| Make | Model | Problem | Solution | Date |
| | | |
| Found: 31
|
| Beko | 28128 | Dead | Chopper Trfmr shorted - found aft many K2545's later | 14-09-04 |
| Beko | 28128 11.1 | No video via scart | TDA8361 | 14-09-04 |
| Beko | 28128NX | Dead & tripping psu | S/C BU508DF LOPTr - when replaced int width variations - caused by wire on Line Dr Trfmr not soldered | 14-09-04 |
| Beko | 28128NX 11.1 | Dead aft smoke | LOPTx u/s 058.541-TR1 R118 10k 0.5W in beam current sensing burnt R110 4.7R 0.5W fusible o/c in +200V supply | 14-09-04 |
| Beko | 2812NX | Field scan partially missing & no tuning | R200 o/c (4R7) and IC200 TDA8170 S/c | 14-09-04 |
| Beko | NR28128NX | Dead & squealing | LOPTx HR8007 approx ?16 | 14-09-04 |
| Beko | NR28128NX | No R/C - front controls ok | No activity around IC951 - chip faulty | 14-09-04 |
| Toshiba | 2112 , 2512 , 2812 | TRIPPING IN ANY MODE | D807 O.C. TYPE BYD33J | 14-09-04 |
| Toshiba | 2112 , 2512 , 2812 | TRIPPING IN NORMAL MODE OK IN STBY. MODE | D813 13v ZENER FAULTY | 14-09-04 |
| Toshiba | 2112 - 2812 - 25 | VIBRATION FROM FRONT OF CABINET | REFIT CHAN - VOL BUTTONS ADDING FELT ALONG THEM | 14-09-04 |
|
|
| Toshiba | 2512DB 2812DB C91SB | Poor width , corrugated effect on side of picture . | C424 4u7 PtNo24676479 | 14-09-04 |
| Toshiba | 2812 | INT TRIPPING | GROUND PIN 52 OF IC501 | 14-09-04 |
| Toshiba | 2812 | Lack of width/tearing | C424 4.7uf 100v on the upright DPC board and C301 | 14-09-04 |
| Toshiba | 2812 | Servive Mode Access | press "F" and the av i/p key ( under the No 7) TOGETHER... then key 1 0 4 8 .. then "F" and green fastext key to move up the menu, "F" and Yellow to move down.. adjust with VOL up/down key | 14-09-04 |
| Toshiba | 2812DB | Brightness excessive - reducing G2 on loptx gives slightly out of focus pic | LOPTx faulty | 14-09-04 |
| Toshiba | 2812DB | Dead | CHECK SOUND O.P. IC. | 14-09-04 |
| Toshiba | 2812DB | DEAD , LOW O.P. FROM P.S. LOOKS LIKE ITS ON S.BY | CHECK D830 OPTO. , IC833 | 14-09-04 |
| Toshiba | 2812DB | Field scan dist until heated | C317 2µ2 | 14-09-04 |
| Toshiba | 2812DB | Horiz band of lines 3" thick | C313 220µ 25v | 14-09-04 |
| Toshiba | 2812DB | in stby after LOPTx and LOPTr 2SC2023 replaced | Q843 2SA1321, Q842 2SC2230 | 14-09-04 |
| Toshiba | 2812DB | Lack of width & line tearing | C424 4µ7 100v in EW mod o DPC board fallen in value | 14-09-04 |
| Toshiba | 2812DB | Line tearing with bands down sides | C424 4µ7 100v under screening can | 14-09-04 |
| Toshiba | 2812DB | Pic shift to left & Q422 on DPC pcb overheats | Dry joint D440 also replaced Q845 st/by tr | 14-09-04 |
| Toshiba | 2812DB | PSU trips one minute after switch one, could be int or random | ground pin 52 of IC501, ref Toshiba technical | 14-09-04 |
| Toshiba | 2812DB | To enter service mode | .Push the "F" & Scart select buttons (red button with arrow though it) together and quickly enter 1048 on remote key pad.
Hold the "F" button until "M" appears at Top right corner of screen.
Select Function with green fast text button & adjust with Volume Up/Down Buttons
Finally store new settings by putting set into standby. | 14-09-04 |
| Toshiba | 2812DBT | Dead & squealing | Loptx overheating - shorted turns | 14-09-04 |
| Toshiba | 2812DBT | Electronic screwdriver settings | Press "F" & "Vid I/P" together to enter menu then selected code '1048'. After few secs "M" appears. Hold "F" & "Pic Menu" buttons to scrollup menu. "F" & "Sound cont" to scroll down. "Vol+/-" buttons adj settings. Use St/by button to store at end. | 14-09-04 |
| Toshiba | 2812DBT | Pic present in st/by (sound muted) | Q845 2SC2023 HT sw tr s/c c-e | 14-09-04 |
| Toshiba | 2812DBT | Poor pic geometry & lack of height/width | electronic screwdriver settings reqd - see database | 14-09-04 |
| Toshiba | 2812DBT | Width narrow | C372 2µ2, C424 4µ7 100v on DPC board (rear right) | 14-09-04 |