Make | Model | Problem | Solution | Date |
| | | |
Found: 256
|
Akura | CX25/26 | Int field coll | dry joints fop chip & hi watt standoff res near scan coil plug | 14-09-04 |
Akura | CX25/26 | Various inc field, brightness, sound & int dead also rf patt | eeprom chip (can be reprog - need serv man & r/c) - note orig settings b4 adj (see TV mag) | 14-09-04 |
Akura | CX26 | Dead no sec volts from PSU | C812 1µ 50v, C815 220µ 35v, C821 22µ 63v | 14-09-04 |
Akura | CX26 | Field foldover at top | C303 100pF | 14-09-04 |
Akura | CX26 | Int dead/blank raster/txt etc | dry joints on dig sigs pcb links esp link J746 under IC703 | 14-09-04 |
Akura | CX26 | INT FAULTS VARIOUS !! | DRYS ON DIGITAL PCB J746 LINK UNDER IC703 REMOVES LINE DRIVE | 14-09-04 |
Akura | CX26 | Int sw off with line foldover as it goes off | Dry joints line scan coil plug | 14-09-04 |
Akura | CX26 | NICAM OK FM US | IC002 EEPROM US ( SET WILL NEED REPROGRAMMING WITH DEFAULT SETTINGS ) | 14-09-04 |
Akura | CX26 | No fm sound with video pback | fm sound ok at IC101 pin 5 if chip - enters nicam pcb but does not reappear, IC002 eeprom chip faulty | 14-09-04 |
Akura | CX26 | Sound absent | EEPROM | 14-09-04 |
|
Akura | CX26 | St/by only | HT correct (116v) 5v supply low at 1.4v. C841 470µ 16v | 14-09-04 |
Akura | CX26 | Wont go into st/by | R804/805 15k go low res | 14-09-04 |
B & O | 3726 | Black band across pic at sw on | C44, C45 100mfd 63v | 14-09-04 |
B & O | 3726 | St/by only | C29 100mfd 63v | 14-09-04 |
B & O | 3726 | When cold it comes on with the bottom up by 1 inch, slight flyback lines and unlocked
text. The fault clears after 5 minutes, but no amount of freezing will bring it back, you have to switch off for 10 minutes.
| C45 (100µF/40V) which didn't look good
on the ESR meter!
| 14-09-04 |
Beko | 16326NX | Dead/st/by only or partial line coll | C805 330nF 400v dry joints or burnt | 14-09-04 |
Beko | 28426NDS | Problem is ticking BU508df(LOPTr) and flashover on EHTpiller from LOPTX. Can i be informed of any other associated components that would need replacing. The BU508 has destroyed twice.
| you need to replace the lopt and transistor ,then check the line drive frequency-there is a fault which increases the line frequency and there are certain mods which may need to be carried out.
you should have a working set one the lopt and line transistor has been replaced.Try the wimtv site for mor info if you have more problems | 12-12-05 |
Beko | NR26114 | Lack of height with line through | Field scan coils (read 30R) | 14-09-04 |
Beko | NR26114R | Field collapse | R126 4R7 0/c, C113 100n s/c - sm & check TDA3653B | 14-09-04 |
Bush | 2620 | Flashes randomly appear across screen | VR101 AGC preset loose conns | 14-09-04 |
Bush | 2620 | RANDOM FLASHES ON SCREEN | AGC PRESET INT OC | 14-09-04 |
Bush | T26A | Dead - inter ttent. | BU208A , 5D12 ( BY228 ) | 14-09-04 |
Bush | T26A | No raster. | D12 o/c. | 14-09-04 |
Bush | T26A | Sound - no sound or raster. | D10/11 o/c , D12 s/c. | 14-09-04 |
Bush | T26A | Tripping - int. | 7THY2 , 7D12/13 leaky or 7C5 ( 47uf ) | 14-09-04 |
Cathay | TV2600 | Int dead for first 10 mins | 12v reg faulty - used TIP32A | 14-09-04 |
Cathay | TV2610 | L501 resistor smoking | TDA4503 supply feed safety res o/c - 1R5 | 14-09-04 |
Cathay | TV2610 | Line collapse - sound ok | Big boost cap 1µ8 leaky | 14-09-04 |
Dynatron | 267475SK K40 | Takes long time to come on (20 - 30 secs) & no chan nos | Replaced T7123 BC368, T7122 BC369, T7182, T7150, T7162 all BC547, & Chopper tr BU508V & check C2128 100µ & elects in psu pri | 14-09-04 |
Finlandia | C26BZ5 | Tuning store/lock code - press within 5 sec | A,0.Chan-up,Store | 14-09-04 |