| Make | Model | Problem | Solution | Date |
| | | |
| Found: 36
|
| Bush | 3114A | St/by only | R502 330k o/c | 14-09-04 |
| Goldstar | CB14A80E | Reduced width. 6-8 volts on supply pin of TDA8362 | Replace TDA8362. Supplying +12V to supply pin of TDA8362, restored width but with no hor. Synchronization. | 14-09-04 |
| Goldstar | CB14A80E | Reduced width. 6-8 volts on supply pin of TDA8362 | Replace TDA8362. Supplying +12V to supply pin of TDA8362, restored width but with no hor. Synchronization. | 14-09-04 |
| Goldstar | CB14A80E | Relay goes on, then off, immediately after switch on | Change memory chip St24C02C. | 14-09-04 |
| Goldstar | CI14A20 | No tuning - osd works | No 33v tuning supply - FR403 5R6 o/c | 14-09-04 |
| Goldstar | CI14A80 | Dead & ticking | FR802 in 25v line o/c; FET Q801; R806 120k & R821 150k o/c | 14-09-04 |
| Goldstar | CI14A80 | Reverts to st/by aft few secs | EEPROM 24C04 - does not req preprog chip | 14-09-04 |
| Goldstar | CI14A80 CI14A80F | ORIGINAL TUBE NO LOGER AVAILIABE , ORDER Pt No 205 | C422-0.39uF 20v 181-013C , L402 H.LIN 150-LO2B , R424 6k8 2W ORS6801K607 , FR404 10R 1W ORF0102J607 , C902 270pF OCN2710K519 | 14-09-04 |
| Goldstar | CI14A80F | Dead - chopper Tr BUZ90A s/c | R821 150k o/c also replaced R802 680k; R819 130k; R806 120k - TDA4605-2 may have been damaged but wasn't | 14-09-04 |
| Goldstar | CI14A80F CI20A80F CI21A80F | Dead - Q801 chopper tr s/c | Replace IC801 & check R821 150k & R806 120k | 14-09-04 |
|
|
| Goldstar | CI14A80F CI20A80F CI21A80F | Dead - R802 680k failed | Fit 1w version instead of ?w | 14-09-04 |
| Goldstar | CI14A80F CI20A80F CI21A80F | No tuning or tuner drift | Check Q18 - if no 33v check FR403 - if o/c fit 1R ?w | 14-09-04 |
| Goldstar | CY14A86 | Shuts down aft 30 mins | Sw mode Trfmr had cracked core causing drive chip to overheat | 14-09-04 |
| JVC | C14A1EK | Bright raster with fb lines | FR557 47R 1/2w o/c | 14-09-04 |
| JVC | C14A1EK | Int start up | Dry joint on eyelet which feeds through double sided pcb to R 584 (HT feed to line drive TX). | 14-09-04 |
| JVC | C14A1EK | No st/by but sound muted | replace Q903 (2SA1370), although it tested alright also check R919 & Q902 | 14-09-04 |
| JVC | C14A1EK | NOT SWITCHING TO STANDBY | Q903 ( 2SA1370 ) ALSO CHECK Q902 , 904 | 14-09-04 |
| JVC | C14A1EK | Pic just dims in st/by | Q1901 dry joints or s/c | 14-09-04 |
| JVC | C14A1EK | Sound disappears soon aft sw on | C002 0µ22 50v & resold around jungle chip | 14-09-04 |
| JVC | C14A1EK | St/by only | Q903 2SA1370 st/by sw tr o/c | 14-09-04 |
| JVC | C14A1EK | STUCK IN STANDBY | D581 OPEN | 14-09-04 |
| JVC | C14A1EK | WONT GO TO SBY , JUST DIMS PICTURE | Q1901 s.c. | 14-09-04 |
| Orion | 14ARX | dead | IC101 µchip 5v supply low. C530 3µ3 250v on i/p to 5v reg IC105 u/s | 14-09-04 |
| Orion | 14ARX | Dead 330K start up res ok STR50103 ok R532 hot | Check IC105 ( 5V reg ) & C530 ( 3.3uF ) 250V o/c | 14-09-04 |
| Orion | 14ARX | Dead - R532 2k2 wirewound overheats | C530 3µ3 250v s/c | 14-09-04 |
| Orion | 14ARX | Field rolling | IC401 TA8808N | 14-09-04 |
| Orion | 14ARX | No st/by | C530 3µ3 250v by mains switch | 14-09-04 |
| Orion | 14ARX | St/by only | No 103v HT tho' it did appear initially at sw on. IC401 no volts pin 40 as D403 9v1 zener s/c | 14-09-04 |
| Orion | 14ARX | St/by only | Dis Q117 & if still doesn't come on sus STR50103 or series connected 330k resistors | 14-09-04 |
| Orion | 14ARX | Stuck in StBy H.T. comes up then dies away | Check pin 40 IC401 for 9.1V if missing R458 & D403 | 14-09-04 |