Make | Model | Problem | Solution | Date |
| | | |
Found: 70
|
JVC | AV-14FMG3B | JVC Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off. | Resold the vertical I/C. You have dry joints on that part.
| 29-06-05 |
JVC | AV-14FMG3B | Jvc Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off. what can be the fault. | Could you check if there is any voltage e.g. on the collector of the high voltage transistor?
A blinking power-led, is usualy indicating a problem on the secundairy side of the power supply!
So try to obtain a diagram and meassure these voltages.
| 02-07-05 |
Mitsubishi | 21AV1BD | No pic (blue screen) or sound | Refitting a loose plug and soldering dj's on the dolby panel & replacing the onboard output IC TDA7263 and it's safety resistor gave a good picture with a loud hiss instead of sound. Go into service mode & reset eprom data to get sound back. | 14-09-04 |
Mitsubishi | 25AV1BDS | dead/tripping led flashing | replace C702 1000µ 6.3v with 10µ & C955 2200µ 16v with 3300µ & do a reset (sw on whilst holding reset button in (near tuner)) & set up eeprom options | 14-09-04 |
Mitsubishi | AV1 M5 srs | Memory keeps getting corrupted . | Change R213 , R214 and ( M5 - R746 ) , ( AV1 - R702 ) from 220R to 1K . On M5's only ( and if not already done ) add a 5v6 ze | 14-09-04 |
Mitsubishi | AV1 srs | RF PATTERNING ( SIMILAR TO VIDEOCRYPT ) | FIT RF LEAD Pt No H24P001010 | 14-09-04 |
Mitsubishi | AV1 srs | RGB OUTPUT SC ( IC660 TEA5101B ) | CHECK FOR 12v ON WIRE LINK TO PIN 2. IF MISSING OR LOW PICTURE WILL BE AWFUL AND A1 WILL NOT SET COECTLY. Q6E8 LEAKY. REPLA | 14-09-04 |
Mitsubishi | AV1 srs | Tuning drift . Fit previous mod if not done alread | Change R120 , 121 ( 56k ) to 18k , remove R736 ( 22k ) and fit an 8k2 & 15k 1/6w R-Metal in series . Make sure AFT is ON . | 14-09-04 |
Mitsubishi | AV1 srs ( 2 | POOR PICTURE . | CHANGE R521 FROM 82k TO 56k AND FIT ZENER DIODE KIT , Pt No 264P45090 | 14-09-04 |
Mitsubishi | AV1 srs WITH SAT | BLANK RASTER OSD OK. | Z953 1.6A OC DUE TO LNB SHORTED - UPRATE TO 3.15A Pt No 299P193030 | 14-09-04 |
|
Mitsubishi | C28AV18 | No sound aft customer had been trying to "tune" | Reprog EEPROM - sound setting should be either 10 or 2 if 10 is not poss | 14-09-04 |
Mitsubishi | CT21AV1 CT25AV1 | Failure of Q552 | Order & fit AVM5KIT | 14-09-04 |
Mitsubishi | CT21AV1 CT25AV1 | Tuning drift mainly at top end of band | Add ( 180K ) & Diode ( IN4148 ) in series cathode of diode to 5V pin 6 Tuner & res to Tuning Voltage line pin 2 | 14-09-04 |
Mitsubishi | CT21AV1B | Line collapse | R910 100R 1w, C901 (marked as C5D3) 470n 400v & resolder dries in the area | 14-09-04 |
Mitsubishi | CT21AV1B EE3 | Dead - psu fault | Q952 s/c D957 s/c Z953 o/c - mod kit 8VREG-KIT available if Q952 u/s | 14-09-04 |
Mitsubishi | CT21AV1B EE3 | Dead with green LED lit | PSU running but no line drive - mod = C702 from 1000mfd to 10mfd 25v, check C955 is 3300mfd 16v. Replace R702, 213, 214 with 1k 1/4w | 14-09-04 |
Mitsubishi | CT21AV1BS | col level int | Q704 JC501 blanking tr on main pcb | 14-09-04 |
Mitsubishi | CT21AV1BS | Dead | All psu o/ps ok but no line drive - IC ST24C08 memory IC | 14-09-04 |
Mitsubishi | CT21AV1BS | St/by only | C955 2200µ sec psu hi esr | 14-09-04 |
Mitsubishi | CT2525AV1BD | E/W faulty | L504 shorted turns - Pt no MITS409P749010 | 14-09-04 |
Mitsubishi | CT25AV1 | No pic or OSG - sound ok | 12v Sw Tr on CRT Base o/c b/e (feeds 12v to
TDA 5105 RGB drive I.C. PIN 2.) | 14-09-04 |
Mitsubishi | CT25AV1 EE3 | Dead - LOPTr leaky | TEA2031A E/W corr chip s/c | 14-09-04 |
Mitsubishi | CT25AV1 EE3 | Dead - no line drive | Q501 JC501-R faulty - 2SC1815 used as replacement | 14-09-04 |
Mitsubishi | CT25AV1B | INT NO SOUND | REPLACE REGULATOR MOD KIT AND IC202 | 14-09-04 |
Mitsubishi | CT25AV1B | Sound int | IC202 TEA6415C faulty (draws excess current) & replace 8v reg Pt no MITS8VREGKIT | 14-09-04 |
Mitsubishi | CT25AV1BD | Field collapse | D561 s/c on E/W IC & R516 o/c | 14-09-04 |
Mitsubishi | CT25AV1BD EE3 | Blank raster with no sound or osd | No 8v - fit kit 8vREG-KIT from SEME | 14-09-04 |
Mitsubishi | CT25AV1BD EE3 | Dead - Green LED lit | change C702 to 10uf & C955 to 3300uf also change R702 R213 & R214 from 220R to 1k & reset eeprom | 14-09-04 |
Mitsubishi | CT25AV1BD EE3 | Dead - LOPTr s/c | TEA2031A E/W chip IC551 faulty, R510 100R 2w overheating due to L501 6800uH shorted turns | 14-09-04 |
Mitsubishi | CT25AV1BDS | Service mode & EEPROM settings | Switch on with mains switch and press service microswitch, select button 9 on the remote within 5secs. You will now be in the service mode. Use the buttons on the remote control for the following adjustments:
* to toggle between adjustment displays
1 cancel; 2 increase adjustment code; 4 decrease data value; 6 increase data value; 8 decrease adjustment code; 9 adjustment mode on; 0 write to the eeprom( press this to write your changes to the eeprom)
Here are the options-
TUN 0; SAT 1; AUD 10; ATS 1; STD 1; SYS 1; AV1 2; EEX -; SPK 1; EEP -; ABG 02; A1 02;AL 00; ADK 15; MNP 70; TXT -; FFT 1; VOL 74;HYP 1; SCP 20; FMP 23.
not all options appear to be available to some models. Adjustments in the VCJ mode will be in default mode and it will be necessary to observe display in order to set-up width height ew etc. | 14-09-04 |