| Subject | Text |
| Alingment instructions needed phillips/magnavox combo | It is model CCXAT252 manufactured around 1999, not sure who made vcr possibly a Funai unit.
Thanks |
| FUJITSU 4209 Plasma Display service manual needed | Anyone have one of these or know where I could obtain one? Thank you in advance. |
|
|
| Help with my Panasonic 65" plasma | I seem to be having a problem with my Panasonic Plasma, Model: TH65PZ850U. If anyone has a schematic |
| Phillips MX5600D/37 home theater system | This unit has stand by power but won't turn on... Thanks for any help.. |
| phillips 483531057673 Installation sheet | Help i got the kit but no instructions. Can someone email it to me. Thanks.
Tj's tv & appliance |
| Intelligent power module (IPM) repair- Hitachi 42" Plas | Anybody ever try and repair one of these ? I've got a YPPD J007C that has a blown component.
Its |
| Phillips 21PT 1664 | Can anyone help please.
I am trying to connect a digital camera onto the above model to show phot |
| Re: PLASMA JVC GD-V4210 PCE no picture | [quote:45774371e7="anton"][quote:45774371e7="ajjc"]hi i have a JVC GD-V4210 PCE it has power but it |
| Phillips Magnavox rear projector big screen TV has red spot | Philips Magnavox rear projector big screen TV mod.# 8p6054c101 has red spot on screen in lower middl |
| thompson 42ins plasma tv | this set goes off after going for about 5 hours. any help will be appreciated |
| Phillips 28PW6332/05 Software Protection | I've spent a while narrowing down the problem with this TV. One day it shut off and started continuo |
| Manual Oscillo Phillips PM3217 | Hi, you'll be able to find get it by this link : http://shatterscape.com/misc/Philips_PM3217_oscillo |
| PLASMA | I AM WORKING ON 1 OF THESE PLASMAS WITH SAME FAULT, SPARES ARE NOT AVAIL SEPARETLY, HAVING TO REPLAC |
| Re: phillips matchline 29" TV | [quote="jak"]Hi I justed started to get a squeezing of the picture to the right of the screen. The |
| Plasma TV Hantarex PDP42QV | We need schematic of power pcb.Thanks! |
| 42" plasma | Did you find out from the shop what the problem was. If so how much did it cost to get it fixed??? T |
| NEC 61mp1 (plasma) w/various stuck vert lines on bot 1/2 scr | I recently acquired an NEC 61MP1/61MX1A that has several vertical columns of stuck pixels (some R, s |
|
|
| Sears LXI Projection TV with no picture | This is a 60" CRT rear projection TV that powers on but with no picture. There are no menus or |
| philips 21PT4457/05 | this philips when switched on presents a flaring picture and poor picture quality after checking the |
| pleas code | MADE IN SOUTH AFRICA
BECKER AUTOMOTIVE
EC: 105
24 VOLT
Q02
ZGS003
TYPE: TRUCKLINE CC30
MODEL |
| Toshiba 865B VCR digital auto & manual tracking ineffect | Trying to remember the deck used in this machine as been out of the trade a few years now (memory go |
| Thanks for the tip guys. | Replaced it with a 105 degrees version. And voila it worked like a charm again. I also left the lead |
| ASC20130528001 | I was wondering where you obtained a copy of the firmware noted in this service bulletin (ASC2013052 |
| If you get a diagram you can see what you are soldering:)
If not, replace the electrolytics around |
| awg stands for | in briefly AWG is American Wire Gauge and means diameter size is 18 and both cables should has the s |
| Sony KE-42TS2U | No LED. Plug in plasma and it turns on for 10 sec. then shuts off. |
| If an edge connector has a pin that's marked 12V and you're measuring 24V, I'd check that out 1st.
|
| [quote:966af3158a="ben444"]Hi, looking for code for following:
BP 2020
92 105 541
BP0485 2 7952 |
| Fujitsu plasmavision pds4229 - big power supply problem | Hello to all,
i have this plasma display after higher voltage in power line..
have someone sch |
| Please help | I too have been trying to fix my radio for months have just got it out today in my Barina. Blaupunkt |
