Make | Model | Problem | Solution | Date |
| | | |
Found: 27
|
Ferguson | ICC6 | Blank raster | TA7550 in IF can | 14-09-04 |
Ferguson | ICC6 | Chans int scroll through | Membrane touch panel sus | 14-09-04 |
Ferguson | ICC6 | dead - line driver tr TL31 faulty | you must o/c pin4 IC IR81 to stop tv from tripping | 14-09-04 |
Ferguson | ICC6 | DEAD NO STBY LIGHT , POWER SUPPLY OK | RP04 OC ( NO UA SUPPLY TO AUDIO IC ) | 14-09-04 |
Ferguson | ICC6 | Field bounce dependent on pic content | Incorrect biasing of TP06 on Text PCB Fit RV02 ( 1M ) PtN 90256500 | 14-09-04 |
Ferguson | ICC6 | Field jitter | TV71 sm BC858 | 14-09-04 |
Ferguson | ICC6 | Horiz jitter | BC858 sm TV71 leaky | 14-09-04 |
Ferguson | ICC6 | int scroll thro chans | keyboard foil | 14-09-04 |
Ferguson | ICC6 | int start up | CP29 470µ 16v chopper base coupling cap | 14-09-04 |
Ferguson | ICC6 | Lack of brill (OSD at max) | fit 5k6 res in parallel with RR48 (not official mod) | 14-09-04 |
|
Ferguson | ICC6 | Line twitch getting worse as heated | TV71 BC858B in line pulse feedback - checks ok out of cct | 14-09-04 |
Ferguson | ICC6 | LOPTx replacement | Check that it isn't likely to short to wire links underneath | 14-09-04 |
Ferguson | ICC6 | LOW IF GAIN | CS25 1mfd CAP ON PIN 13 OF LA7550 IC IS10 IN IF MODULE | 14-09-04 |
Ferguson | ICC6 | No G2 volts | C814 | 14-09-04 |
Ferguson | ICC6 | No raster until A1's advanced then blank | dry joints around loptx | 14-09-04 |
Ferguson | ICC6 | No video o/p intermit | TV92 BC858B sm | 14-09-04 |
Ferguson | ICC6 | Removing child lock | 1 switch to standby
2 switch off with mains and let light go out
3 switch on mains while holding standby on remote for 6 secs
4 a red key shows it is locked ,toggle on/off with +/- buttons on remote | 14-09-04 |
Ferguson | ICC6 | sizzling sound from lopt | LOPT replaced | 14-09-04 |
Ferguson | ICC6 | St/by only - LED flashes | Dis pin 4 from reg IC TDA8139 (Dis prot) brought up blank raster with no OSD, fitted new proc original is type ST6393B1/ZM, but the Seme CD advises using ST6397BB1& replace TDA8139 reg which was also faulty | 14-09-04 |
Ferguson | ICC6 | Trips 9 times then dead | TL90 BC848B & TF01 BC848B in beam lim faulty tho check ok out of cct | 14-09-04 |
Ferguson | ICC6 | When playing MACRO encoded tapes AV time constant | Replace CV86 with ( 8.2nF ) & RV64 with ( 12K ) & RV66 with ( 15K ) | 14-09-04 |
Ferguson | ICC6 | Very dark picture (All Cathodes measured 190volts | TB11 (BC557 on CRT Base) | 14-09-04 |
Ferguson | ICC6 C51F | LOPTx arcing | Replace LOPTx HR7269 resulted in 2 x RGB o/p Trs damaged BF871 & G2 cap 10,000pF 3kv leaky & TB11 BC557C on crt base | 14-09-04 |
Ferguson | ICC6 C51F | Bright raster with fb lines aft LOPTx replacement | RL11 (15r fusible) immediately behind the lopt | 14-09-04 |
Ferguson | ICC6 C51F | Service mode entering | Put the TV into stby.then switch off at mains... wait until the stby led goes completely out. switch on at the mains whilst holding down the Blue fastext key on the r/c. let the key go when TV comes on . the n press the Blue key again and a menu will come on screen.
Vol +/- moves menu sideways. the Blue key moves down the menu. vol +/- alters the values...scroll all the way down the menu to find "store" to keep
changes.remove mains to get out of menu." | 14-09-04 |
Saba | 6317 ICC6 | No sound | Replace TV86 SMD transistor. | 14-09-04 |
Thorn | ICC6 C51T | No pic - blank raster with fb lines - sound ok; OSD OK if A1 advanced | Replace TV92 (BC858B) surface mounted transistor | 14-09-04 |