working well since last |
| The optocoupler is for voltage regulation. Have you tested the startup resistors? |
| Need help befor crazy | I need diagram for Nec multisynec E700
or someone solve that problem
the monitor startup good,all |
| Re: Blown Fuse - Troubleshoot Why | Solution Found! I replaced the fuse with a resettable fuse (Littelfuse 60R020). Now, when I startu |
| Full Screen | Hello, If you go into the BIOS/setup screen during the boot up sequence, you should see an option i |
| Samsung Syncmaster | Hiya
I wonder if anyone can help with a problem i am having with a Samsung Syncmaster 711mp monit |
| AT49F002T-50TC data | [b:0e0ec7fbac]Features[/b:0e0ec7fbac]
• Single-voltage Operation
– 5V Read
– 5V Reprogramming
• |
|
|
| minnie dosent this set have that 18 pin ic for high voltage startup and regulation.3001? on top of i |
| A light bulb has very low resistance when it is cold, and will draw a huge startup current (up to te |
| Flashing Red and Green LED | Dear sir,
Something had gone wrong lately with my Sony KCSV29M TV set. The set kept on flashing ( |
| Aha, I was not aware this is the unit that plays both sides;
At this point, I think you are better |
| does anyone know if penn foster good school to attend at such low cost.They say their nationally acc |
| Samsung LE37A656 | I have the above lcd and it keeps defaulting to dynamic mode.
I have tried a reset but to no avail. |
| RCA | The most obvious answer is a blown fuse. If it isn't a blown fuse, it is probably a defective semic |
| replace the ic close to the flyback.16 or 18 pins for high voltage startup.---3001. |
| Problem solved!
After nearly buying another XBoard on Ebay for just under £100 (but thankfully |
| The regulated 5V line is monitored using Q2314 and Zener diode D2310 (3.6V) on the M-board. The outp |
| How can i check the lens of a dvd | The problem with this dvd is that not read the disc. The sequence that happens in this way.
1.- whe |
| Re: Workaround on ACER AL1511 | [quote="donz"]Hi. I have the same problem with Acer AL1511 monitor on AcerPower F1 PC. It |
| Workaround on ACER AL1511 | Hi. I have the same problem with Acer AL1511 monitor on AcerPower F1 PC. It initially appears to sta |