Make | Model | Problem | Solution | Date |
| | | |
Found: 127
|
Ferguson | D59N (ICC9) | INT WON'T COME OUT OF STANDBY | REPLACE IP03 9V REG | 14-09-04 |
FERGUSON | D59N (ICC9) | NO SYNC ON SCREEN GRAPHICS | REPLACE TR42 BC848 (SMD) | 14-09-04 |
Ferguson | D78N (ICC9) | PULSING RED/GREEN LED | CHECK SMD DIODE DP83 OFF PIN1 OF IP03 | 14-09-04 |
Ferguson | ICC9 | Black vert line rises & falls like bargraph when heated | CL21 12n5 1600v flyback tuning cap (read more or less ok) | 14-09-04 |
Ferguson | ICC9 | Blank raster with flashing until warm | TC03 BC858 sm in video path leaky | 14-09-04 |
Ferguson | ICC9 | Blank screen, low video o/p at scart | LA7550 IC in IF module - check TH01 sm tr signal for saturation | 14-09-04 |
Ferguson | ICC9 | Bounce may be int & only on video channel. | Change res RV02 ( SMD ) to 1meg under Tx PCB. | 14-09-04 |
Ferguson | ICC9 | Buzzing/ghosting - int | Check elects in IF unit & dry joints on tuner earths | 14-09-04 |
Ferguson | ICC9 | Dead | CL24 0µ33 250v by LOPTr bulging, o/c & dry jointed, S2000AF-1 LOPTr s/c | 14-09-04 |
Ferguson | ICC9 | Dead - lop tr s/c | No pic when replaced - low drive at lop tr base, DL61 1N4001 o/c on load | 14-09-04 |
|
Ferguson | ICC9 | Dead - TL19 lop tr BUH517TH s/c | Replacement got hot - replace TL61 line dr tr 2SC2655 | 14-09-04 |
Ferguson | ICC9 | DEAD , ONLY HT ( 165v ) LOPT. | CHECK FIELD IC TDA8172 | 14-09-04 |
Ferguson | ICC9 | DEAD , STARTS BUT SHUTS DOWN | CHECK FIELD CHIP TDA 8172 NOT TDA8178 , WILL WORK BUT SHOWS FLYBACK LINES | 14-09-04 |
Ferguson | ICC9 | Dead due to LOPtr failure - gets hot quickly | 6 x 1N4001 diodes in base drive - 1 was faulty - replace all | 14-09-04 |
Ferguson | ICC9 | E/W dist | CL42 4µ7 160v | 14-09-04 |
FERGUSON | ICC9 | E/W DISTORTION | REPLACE CL42 4.7MFD160V | 14-09-04 |
Ferguson | ICC9 | Field jumping | 25Hz wfm at pin 20 IV01 STV2160where ther should be none - CV11 100nf o/c | 14-09-04 |
Ferguson | ICC9 | goes to st/by when sw on | TDA2616 sound chip | 14-09-04 |
Ferguson | ICC9 | Int dead | Supply to line drive chip IV01 STV2160 drops in fault condition (no line drive) - DV01 1N4001 int | 14-09-04 |
Ferguson | ICC9 | Int dead | dry joints IP03 reg | 14-09-04 |
Ferguson | ICC9 | int line sync when heated | STV2160 chip IV01 - change CV46 to 33n | 14-09-04 |
Ferguson | ICC9 | Int picture. | 27Mhz XTAL TEXT BOARD | 14-09-04 |
Ferguson | ICC9 | Int sigs/snowy - tap sensitive | TC03 BC858B sm | 14-09-04 |
Ferguson | ICC9 | Int sw off with black line down centre of screen when heated | C123 - cap near scan coils | 14-09-04 |
Ferguson | ICC9 | Int trip with failure of LOPTr | RV01 10R safety res gone hi - next to STV2160 IV01 | 14-09-04 |
Ferguson | ICC9 | Int trip/dead with led flashing or absent | TP78 BC848B in trip cct | 14-09-04 |
Ferguson | ICC9 | Int won't come out of st/by | T66 (BC858 smd) was leaky | 14-09-04 |
Ferguson | ICC9 | lop tr gets hot quickly - then blows | TL61 2SC2655 line dr faulty tho checked ok | 14-09-04 |
Ferguson | ICC9 | LOPT s/c New gets hot | Check DL61 ( IN4001 ) feeds 7.5V to line drive | 14-09-04 |
Ferguson | ICC9 | low contrast - line tearing | TX16 BC858 leaky b-e | 14-09-04 |