Subject | Text |
| I have chema to contactar Fernando Trindade [email protected] I wait that this value helps R543=10K i |
| I've already checked those transistors. The solder joints seem okay.
I tested the tube's blue gun |
|
Philips 9P6444C103 | hi guys, I am new to this board and have a problem with my Philips 9P6444C103. It is a 64" r |
Sourcing pots for E-MU Xboard keyboard | Hi everybody, I am trying to fix my E-MU Xboard keyboard, the mod wheel pot is jumping from 0 to 127 |
R443 & 445 | Yes, an interesting design! Thanks for the info and your very good advice - agreed.
Can you help |
hi | you could either use a variable resistor but a powerfull one like 10k/3W
you conect the 1st and 2nd |
Bad caps in Philips TV | I have the same problem with the 27pt543s37a. There was a problem with counterfeit electrolyte in al |
| I realize this discussion is a few months old at this point, but I wanted to chime in with informati |
| In looking at your first set of pictures, apparently those are in fact rotary encoders which are com |
DTC143 question | I have one question: Can I use a transistor DTC143X (S) instead of transistor DTC143Z (SA)? It is in |
Simple idea/circuit to control REC / STOP for home VCR noX10 | I know X10 has the VCR Commander. As a last resort I might use it. I have two and they've worked fo |
The Open Drain Output Troubles about STC12C5A | Good afternoon,sir
Recently I am involved in a project that controlling an analog switch--CD4066. H |
| [quote:38748f7c21="vtech"]In looking at your first set of pictures, apparently those are in fact rot |
| I had the same problem and I solved in this way (cut & paste from nl.hobby.video newsgroup messa |
| Set shuts down intermittently and has to be unplug and replug for it to restart
replace C832 USE 3 |
component tester shematics? | Hi there!
i plan on building a small but usefull component tester to use with my oscilloscope.
i f |
Philips 190/B6 Monitor OSD Fault. | Hi all newbie to this board here. Been having some problems with my Philips 190/B6 and the OSD inter |
|
backlighting led monitor | Replacing r 1 resistor on 701-cpt with 10k .25 watt resistor as listed on schematic supplied by pdf |
| Chech r216 10k ohm to see if it's burnt. If so you need to replace the resistor and flyback. Most co |
| Check R15101(10K) |
| Keep in mind that in general, any guitar amplifier input must see some sort of a resistance between |
Toshibas and the like | Hi there Larry and Tibor,
last night I repaired my Toshiba. Larry, you are completely right, the |
Faulty Black Diamond Tv | Not sure but it may be AK19PRO chassis. I copied and pasted fault info on AK19 series below to see i |
Toshiba TV 14R21 (PWB-1386 Board) keeps power on and off | [quote:b8bfe93703="minnie"]Chech r216 10k ohm to see if it's burnt. If so you need to replace the re |
| Bingo
All you need is a 10K 1/2 watt standard resistor. :) |
| CHECK C701, THE POLARITY MARKED ON THE BOARD IS SOMETIMES INCORRECT, THE POSITIVE LEG OF THE CAP SHO |
| r15= 1k Ohm
r18=22 Ohm
r20=10k Ohm
Use google and search on AC8080LF
Some Polish sites have l |
Sony KD-28DL11U (FE2D) - 8V error - 11 blinks | Hi, I have a Sony KD-28DL11U that is reporting a code 11 "Jungle Controller 8V error". The |
| Hi jts, I haven't tried that, but I did disassemble the 10k pot (the lower set of two photos) so tha |