Make | Model | Problem | Solution | Date |
| | | |
Found: 98
|
Beko | 28426NDS | Problem is ticking BU508df(LOPTr) and flashover on EHTpiller from LOPTX. Can i be informed of any other associated components that would need replacing. The BU508 has destroyed twice.
| you need to replace the lopt and transistor ,then check the line drive frequency-there is a fault which increases the line frequency and there are certain mods which may need to be carried out.
you should have a working set one the lopt and line transistor has been replaced.Try the wimtv site for mor info if you have more problems | 12-12-05 |
Beko | NR28416NDS | Dead aft thunderstorm | IC601 (MC44608P40), T601 (2SK2545) R606/607 (0.47R, 1/2W) in psu replaced | 14-09-04 |
Beko | NR28416NDS | Dead with LOPTx insulation breakdown | LOPTx Pt no 058834-TR2 | 14-09-04 |
Ferguson | DSF68NX | Patterning on pic & hum on sound until heated | CG03 4µ7 100v behind LOPTx | 14-09-04 |
Ferguson | IDC2 DSF68N | Int comes on or reverts to AV2 | TX26 BC858B sm | 14-09-04 |
Ferguson | IDC2 DSF68N | No mono sound | EEPROM | 14-09-04 |
Ferguson | IDC2 DSF68N | No sound - pic ok | TS40 BC857 in audio mute cct | 14-09-04 |
Ferguson | IDC2 DSF68N | Sound int | Audio muted - pin 4 Plug BS80 high - TS41 BC857B faulty | 14-09-04 |
Goodmans | 205N Goldstar | Sound muted | Q805 in psu near chopper Tx leaky 2SA1266 - fitted 2SA1013 in lieu | 14-09-04 |
Hitachi | CPT2288DS | St/by only | No o/p from sw mode PSU as LL04 coil o/c | 14-09-04 |
|
Hitachi | CPT2288DS | Standby - LED on - dead. | LL04 o/c - may be able to unwind & refit. | 14-09-04 |
Mitsubishi | 25AV1BDS | dead/tripping led flashing | replace C702 1000µ 6.3v with 10µ & C955 2200µ 16v with 3300µ & do a reset (sw on whilst holding reset button in (near tuner)) & set up eeprom options | 14-09-04 |
Mitsubishi | BDS1451UK 11AH20-S | St/by only | Check D604 BA157 LH side of LOPTx & R/C is initialised after batt change - Initialise remote by pressing arrow L arrow R and arrow Down as well as
number 1 at the same time | 14-09-04 |
Mitsubishi | BDS1451UK 11AK20-S | St/by only | Replaced IC501 (ST92195B1B1) Micro & check 4Mhx Xtal | 14-09-04 |
Mitsubishi | BDS21S | Dead - no st/by LED & HT 90v approx | C289 47uf 160v | 14-09-04 |
Mitsubishi | BDS28WS 11AK19 | Dead apart from LED dimly flashing green - will sw on & off - no EHT & HT (150v) low at 102v | D807 in psu leaky | 14-09-04 |
Mitsubishi | BDS28WS 11AK19 | Entering service mode | first enter the installation menu, then press 4, 7, 2 & 5 respectively (another possibility is 2,3,5,7) | 14-09-04 |
Mitsubishi | BDS28WS 11AK19 | Int blows LOPTr at sw on - also EW FET & R629 could be damaged | Dry joint C630 | 14-09-04 |
Mitsubishi | BDS28WS 11AK19Pro | Int shuts down to st/by with LED dimming - usually at start up | Focus spark gap arcing - replaced CRT skt 30001855 ?1.39 from SEME | 14-09-04 |
Mitsubishi | BDS28WS11AK19PRO | Dead | Q605 BU2508AF, C630 390NF 250V, C626 12NF 2000V, L604 E/W Coil, TR601 Line drive transformer, L604 15mH Coil, R629 27R, D807 BA159, D605 BA159, D606 BA159, C835 1nF 1000V | 14-09-04 |
Mitsubishi | BDS28WS11AK19PRO | Sw to st/by aft 2 mins - G LED flasheswhen trying to come out of st/by | D505 2v4 zener sm conn to pin 33 IC501 leaky | 14-09-04 |
Mitsubishi | BDS28WS11AK19PRO | Won't come out of st/by when sw to st/by aft operating for more than 5 mins | Sw mode Tr replaced | 14-09-04 |
Mitsubishi | Black Diamond BDS1451UK 11AK20-S | St/by only | Check 4Mhz Xtal by micro - may be dry jointed | 14-09-04 |
Mitsubishi | CT25AV1BDS | Service mode & EEPROM settings | Switch on with mains switch and press service microswitch, select button 9 on the remote within 5secs. You will now be in the service mode. Use the buttons on the remote control for the following adjustments:
* to toggle between adjustment displays
1 cancel; 2 increase adjustment code; 4 decrease data value; 6 increase data value; 8 decrease adjustment code; 9 adjustment mode on; 0 write to the eeprom( press this to write your changes to the eeprom)
Here are the options-
TUN 0; SAT 1; AUD 10; ATS 1; STD 1; SYS 1; AV1 2; EEX -; SPK 1; EEP -; ABG 02; A1 02;AL 00; ADK 15; MNP 70; TXT -; FFT 1; VOL 74;HYP 1; SCP 20; FMP 23.
not all options appear to be available to some models. Adjustments in the VCJ mode will be in default mode and it will be necessary to observe display in order to set-up width height ew etc. | 14-09-04 |
Mitsubishi | CT25AV1BDS EE3 | Int blows LOPTr at sw on from cold & lack of height/int contrast from cold | C956 6.3V 470uF in 5V supply. | 14-09-04 |
Mitsubishi | CT25AVBDS EE3 | Int sw on/ off - G LED lights but no pic/sound (no line drive) | C956 470uF 6.3v in secondary power supply circuit, close to IC951 | 14-09-04 |
Mitsubishi | CT25AVIBDS | Slow startup. | Change C955 ( 2200uf ) | 14-09-04 |
Mitsubishi | CT28AV18DS | Blank raster & no sound - int comes on but if turned off will not come back on | Dry joints IC951 reg (no supply to micro) | 14-09-04 |
Mitsubishi | EE3 CT25AV1BDS | Herringbone pattern, flashing lines etc with no pic for 5 minutes. Picture then slowly appears | C956 470uF 6.3V | 14-09-04 |
Philips | 29DS100 | Unable to switch channel from Pr1 to Pr2. | Check and replace if necessary position 7002 on the SSP into MG21A11.6_01901 (3104 317 41901)
IRIS CODE : 1272 | 14-09-04 |