Text preview for : Panel_AUO_M190PW01_V0_0_[DS].pdf part of . Various Panel AUO M190PW01 V0 0 [DS] . Various LCD Panels Panel_AUO_M190PW01_V0_0_[DS].pdf
Back to : Panel_AUO_M190PW01_V0_0_[ | Home
M190PW01 V0
Document Version: 0.1
Date: 2006/04/17
Product Functional Specification
19 inch WSXGA+ Color TFT LCD Module
Model Name: M190PW01 V0
(u ) Preliminary Specification
( ) Final Specification
Note: This Specification is subject to change without notice.
(C) Copyright AU Optronics Ver 0.1 1/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
AU OPTRONICS CORPORATION
Product Specification
19"Wide SXGA+ Color TFT-LCD Module
Model Name: M190PW01 V.0
Approved by Prepared by
DDBU Marketing Division / AU Optronics corporation
Customer Checked & Approved by
(C) Copyright AU Optronics Ver 0.1 2/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
Contents
1.0 Handling Precautions............................................................. 5
2.0 General Description ............................................................... 6
2.1 Display Characteristics .............................................................................................................. 6
2.2 Optical Characteristics ............................................................................................................... 6
3.0 Functional Block Diagram .................................................... 10
4.0 Absolute Maximum Ratings.................................................. 11
4.1 TFT LCD Module ...................................................................................................................... 11
4.2 Backlight Unit ............................................................................................................................ 11
4.3 Absolute Ratings of Environment ............................................................................................ 11
5.0 Electrical characteristics...................................................... 11
5.1 TFT LCD Module ...................................................................................................................... 11
5.1.1 Power Specification............................................................................................... 12
5.1.2 Signal Electrical Characteristics.............................................................................. 12
5.2 Backlight Unit ............................................................................................................................ 13
6.0 Signal Characteristic............................................................ 14
6.1 Pixel Format Image................................................................................................................... 14
6.2 The input data format ............................................................................................................... 15
6.3 Signal Description .................................................................................................................... 16
6.4 Timing Characteristics.............................................................................................................. 17
6.4.1 Timing diagram .................................................................................................... 18
6.5 Power ON/OFF Sequence ....................................................................................................... 19
7.0 Connector & Pin Assignment................................................ 20
7.1 TFT LCD Module ...................................................................................................................... 20
7.2 Backlight Unit ............................................................................................................................ 20
7.3 Signal for Lamp connector ....................................................................................................... 21
8.0 Reliability ............................................................................ 21
9.0 Environment ........................................................................ 22
9.1 Temperature and Humidity ....................................................................................................... 22
9.1.1 Operating Conditions ............................................................................................ 22
9.1.2 Shipping Conditions .............................................................................................. 22
9.2 Atmospheric Pressure .............................................................................................................. 22
9.3 Thermal Shock .......................................................................................................................... 22
10.0 Reliability .......................................................................... 23
10.1 Failure Criteria ........................................................................................................................ 23
10.2 Failure Rate ............................................................................................................................ 23
10.2.1 Usage................................................................................................................ 23
10.2.1 Component De-rating.......................................................................................... 23
(C) Copyright AU Optronics Ver 0.1 3/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
10.3 On/OFF Cycle ......................................................................................................................... 23
11.0 Safety ................................................................................ 23
11.1 Sharp Edge Requirements..................................................................................................... 23
11.2 Materials .................................................................................................................................. 23
11.2.1 Toxicity ............................................................................................................. 23
11.2.2 Flammability ...................................................................................................... 24
11.3 Capacitors................................................................................................................................ 24
12.0 Other requirement ............................................................. 24
12.1 National Test Lab Requirement ............................................................................................. 24
12.2 Label ........................................................................................................................................ 24
13.0 Mechanical Characteristics................................................... 2
Record of Revision
Version and
Page Old description New Description Remark
Date
0.1 2006/04/17 All First Edition for Customer All
(C) Copyright AU Optronics Ver 0.1 4/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press or pat the panel surface by fingers,hand or tooling
9) Do not press the reflector sheet at the back of the module to any directions.
10) In case if a module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL
reflector edge softly. Otherwise the TFT module may be damaged.
11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT module.
12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor
bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that
no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be
damaged.
(C) Copyright AU Optronics Ver 0.1 5/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
2.0 General Description
This specification applies to the 19 inch-wide Color TFT-LCD Module M190PW01.
The display supports the WSXGA+ (1440(H) x 900(V)) screen format and 16.7M colors. All input signals are 2 Channel
LVDS interface compatible.
This module does not contain an inverter card for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 condition:
ITEMS Unit SPECIFICATIONS
Active Area [mm] 408.24 (H) x 255.15(V)
Pixels H x V 1440(x3) x 900
Pixel Pitch [mm] 0.2835x 0.2835
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode,Normally White
White Luminance ( Center ) [cd/m2] 300 cd/m2 @6.5mA (Typ)
Contrast Ratio 800 : 1 (Typ)
Optical Response Time [msec] 5ms (Typ, on/off)
Color Saturation 72% NTSC
Nominal Input Voltage VDD [Volt] +5.0 V
Power Consumption [Watt] 19.5W (Typ)
(VDD line + CCFL line)
Weight [Grams] 2500 (Typ)
Physical Size [mm] 428.0(W) x 278.0(H) x 19.0(D) (Typ)
Electrical Interface LVDS
Support Color 16.7M colors
Temperature Range
Operating [oC] 0 to +50
Storage (Shipping) [oC] -20 to +60
Surface Treatment Hard-coating (3H)
RoHS RoHS compliance
(C) Copyright AU Optronics Ver 0.1 6/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25:
Item Unit Conditions Min. Typ. Max. Note
Viewing Angle [degree] Horizontal -
(Right)+ (Left) 150 160 -
CR = 10
[degree] Vertical -
(Up) + (Down) 150 160 -
CR = 10
Contrast ratio Normal Direction 600 800
Response Time [msec] Raising Time 3.6
- 5.7 Note 1
[msec] Falling Time
- 1.4 2.3 Note 1
[msec] Rising + Falling
- 5 8 Note 1
Color / Chromaticity Red x
0.61 0.64 0.67
Coordinates (CIE)
Red y
0.32 0.35 0.38
Green x
0.26 0.29 0.32
Green y
0.59 0.62 0.65
Blue x
0.11 0.14 0.17
Blue y
0.04 0.07 0.1
White x
Color Coordinates (CIE) White 0.28 0.31 0.34
White y
0.3 0.33 0.36
White Luminance at CCFL 6.5mA 2
(central point) [cd/m ]
250 300 -
Luminance Uniformity
[%] 75 80 - Note 2
Crosstalk (in75Hz)
[%] 1.5 Note 3
Flicker DB -20 Note 4
Equipment: Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A ,
BM 7 ,CS-1000, & EZContrast* )
Aperture : 1with 100cm viewing distance (VD) or 2with 50cm viewing distance (VD)
Test Point: Center (VESA point 9)
Environment: < 1 lux
LCD Module
PR-880 /
BM5A /
BM7
/CS-1000
measuring distance 0
Module Driving Equipment
*' EZ Contrast is different measurement tool with very close viewing distance.
(C) Copyright AU Optronics Ver 0.1 7/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
Note 1: Definition of Response time
The output signals of photo detector are measured when the input signals are changed from "Black" to "White" (rising
time), and from "White" to "Black "(falling time), respectively. The response time is interval between the 10% and
90% of amplitudes.
Note 2: Brightness uniformity of these 9 points is defined as below
90 % 50 % 10 %
10 %
50 %
90 %
Minimum Luminance in 9 points (1 - 9)
Uniformity = x 100%
Maximum Luminance in 9 Points (1 - 9)
(C) Copyright AU Optronics Ver 0.1 8/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
Note 3: Crosstalk is defined as below :
1/2 1/6 2/3 1/2 1/3 1/6
1/6
A A' 1/6
1/3
1/2 1/2
B B'
2/3
184 gray level 184 gray level
Unit: percentage of dimension of display area 0 gray level
l LA-LA' l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B
l LB-LB' l / LB x 100%= 1.5% max., LA' and LB' are brightness at location A' and B'
Note 4: Test Paterm: Subchecker Pattern
RGB R GB
Gray Level = L127
RGB R GB
Gray Level = L0
RGB R GB
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
AC
DC
Time
AC Level(at 30 Hz)
Flicker (dB) = 20 log
DC Level
(C) Copyright AU Optronics Ver 0.1 9/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
3.0 Functional Block Diagram
The following diagram shows the functional block of the 19 inches wide Color TFT/LCD Module:
AUO ASIC
G1
Y-Driver IC
LVDS Timing TFT-LCD
LVDS Receiver Controller 1440*(3)*900
Connector
Pixels
+ 5V
G900 X-Driver IC
D1 D4320
4 CCFL
Gamma
DC/DC
Correction
Converter
DC POWER
I/F + X-PCB
Inverter
JAE FI-XB30SSL-HF15 JST BHSR-02VS-1
Mating Type: FI-X30HL Mating Type: SM02B-BHSS-1-TB
(C) Copyright AU Optronics Ver 0.1 10/27
2004 All Rights Reserved.
No Reproduction and Redistribution Allowed.
M190PW01 V0
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive VIN -0.3 +5.5 [Volt] Note 1,2
4.2 Backlight Unit
Item Symbol Min Max Unit Conditions
CCFL Current ICFL - 8 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Humidity HOP 5 95 [%RH] Note
o
Storage Temperature TST -20 +60 [ C] Note
Storage Humidity HST 8 95 [%RH] Note
Note 1: With in Ta (25 )
Note 2: Permanent damage to the device may occur if exceed maximum values
Relative Humidity %
Twb=39
T=40,H=95%
100
95
80
T=50,H=55%
60
T=60,H=39%
Storage
40 range Operation range T=65,H=29%
20 Storage
range
5
(C) Copyright AU Optronics
0 Ver 0.1 11/27
-20
2004 All Rights Reserved. 0 50 60
Temperature C
No Reproduction and Redistribution Allowed.
M190PW01 V0
5.0 Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
Symbol Parameter Min Typ Max Units Condition
Logic/LCD Drive
VDD 4.5 5 5.5 [Volt]