Text preview for : Panel_AUO_B170UW01_V2_0_[DS].pdf part of . Various Panel AUO B170UW01 V2 0 [DS] . Various LCD Panels Panel_AUO_B170UW01_V2_0_[DS].pdf
Back to : Panel_AUO_B170UW01_V2_0_[ | Home
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
( ) Preliminary Specifications
( V ) Final Specifications
Module 17.0" WUXGA Color TFT-LCD
l
Model Name B170UW01 V2 (HW 1A)
tia
en
Customer Date Ap
Approved by Date
fid
Beyond Yang 09/03/2008
on
Checked &
Date Prepared by Date
C
Approved by
y
Claire Yu 09/03/2008
Note: This Specification is subject to change NBBU Marketing Division /
without notice. AU Optronics corporation
AUO NBBU spec. Template 1.0 1 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions............................................................... 4
2. General Description ................................................................. 5
2.1 General Specification ......................................................................................................................5
2.2 Optical Characteristics ....................................................................................................................6
3. Functional Block Diagram ...................................................... 11
4. Absolute Maximum Ratings.................................................... 12
4.1 Absolute Ratings of TFT LCD Module..........................................................................................12
..
4.2 Absolute Ratings of Backlight Unit ...............................................................................................12
..............
...
4.3 Absolute Ratings of Environment ..................................................................................................12
5. Electrical characteristics ........................................................ 13
...............
. . .
l
tia
5.1 TFT LCD Module.........................................................................................................................13
..... .... ............
. . ... .
..... .......... ....
.... ...
5.2 Backlight Unit...............................................................................................................................15
6. Signal Characteristic .............................................................. 17
........... ....
.. ...
en
6.1 Pixel Format Image.......................................................................................................................17
..................
. ..........
................. .......
.. . ......
6.2 The input data format....................................................................................................................18
.............. ........
. ...............
6.3 Signal Description/Pin Assignment ................................................................................................19
....... ...............
. ...
6.4 Interface Timing............................................................................................................................21
fid
7. Connector Description ........................................................... 24
n ........ ....
. . ..
7.1 TFT LCD Module.........................................................................................................................24
...... ....
....... .........
........
. .............
...
7.2 Backlight Unit...............................................................................................................................24
on
cto r ............
.... ...
7.3 Signal for Lamp connector ............................................................................................................24
8. Dynamic Test .. ........
est ...
......................................................................... 25
.
8.1 Vibration Test ...............................................................................................................................25
est .................. .
t ...
C
ec: .........
...
8.2 Shock Test Spec: ..........................................................................................................................25
9. Reliability .............................................................................. 26
..
10. Mechanical Characteristics................................................... 27
10.1 LCM Outline Dimension .............................................................................................................27
10.2 Screw Hole Depth and Center Position .......................................................................................29
11. Shipping and Package.......................................................... 30
11.1 Shipping Label Format ................................................................................................................30
11.2 Carton package ...........................................................................................................................31
11.3 Shipping package of palletizing sequence ....................................................................................31
12. Appendix: EDID description ................................................. 32
AUO NBBU spec. Template 1.0 2 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page Old description New Description Remark
0.1 2008/6/17 All First Edition for Customer
0.2 2008/9/3 32 Update EDID
l
tia
en
fid
on
C
AUO NBBU spec. Template 1.0 3 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static e ic electricity and insure
c
human earth when handling.
l
7) Do not open nor modify the Module Assembly.
tia
8) Do not press the reflector sheet at the back of the module to any directions.
dule to any dire
u y
9) In case if a Module has to be put back into the packing con ine slot after once it was
acking container
g onta
taken out from the container, do not press the center of the CCFL Reflector edge.
he c en r of the
enter
en
Instead, press at the far ends of the CCFL Reflector edg softly. Otherwise the TFT
L Reflector edge
Module may be damaged.
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
gnal Interface C
erf
r
fid
tilt the Interface Connector of the TFT Module.
TFT Module.
F Mo .
11)After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
Module int
odu to
example), do not twist nor bend the TFT Module even momentary. At designing the
end the TFT
nd
on
enclosure, it should be taken into consideration that no bending/twisting forces are
aken into c o
n
T Module from
od e ro
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
fluorescent lam
uo t m
12)Cold cathode fluorescent lamp (CCFL) in LCD contains a small amount of mercury. Please
C
nces
follow local ordinances or regulations for disposal.
te
13)Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
14)The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
AUO NBBU spec. Template 1.0 4 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
2. General Description
B170UW01 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and backlight system. The screen format is intended to support the WUXGA
(1920(H) x 1200(V)) screen and 262k colors (RGB 6-bits data driver) without backlight inverter.
All input signals are LVDS interface compatible.
B170UW01 V0 is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 condition:
on
Items Unit Specifications
Specificatio
peci
l
tia
Screen Diagonal [mm] 433 (17"W)
)
Active Area [mm] 367.2 X 229.5
229.5
29
Pixels H x V 1920x3(RGB) x 12
920x3(RGB) 1200
3(R B
en
Pixel Pitch [mm] 0.1912X0.1912
0.19 2X0.19
1912 191
Pixel Format R.G.B. V
R.G.B. Vertical Stripe
B
fid
Display Mode Nor
Normally White
White Luminance (ICCFL=6.0mA)
) [c d/m2]
/m
[cd/m 260 typ. (5 points average)
Note: ICCFL is lamp current 220 min. (5 points average)
on
(Note1)
Luminance Uniformity
y 1.25 max. (5 points)
Contrast Ratio 500 min
Response Time [ms] 8 typ / 15 Max
C
Nominal Input Voltage VDD
ge VDD [Volt] +3.4 typ.
Power Consumption [Watt] 8.7W max.
Weight [Grams] 680 max.
Physical Size [mm] L W T
Max 382.7 245.1 6.6
Typical 382.2 - -
Min 381.7 - -
Electrical Interface 2 channel LVDS
Surface Treatment Glare, Hardness 4H,
AUO NBBU spec. Template 1.0 5 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Support Color 262K colors ( RGB 6-bit )
Temperature Range
o
Operating [ C] 0 to +50
Storage (Non-Operating) [oC] -20 to +60
RoHS Compliance RoHS Compliance
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 (Room Temperature) :
Tem
Item Unit Conditions n.
Min. Typ.
Typ. Max. Note
l
2
White Luminance [cd/m ] 5 points average
22
20
220 260
260 - 1, 4, 5.
tia
ICCFL=6.0mA
[degree] Horizontal (Right)
Right)) - 70 -
[degree] CR = 10 (Left)
ft) - 70 -
Viewing Angle 8
en
[degree] Vertical (Upper)
(Upper)
ppe - 60 -
[degree] CR = 10 (Lower)
10 (Lower)
wer - 60 -
Luminance
Points
5 Points - - 1.25 1
Uniformity
fid
CR: Contrast Ratio 500 600 - 6
Cross talk % 4 7
ec]
c]
[msec] Rising - - -
on
Response Time [msec]
msec] Falling - - - 8
m
[msec]
[msec] Rising + Falling - 8 15
Red x 0.590 0.620 0.650
C
Red y 0.323 0.353 0.383
Green x 0.280 0.310 0.340
Chromaticity of color Green y 0.540 0.570 0.600
Coordinates 2,8
(CIE 1931) Blue x 0.126 0.156 0.186
Blue y 0.114 0.144 0.174
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359
NTSC % CIE 1931 45 50 -
AUO NBBU spec. Template 1.0 6 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Note 1: 5 points position (Ref: Active area)
W
W /4 W /4 W /4 W /4
H /4
1 2
H /4
H 3
H /4
4 5
l
H /4
Note 2: 13 points position (Ref: Active area)
tia
en
W
W /4 W /4
4 W /4 W /4
10 10
fid
10
1 2 3
H /4
4 5
on
H /4
H 6 7 8
H /4
C
9 10
H /4 11 12 13
10
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
Maximum Brightness of five points
W5 =
Minimum Brightness of five points
Maximum Brightness of thirteen points
W13 =
Minimum Brightness of thirteen points
Note 4: Measurement method
AUO NBBU spec. Template 1.0 7 of 35
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.
Photo detector
Field=2
l
tia
en 50 cm
m
LCD Panel TFT-LCD
fid
Cent r
Center of the sc
e screen
Note 5 Definition of Average Luminance of White (YL):
ance of W hite (
n Wh
on
Measure the luminance of g ay level 63 at 5 points YL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
gray level 63 t
y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
ng to
g luminance
m anc
C
Note 6 Definition of contrast ratio:
ast r
t
Contrast ratio is calculated with the following formula.
Brightness on the "White" state
Contrast ratio (CR)=
Brightness on the "Black" state
Note 7 Definition of Cross Talk (CT)
CT = | YB