| Make | Model | Problem | Solution | Date |
| | | |
| Found: 26
|
| Bush | 2871NTX 11AK19-P4 | No pic or OSD - sound present | TDA6108JF on the CRT base | 14-09-04 |
| Bush | WS6671 11AK19P4 | Narrow pic | R629(2R7 1/3 watt fusible) plus DJ on C630. | 14-09-04 |
| Bush | WS6671 11AK19P4 | Narrow pic | Dry joint/ o/c C630 560n; R629 27R? Safety o/c, L604 reads 3R (correct), Q603 PHF9NQ20T replaced - used BUK444 200A in lieu | 14-09-04 |
| Bush | WS6671 11AK19P4 | Width excessive | Q603 (9NQ20T or BUK444-200 or MTP6N60E) | 14-09-04 |
| Bush | WS7671 11AK19P4 | Dead - off with a bang | IC802 MC44604P, IC801 CQY80NG CNX82 OR SEME TYPE OPT403 OPTOCOUPLER, Q802 2SK2545 MTP6N60E, R822 22K 3W, D807 RL207 BA159, D826 BA159, D827 BA159, D824 MR852 BYW98/200V | 14-09-04 |
| Daewoo | CP420 GB14F7T1 | Int reverts to st/by | RLY2 relay was operating when fault occurred - IC I807 (TOP210-PF1) the standby switch mode IC in the power supply | 14-09-04 |
| Daewoo | GB14F7T1 CP420 | St/by only | R804 47k start up res | 14-09-04 |
| Ferguson | RP46 | Dead - st/bt led comes on briefly & buzzing from chopper tfmr | Overload on lop caused by EHT splitter shorted | 14-09-04 |
| Ferguson | RP46 (Proj TV) | No Red | R615 [910K] open circuit - in series with the red A1 preset | 14-09-04 |
| Ferguson | RP46 (proj) | Red pic at sw on then shuts down | RG18 680k on sub G2 board o/c | 14-09-04 |
|
|
| Ferguson | RP46 (proj) | Vol level varies on its own | CR11 o/c - near IR01 | 14-09-04 |
| Ferguson | RP46 rear proj | No convergence | RP09 100k or RP18 220k o/c in conv psu near blue tube | 14-09-04 |
| Goodmans | TVC141 CP420 | Focus & screen adj faulty - looks like CRT | I501 TDA8374A | 14-09-04 |
| Grundig | P45-440/1GB | No pic - sound ok - faint arcing noise | dry joints ww res R516 in line stage | 14-09-04 |
| Grundig | TP400TT Hand Set | Few flashes then nothing. | 470uf , 8v. | 14-09-04 |
| Nokia | MP45H1 | No tuning | Tuner faulty pt no AKAI58231008 | 14-09-04 |
| Panasonic | TX14GV1 Daewoo CP421 | Relay clicking No sound or vision | Check C840 47mfd and I807 TOP210PFI | 14-09-04 |
| Samsung | CB536Z P45S | Rolls aft 2 hrs | R210 240k | 14-09-04 |
| Sanyo | CE28WP4 | E/W & excess height | Fit geometry mod kit pt no B10H04DOL & reset PROM values | 14-09-04 |
| Sanyo | CE28WP4 | Tuning won't stop in search & slow to tune in manually | Slight tweaking of AFC coil L171 | 14-09-04 |
| Sharp | 12P-41H | No pic - crt htrs lit - no EHT | LOPTx | 14-09-04 |
| Sony | RE-1 KP41S3 | dead, set in trip mode due to no frame | DJ on R1507 on D board | 14-09-04 |
| Sony | RE-1 KP41S3 | int no display, sound Ok | no -12V supply on E board, IC905 12V regulator u/s (875992965) | 14-09-04 |
| Sony | RE-1 KP41S3 | poor sound quality, hissing | wrong standard is set (5.5MHz), enter tuning menu, enter each channel individually and select 'system change', change to PAL I and press ENTER to store | 14-09-04 |
| Thomson | RP46 | Tripping - EHT splitter faulty, new one has short life | R18 220k hi res & check R9 100k 2w | 14-09-04 |
| Various | 11AK19P4 | E/W corr faulty - no o/p pin 45 TDA8844 | Apply 5v to pin 45 & blow leaky diode | 14-09-04 |