Make | Model | Problem | Solution | Date |
| | | |
Found: 97
|
Ferguson | ICC9 - DPL | Height reduced, menus wrong, no pic, search tuning erratic etc | Select serv mode & set up the 3 menus to factory default then reset menus - see full explanation by Dave Hewitt | 14-09-04 |
Ferguson | ICC9 - DPL | Service mode - entering | Sw on ac mains whilst pressing blue txt button then press blue button again. Exit set up by pressing 'st/by' | 14-09-04 |
Ferguson | ICC9 T28DPL | Goes to st/by when vol adj (local or R/C) | EEPROM - ST24C04CB1 | 14-09-04 |
Ferguson | ICC9 T28DPL | Int lock up of controls on TV & R/C | IR01 micro - fit new type ODX6734001 | 14-09-04 |
Ferguson | ICC9 T28DPL | Line osc speed out | IV01 STV2160 | 14-09-04 |
Goodmans | 2850DPL | Blank raster & flyback lines, sound & osd ok | CK53 12µ 63v in LOP stage | 14-09-04 |
Goodmans | 285DPL | "Put put" noise in st/by | WA21 zero ohm link on Dolby module - remove it | 14-09-04 |
Goodmans | 285DPL | Arcing effect on pic, int field & blanking out | Dry joint LOPTr heatsink | 14-09-04 |
Goodmans | 285DPL | ARCING ON PICTURE | RESOLDER LINE O/P TRANSISTOR HEAT SINK | 14-09-04 |
Goodmans | 285DPL | BLANK RASTER WITH SOUND | REPLACE C416,R409,R503 AND D506 | 14-09-04 |
|
Goodmans | 285DPL | Dead - no sec volts after psu rebuild - LED rapid flash | C012 10µ 25v s/c - removes start & run supply to N010 pin 16 | 14-09-04 |
Goodmans | 285DPL | DEAD WITH STANDBY LIGHT FLASHING | REPLACE RK68 AND VK71 | 14-09-04 |
Goodmans | 285DPL | E/W dist with lack of width | RK62 not soldered properly | 14-09-04 |
Goodmans | 285DPL | E/W dist with lack of width | RK62 15R o/c, NS10 TDA8350Q faulty - check V508 diode lead hasn't s/c to RK62 | 14-09-04 |
Goodmans | 285DPL | EHT COMES UP THEN SET SHUTS DOWN | SUSPECT LOPTX | 14-09-04 |
Goodmans | 285DPL | Field collapse | TDA 8350Q and RK68 10R fusible both blown part no JVC*TPCE0051for chip - must use correct version of chip - cheapest at CHS | 14-09-04 |
Goodmans | 285DPL | Field collapse | TDA8350Q, RK68 10R 1/2w & C069 220µ 35v | 14-09-04 |
Goodmans | 285DPL | Focus out with ticking from focus unit | Dry joint RK61 5M6 | 14-09-04 |
Goodmans | 285DPL | Lack of height | FOP chip & RK68 1R feed res | 14-09-04 |
Goodmans | 285DPL | LACK OF WIDTH WITH E/W DISTORTION | CHECK RK62 FOR DRY JOINTS | 14-09-04 |
Goodmans | 285DPL | LED flashes 3 times ata sw on then dead | VK71 BYW32 s/c & NS10 TDA8350Q s/c | 14-09-04 |
Goodmans | 285DPL | LED FLASHES 3 TIMES THEN STAYS ON SET DEAD | REPLACE VK71 AND NS10 | 14-09-04 |
Goodmans | 285DPL | No or int col | CD37 22nF 25v sm leaky - pin 6 ND10 or CD15 270pF sm pin 33 ND10 | 14-09-04 |
Goodmans | 285DPL | No pic - blank raster if A1 advanced | CK53 0µ12 in LOP | 14-09-04 |
Goodmans | 285DPL | No pic or OSD - Txt headings at bottom - sound ok | Flyback pulses to pin 39 ND10 jungle IC dist - CK53 120nF near LOPTx | 14-09-04 |
Goodmans | 285DPL | No sound | NA90/40 s/c TDA2615 & RA24 1R o/c | 14-09-04 |
Goodmans | 285DPL | NO SOUND FROM HEADPHONE SOCKET | CHECK HEADPHONE LEVEL IN SOUND MENU | 14-09-04 |
Goodmans | 285DPL | No sound from phone skt | Check sound options menu | 14-09-04 |
Goodmans | 285DPL | POWERS UP THEN GOES TO STANDY | VK67 ON PIN 3 OF LOPTX S/C | 14-09-04 |
Goodmans | 285DPL | PUTTING NOISE ON STANDBY | REMOVE LINK WA21 ON DOLBY MODULE | 14-09-04 |