Make | Model | Problem | Solution | Date |
| | | |
Found: 39
|
Bush | 2515T | DEAD AFTER REPLACING 270k + 4R7 + CHOPPER TRANSIST | IC803 LM317T 12v REG US | 14-09-04 |
Bush | 2515T | St/by only | IC803 LM317T 12v reg chip | 14-09-04 |
Finlux | 51590 | Trips aft 10 mins | Cu15 100µ 50v | 14-09-04 |
GOODMANS | 5150RC | DEAD | REPLACE C666 150MFD160V | 14-09-04 |
Goodmans | 5150RC | Dead - no HT | C666 150µ 160v | 14-09-04 |
Goodmans | 5150RC | Dead with faint whine/tick | L652 33µ coil HT feed in lop stage dry joints | 14-09-04 |
Luxor | 5151 | Dead. | BU126 , T1A , BRY55 , BC557 , IN4148. | 14-09-04 |
Nokia | 5156 Stereo Plus | No sound or just faint noise | Dis pins 7 & 9 at Nicam module. If sound returns VA60 BC857 & VA61 BC847 are sus (mute trs ) | 14-09-04 |
Philips | 28PW6515/05 | NO raster EHT ok. Int trips if screen volts turned up | D6832 O/C on CRT IN4148 | 14-09-04 |
Philips | 28PW6515/05 | R/C inop | Dry joints on IC7064 solder with care dual layered PCB. | 14-09-04 |
|
Philips | 32pw6515 | hi my philips tv (32pw6515) is now stuck in standby (red led on) and no responce from either the on-board controls or remote?
| the fault on your philips tv is probably ic7064. also known as the painter ic, on the small signal board, this ic seems to be responsible for over 90% of faults on this chassis. it is a 100 pin surface mount device. i would not recommend trying to replace it unless you have a good amount of experience at soldering very small devices as it is not much bigger than a stamp, you will also need to reprogramme the eeprom ic with the options and geometry settings after replacement, i have done more than 30 and it takes me upto 2 hours | 31-10-05 |
Philips | 32pw6515/05 | after set is on for 5 minutes there is no response from remote handset
or controls on tv | Ic 7064 on small signal board.
| 08-08-05 |
Philips | 32PW6515/05 SA10E | Hum from front speaker | Remove link 9710 & connect link from 9710 (C2702 end) to link 9278 | 14-09-04 |
Philips | A10 28PW6515/05 | Reverts to st/by aft several hours until sw off at mains & re-started | IC7064 micro | 14-09-04 |
Philips | A10E 28PW6515/05 | Random variation of width/height with pic jumping | Painter micro chip faulty | 14-09-04 |
Philips | MG2.1E 28PW9515/05 | Dead with LOPTr s/c - BU2520DF | For reliability do following mod - remove C2411, change C2413 to 10µ 100v, R3406 to 100R to alter line dr coupling from ac to dc | 14-09-04 |
Saba | M5515 | Poor start up | CP59 1000µ | 14-09-04 |
Samsung | CI515ZA | Int blowing fuse. | Replace 800mA with a 1AT anti-surge type. | 14-09-04 |
SANYO | CB5153 | DEAD | Q432 S/C CPC*SC2SD1651 | 14-09-04 |
Sanyo | CB5156 | Dead - trips once with snatch of sound | LA7832 fop chip s/c, R364 4R7 2w hi res (24v feed); D351 dry joints | 14-09-04 |
Sanyo | CB5156 | Thin dark vertical line on the left side of the picture | R433 DJ, located next to the SCART socket | 14-09-04 |
Sanyo | CB5159 C21EF35NB | Dead | IV451 LA7832 FOP chip s/c, R364 4R7 ?w fusible o/c, C362 22µ 250v 180v smoother s/c, D351 dry joint | 14-09-04 |
Sanyo | CB5159 C21EF35NB | No sound | Q2961/2962 2SC812L6 sm on nicam pcb both faulty- used BC846B in lieu, TDA7263 AF o/p chip u/s | 14-09-04 |
Sanyo | CB5159 C21EF35NB | No Txt | No 5v (REF+) pin 6 IC1001 Txt dec chip SAA5281P/E- D1001 5v1 zener leaky | 14-09-04 |
Sanyo | CBP5156 | No chan OSD, vol bar stops ? way across & no B in Txt | Dry joints IC001 SAA5246 Txt proc chip | 14-09-04 |
Sanyo | EC3 CB5153 | dead | Q432 2SD1651 s/c | 14-09-04 |
Sanyo | EC3 CB5156 | drifts off tune | replace C105 1uF 50V near tuner | 14-09-04 |
Sanyo | EC3 CB5156 | when switched on from stby, the set immediately reverts back to stby | in protection mode (pin 31 IC701 below 5V) due to R327 390k o/c | 14-09-04 |
Sharp | DV5131H DV5150 | NO CHROMA AFTER CHAN. CHANGE OR SLOW TO LOCK AFTER | ADD 8.2M RES. BETWEEN PINS 25 - 39 OF IC801 | 14-09-04 |
Sharp | DV5150 | COMES ON BUT GOES STRAIGHT TO STBY | R612 OC CHANGE TO 2R2 REPLACE WIRE LINK J13 WITH 1R2 RESISTOR Pt No s -XZ0204BMZZ VRD-RA2HD1R2J | 14-09-04 |