Subject | Text |
hi | you could either use a variable resistor but a powerfull one like 10k/3W
you conect the 1st and 2nd |
| The resistance
Across
C32 1st test=18.05 M ohm and dropping
2nd test=30.15 M ohm and |
|
| hi mate,
please note with most models of these cameras as long as you have proff of purchase |
| 1st item) Because you don't seem to have any high voltage, I'll would start by checking the HOT (lar |
Re: vert or horiz problem? | [quote:7b7d7f4d23="jts1957"]1st - It's JTS1957 / NOT JTS1975. Oh, to be 18 again! How did we get fro |
Re: Renault Radio Code Help | [quote:1f01e623db="seke123"][quote:1f01e623db="Dekster"][quote:1f01e623db="seke123"]Hello.
We chang |
| Your CRT is getting a layer of dead material on the cathodes of each gun.3 options.Take to repair sh |
Free Manuals | It's our 3rd anniversary at http://www.justmanuals.com and to thank our loyal customers, we are offe |
tv u/s | could be any of comp mentioned- generally r/p cheapest 1st- really have to know what each does- not |
| no no, if you click on 1st TOSHIBA on that page & scroll down to 21N21.
I'm pretty sure the o |
Canon NP3030 Copier PSU problem | Hi,
As above, I have a canon NP3030 copier that has a flaky power supply, swapping the PSU with a k |
Re: DX-LCD32-09 | If you replaced both that means the LCD panel is bad.
[quote:90c7c4a8dd="ddizzleh"]I too have t |
| Hi madmatt2024, how are you doing?
I am back again. wow! you've give me a nice picture illustrat |
Philips combi tuning - help needed please | --------------------------------------------------------------------------------
Hi guys,
When I |
location | 1st fuse towards the rear is blown on the board with convergence chips. i.e. location is F1602. |
| [quote:d9faf1a38a="jts1957"]That's sort of like asking for Goodyear Assurance TripleTred tires for y |
| so it could be the control IC, can u give me some ideas about that IC's function & it's cause's |
|
| [quote:18a63d2739="jts1957"]I put a new diode in D31 and everything connected. [color=red:18a63d2739 |
need help w/ broken Sony PVM 20L5 monitor | Looks like a horiz flyback problem, there is low voltage present but no high voltage ( or picture ). |
| Just go to the menu, and select the following function:
1) 1st select "Fax Functions"
2) The go |
Re: Same TV, Same Problem.... | Hi..just to shere my knowledge..i from malaysia but i think the basic still same..i have lot experie |
Re: I have a code but can't insert it - blaupunkt | [quote:575379e589="milimitar2"]Hi,
any idea how can input the code in blaubunkt car radio of suzuk |
| Hi Err.. BITCH,
Thx for trying to help but I can only see the 1st page of the svc manual? :? |
| If an edge connector has a pin that's marked 12V and you're measuring 24V, I'd check that out 1st.
|
RAM AND HDD UPGRADE | Main Chipset Intel 830MG
System Bus/FSB 133 MHz
BIOS Size/Name Inside Plug and Play (1.0a) 1x 256K |
parts availability | You need to look at the"Song-Beverly Consumer Warranty Act...".
Civil Code Section 1793. |
| and the chassis number is ptk169pga in case this is needed, i forgot it in my 1st post |
Newby Help - Gaming wheel - TIP42C transistor fried | I've got a really nice Fanatec Speedster wheel for my 1st gen xbox. Today the force feedback from th |
enclosed pictures | The 1st time the replacement transistor was fitted the insulating washer must not of been fitted cor |
Error code | C 0910 =2nd Drawer Paper Lift-up Failure
C 0d50=Duplex Unit Drive motor M31`s Fail to Turn
C 0F20= |