Text preview for : Panel_Panasonic_VVX19H101G00_0_[DS].pdf part of . Various Panel Panasonic VVX19H101G00 0 [DS] . Various LCD Panels Panel_Panasonic_VVX19H101G00_0_[DS].pdf
Back to : Panel_Panasonic_VVX19H101 | Home
Panasonic Liquid Crystal Display Co.,Ltd.
For Messrs. Panasonic Corporation Group
TECHNICAL DATA
VVX19H101G00
CONTENTS
No. Item Sheet No Page
- COVER ATD-5705 2601 VVX19H101G00 1-1/22/2
- RECORD OF REVISION ATD-5705 2602 VVX19H101G00 2-1/1
- DESCRIPTION ATD-5705 2603 VVX19H101G00 3-1/1
1 ABSOLUTE MAXIMUM RATINGS ATD-5705 2604 VVX19H101G00 4-1/22/2
2 INITIAL OPTICAL CHARACTERISTICS ATD-5705 2605 VVX19H101G00 5-1/22/2
3 ELECTRICAL CHARACTERISTICS ATD-5705 2606 VVX19H101G00 6-1/22/2
4 BLOCK DIAGRAM ATD-5705 2607 VVX19H101G00 7-1/1
5 INTERFACE PIN ASSIGNMENT ATD-5705 2608 VVX19H101G00 8-1/44/4
6 INTERFACE TIMING ATD-5705 2609 VVX19H101G00 9-1/55/5
7 DIMENSIONAL OUTLINE ATD-5705 2610 VVX19H101G00 10-1/22/2
8 LABEL FORMAT ATD-5705 2611 VVX19H101G00 11/1/1
9 COSMETIC SPECIFICATIONS ATD-5705 2612 VVX19H101G00 12/1/33/3
10 PRECAUTION ATD-5705 2613 VVX19H101G00 13/1/33/3
11
12
13
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2601 VVX19H101G00 Page 1-2/2
RECORD OF REVISION
The upper section : Previous revision
The lower section : New revision
Date Summary
Sheet No. Page
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2602 VVX19H101G00 Page 2-1/1
DESCRIPTION
The following specifications are applied to the following IPS-Pro-TFT LCD module.
Note : The timing controller function is not built in this module.
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2603 VVX19H101G00 Page 3-1/1
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2604 VVX19H101G00 Page 4-1/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2604 VVX19H101G00 Page 4-2/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2605 VVX19H101G00 Page 5-1/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2605 VVX19H101G00 Page 5-2/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2606 VVX19H101G00 Page 6-1/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2606 VVX19H101G00 Page 6-2/2
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2607 VVX19H101G00 Page 7-1/1
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2608 VVX19H101G00 Page 8-1/4
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2608 VVX19H101G00 Page 8-2/4
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2608 VVX19H101G00 Page 8-3/4
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2608 VVX19H101G00 Page 8-4/4
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2609 VVX19H101G00 Page 9-1/5
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2609 VVX19H101G00 Page 9-2/5
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2609 VVX19H101G00 Page 9-3/5
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2609 VVX19H101G00 Page 9-4/5
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2609 VVX19H101G00 Page 9-5/5
7.DIMENSIONAL OUTLINE
(1) FRONT VIEW
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2610 VVX19H101G00 Page 10-1/2
(2) BACK VIEW
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2610 VVX19H101G00 Page 10-2/2
8. LABEL FORMAT
8.1 Label
The barcode nameplate is pasted on each module as illustration, and its definitions are as
following explanation.
REV. is the column for manufacturring convenience. A-Z except I and O may be
written on this column.
12 2012 CELL-
P REVISION
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2611 VVX19H101G00 Page 11-1/1
9. INSPECTION SPECIFICATION
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2612 VVX19H101G00 Page 12-1/3
3. INSPECTION CRITERIA
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2612 VVX19H101G00 Page 12-2/3
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2612 VVX19H101G00 Page 12-3/3
10. PRECAUTION
Please pay attention to the followings when a TFT module with a backlight unit is used, handled and mounted.
10.1 Precaution to handling and mounting
(1) Applying strong force to a part of the module may cause partial deformation of frame or mold, and cause damage
to the display.
(2) The module should gently and firmly be held by both hands. Never hold by just one hand in order to avoid any
internal damage. Never drop or hit the module.
(3) The module should be installed with mounting holes of a module.
(4) Uneven force such as twisted stress should not be applied to a module when a module is mounted on the cover
case. The cover case must have sufficient strength so that external force can not be transmitted directly to a module.
(5) It is recommended to leave a space between a module and a holding board of a module so that partial force is not
applied to a module.
B- Effective display
Cover Edge Polarize
cover
TFT
Fig.1 Cross sectional view of a above
(6) The edge of a cover case should be located inside more than 1mm from the edge of a module front frame.
(7) A transparent protective plate should be added on the display area of a module in order to protect a polarizer and
TFT cell.The transparent protective plate should have sufficient strength so that the plate can not touch a module
by external force.
(8) Materials included acetic acid and choline should not be used for a cover case as well as other parts and boards
near a module. Acetic acid attacks a polarizer. Choline attacks electric circuits due to electro-chemical reaction.
(9) The polarizer on a TFT cell should carefully be handled due to its softness, and should not be touched, pushed or
rubbed with glass, tweezers or anything harder than HB pencil lead. The surface of a polarizer should not be
touched and rubbed with bare hand, greasy clothes or dusty clothes.
(10) The surface of a polarizer should be gently wiped with absorbent cotton, chamois or other soft materials slightly
contained petroleum benzene when the surface becomes dirty. Normal-hexane or Isopropyl alcohol as cleaning
chemicals is recommended in order to clean adhesives which fix front/rear polarizers on a TFT cell. Other cleaning
chemicals such as acetone, toluen and alcohol should not be used to clean adhesives because they cause chemical
damage to a polarizer.
(11) Saliva or water drops should be immediately wiped off. Otherwise, the portion of a polarizer may be deformed
and its color may be faded.
(12) The module should not be opened or modified. It may cause not to operate properly.
(13) Metallic bezel of a module should not be handled with bare hand or dirty gloves. Otherwise, color of a metallic
frame may become dirty during its storage. It is recommended to use clean soft gloves and clean finger stalls
when a module is handled at incoming inspection process and production (assembly) process.
(14) Lamp(CCFL) cables should not be pulled and held.
10.2 Precaution to operation
(1) The ambient temperature near the operated module should be satisfied with the absolute maximum ratings. Unless
it meets the specifications, sufficient cooling system should be adopted to system.
(2) The spike noise causes the mis-operation of a module. The level of spike noise should be as follows:
-200mV over- and under- shoot of VDD +200mV
VDD including over- and under- shoot should be satisfied with the absolute maximum ratings.
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2613 VVX19H101G00 Page 13-1/3
(3) Optical response time, luminance and chromaticity depend on the temperature of a TFT module. Response time
and saturation time of LED luminance become longer at lower temperature operation.
(4) Sudden temperature change may cause dew on and/or in the a module. Dew makes damage to a polarizer and/or
electrical contacting portion. Dew causes fading of displayed quality.
(5) Fixed patterns displayed on a module for a long time may cause after-image. It will be recovered soon.
(6) A module has high frequency circuits. Sufficient suppression to electromagnetic interference should be done by
system manufacturers. Grounding and shielding methods may be effective to minimize the interference.
(7) Noise may be heard when a backlight is operated. If necessary, sufficient suppression should be done by system
manufacturers.
(8) The module should not be connected or removed while a main system works.
(9) Inserting or pulling I/F connectors causes any trouble when power supply and signal data are on-state.
I/F connectors should be inserted and pulled after power supply and signal data are turned off.
10.3 Electrostatic discharge control
(1) Since a module consists of a TFT cell and electronic circuits with CMOS-ICs, which are very weak to electrostatic
discharge, persons who are handling a module should be grounded through adequate methods such as a list band.
I/F connector pins should not be touched directly with bare hands.
(2) Protection film for a polarizer on a module should be slowly peeled off so that the electrostatic charge can be
minimized.
10.4 Precaution to strong light exposure
(1) A module should not be exposed under strong light. Otherwise, characteristics of a polarizer and color filter in
a module may be degraded.
10.5 Precaution to storage
When modules for replacement are stored for a long time, following precautions should be taken care of:
(1) Modules should be stored in a dark place. It is prohibited to apply sunlight or fluorescent light during storage.
Modules should be stored at 0 to 35 at normal humidity (60%RH or less).
(2) The surface of polarizers should not come in contact with any other object. It is recommended that modules
should be stored in the shipping box of Panasonic Liquid Crystal Display Co.,Ltd.
10.6 Precaution to handling protection film
(1) The protection film for polarizers should be pealed off slowly and carefully by persons who are electrically
grounded with adequate methods such as a list band. Besides, ionized air should be blown over during peeling
action. Dusts on a polarizer should be blown off by an ionized nitrogen gun and so on.
(2) The protection film should be peeling off without rubbing it to the polarizer. Because, if the film is rubbed
together with the polarizer, since the film is attached to the polarizer with a small amount of adhesive, the
adhesive may remain on a polarizer.
(3) The module with protection film should be stored on the conditions explained in 10.5 (1). However, in case
that the storage time is too long, adhesive may remain on a polarizer even after a protection film is peeled off.
Besides, in case that a module is stored at higher temperature and/or higher humidity, adhesive may remain on
a polarizer. The remained adhesive may cause non-uniformity of display image.
(4) The adhesive can be removed easily with Normal-Hexane or Isopropyl alcohol. The remained adhesive or its
vestige on the polarizer should be wiped off with absorbent cotton or other soft materials such as chamois
slightly contained Normal-Hexane or Isopropyl alcohol.
10.7 Safety
(1) Since a TFT cell and lamps are made of glass, handling to the broken module should be taken care sufficiently
in order not to be injured. Hands touched liquid crystal from a broken cell should be washed sufficiently.
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2613 VVX19H101G00 Page 13-2/3
(2) The module should not be taken apart during operation so that backlight drives by high voltage.
10.8 Environmental protection
Flexible printed circuits and printed circuits board used in a module contain small amount of lead. Please follow
local ordinance or regulations for its disposal.
10.9 Use restrictions and limitations
(1) This product is not authorized for use in life support devices or systems, military applications or other applications
which pose a significant risk of personal injury.
(2) In no event shall Panasonic Liquid Crystal Display Co.,Ltd. be liable for any incidental, indirect or consequential
damages in connection with the installation or use of this product, even if informed of the possibility thereof in
advance. These limitations apply to all causes of action in the aggregate, including without limitation breach
of contact, breach of warranty, negligence, strict liability, misrepresentation and other torts.
10.10 Precaution to setting inverter
(1) Please use inverter output waveform that satisfies following formulae.
0.9*2*Irms|Ip|1.1*2*Irms
0.9*2*Irms|I-p|1.1*2*Irms
Ip Peak value of lamp current at positive side
I-p Peak value of lamp current at negative side
Also, please use sine wave with symmetric positive and negative wave that both area and peak of IL and VL
waveforms are within 10% of asymmetry rate, and that do not develop spike wave. Otherwise there is a possibility
to develop lighting defect.
(2) After this product is stored for a long time, it might take longer to discharge lamp. It is recommended that
auxiliary illuminant (LED, etc.) is set.
(3) Since multiple lamps are closely-mounted to the backlight, please use inverter that output waveform is
synchronized. If different phase inverter is used, it might cause luminance depression or short life span
by phase difference.
10.11 Others
Electrical components which may not affect electrical performance are subjective to change without notice because
of their availability.
Panasonic Liquid Crystal Display Co.,Ltd. Date Apr.25,2012 Sheet No. ATD-5705 2613 VVX19H101G00 Page 13-3/3