Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....
◦
register
◦
send pass
S
earch
B
rowse
U
pload
W
anted
D
atasheets
C
hassis2model
R
epair tips
F
ulltext search
C
ables & Connectors
R
epair tips
Electronic appliance repair tips database - TV (LCD,TFT,Plasma,Digital), Monitor, VCR, DVD recorder and player, Digital camera, Audio equipment, Microwave ovens, Phone systems, Computer repair
Make
Model
Problem
Solution
Date
Found: 11
JVC
AV-14FM
G3
B
JVC Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off.
Resold the vertical I/C. You have dry joints on that part.
29-06-05
JVC
AV-14FM
G3
B
Jvc Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off. what can be the fault.
Could you check if there is any voltage e.g. on the collector of the high voltage transistor? A blinking power-led, is usualy indicating a problem on the secundairy side of the power supply! So try to obtain a diagram and meassure these voltages.
02-07-05
Panasonic
Euro 7 TX32P
G3
0
St/by only
Reset line volts going into U1 pcb stuck halfway - being loaded by faulty sm filter LC1118 in reset line
14-09-04
Philips
M
G3
.1EAA 28PW9525/05
Sound dist/fuzzy
Hi imp center speaker
14-09-04
SEG
CT7951
G3
11AK19P
Dead
R817 5w 2R2 o/c, Q802 2SK2545 chopper Tr s/c, D805 BA159 & UF5407 diode
14-09-04
Sony
G3
F KVK29SN21
Reverts to st/by with no sound/pic
LOPTr Q2591 2SC4927 s/c due to dry joints T2502 line dr tx & R886 1.2e 3w o/c in psu
14-09-04
Thomson
ICC19 28D
G3
5UB
Int shows pic but usually error code indicating faulty Txt
Replace Txt panel
14-09-04
Thomson
ICC19 28D
G3
5UB
PIN code unsetting - "Type in 4 digit code" message
Hold down both prog & vol minus(-) button on TV & switch on. Release buttons & you should be in service mode.Navigate with arrow buttons on remote to "Setup" then select "Erase Pin" by holding down the right arrow button for 5 secs until yellow tick appears in box.You must backtrack to find the "Quit" option to exit & store the new info.
14-09-04
Thomson
ICC19 28D
G3
5UB
Tuning mode
From st/by hold down menu button & the set will turn on in preset mode. Follow on screen prompts
14-09-04
Thomson
ICC19 28D
G3
5UD
Dead with led flashing
unplugging Dolby module restored pic. TDA2615 amp chip IS450 blasted - pt no 10257880
14-09-04
Toshiba
28MW7DB/G 32MW7DB/G
Freeze frame of noise/no sync/slo-mo pic etc
VD pulse o/p pin 31 IC501 low amplitude (0.9v p-p instead of 5v p-p). IC501 Q501 part no B0385990 faulty
14-09-04
page:
1
FB
-
Links
-
Info / Contacts
-
Forum
-
Last SM download : Matsui 1410R_T
script execution: 0.23 s