| Subject | Text |
| wavetek 144 sweep generator mainboard test points | wondering if anyone might have the main board assembly pic from the service manual that shows the te |
| service manual for wavetek 144 sweep generator need drawing | i need drawing number 0103-00-0052 (main board assembly parts layout) - old drawing number is 144-0 |
|
|
| WAVETEK 1002 Sweep Generator | Hi All,
I need a schematic/service manual for this unit.
tnx |
| Zenith | About 2/3rds of the sets that come into my shop are Zeniths that were manufactured in the early to l |
| Anritsu S331D PLL fail | Hi, I have an Anritsu sitemaster S331D which fails self test with the error
PLL FAILED (2000,10) |
| First off, it's not a fuse or thermistor. If it was that failure, your set would be dead! Second w |
| I don't know how to search for a Service Manual | Hi all:
I am searching for a Service and User Manual for,
Wavetek Model 164 30 MHz Sweep Functio |
| Any other suspects other than the jungle IC? | My 15-inch Mag CRT monitor (model D510) first started its symptoms with an intermittent loss of vert |
| hello torbjorn,
yes i am using a cheap (sears craftsman)digital multimeter with a 200/600vac settin |
| hey guys, i'd like to fix my Z50Z83D8 i'm getting kinda tired of my 19' backup tv :( is 9-1674-03 |
| BK Precision 3017A | I need a service manual for a BK precision 3017A sweep function Generator. Thanks |
| If you take the back of the set off the inside of the back will tell you the parts numbers of the mo |
| Power supply/sweep module 9-1674-03.
http://www.tvparts.com/
$95/$105 cost. List, double it. To g |
| There are modules in this set. Take the front speaker grill off, turn the screen control up and see |
| turn set on. when screen comes on hold vol down button on the tv until vol bar is at zero. continue |
| Maybe this will help too | Printable Version of Topic
Click here to view this topic in its original format
Repairworld _ Tele |
| Sounds strange to me that initially you could get a sweep across the screen either horizontally or v |
|
|
| Problem solved!
After nearly buying another XBoard on Ebay for just under £100 (but thankfully |
| bk 2160 scope problem | Aler,
Forget all the other advice you have received so far. If pressing the beam finder button doe |
| Pop the back off and what modules do you have in there for the sweep/deflection board and signal boa |
| TCE CTC 187
NO HORIZONTAL SWEEP (CTC 187CL)
C4404 has probably blown up
Caused by an open C4403 |
| Sound Card Oscilloscope, Spectrum Analyzer, Signal Generator | PC version: http://www.virtins.com/SCMISetup.exe
Pocket PC version: http://www.virtins.com/PocketI |
| You've lost your vertical sweep. Check the vertical output circuits, especially the vertical output |
| :idea: Found the following:
1) C951 = 4.7ufd/250V
2) Suggest changing these caps in standby po |
| S33x Integrator fault | The fault is probably NOT in the RF-input; Rather is it the VCO-step integrator, that have lost a bi |
| Pin cushion problem | Hi...
Don't know this model , sorry . I would look for a bad FET or Bipolar transistor that modulat |
| WAVETEK 144 SWEEPER MANUAL AND HELP FOR REPAIR | Hello , I am searching the full repair manual for the WAVETEK 144 sweeper
please help and send to |
| SCMI---Great Test & Measurement Software for free downlo | website: http://www.virtins.com
PC version: http://www.virtins.com/SCMISetup.exe
Pocket PC Versio |
| If you really like the unit, then take it to a shop and have it fixed. My opinion and service histo |
| Re: Mitsubishi | When set had "Vert Hold" problem (Picture/Screen ROLLING?), could you make out any video? |