onkyo dpc-5.3 free download

File name onkyo DPC-5.3.pdf

DPC-5.3 Ref. No. 3736 SERVICE MANUAL Sep, 2002 DVD CHANGER MODEL DPC-5.3 DISC SKIP Black model BUDD 120V AC, 60Hz RC-503DV SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. www.denom.com DPC-5.3 SPECIFICATIONS DVD Changer Power supply Power consumption Weight External dimensions Signal system Frequency range (digital audio) Signal-to-noise ratio (digital audio) Audio dynamic range (digital audio) Harmonic distortion (digital audio) Wow and flutter Operating conditions AC 120 V, 60 Hz 20 W 15.0 lbs 17 1/8" x 5 1/16" x 16 15/16" (W/H/D) NTSC 48 kHz sampling 4 Hz to 22 kHz 96 kHz sampling 4 Hz to 42 kHz More than 98 dB More than 95 dB Less than 0.008 % Below measurable level Temperature: 5 C to 35 C (41 F to 95 F) Operation status: Horizontal Outputs Video output S-video output Component video output Audio output (digital output Optical) Audio output (digital output Coaxial) Audio output (analog output) 1.0 V (p-p), 75 ohm, negative sync., pin jack x 1 (Y) 1.0V (p-p), 75 ohm, negative sync. (C) 0.286 V (p-p), 75 ohm Mini DIN 4-pin x 1 , (Y) 1.0 V (p-p), 75 ohm, negative sync., pin jack x 1 (PB)/(PR) 0.7 V (p-p), 75 ohm pin jack x 2 Optical connecter x 1 0.5 V (p-p), 75 ohm , pin jack x 1 2.0 V (rms), 320 ohm, pin jack (L, R) x 2 Specifications and features are subject to change without notice. www.denom.com DPC-5.3 SERVICE PROCEDURE PRECAUTIONS 1. Ground for the work-desk. Place a conductive sheet such as a sheet of copper (with impedance lower than 10M ohm) on the work-desk and place the set on the conductive sheet so that the chassis. 2. Grounding for the test equipments and tools. Test equipments and toolings should be grounded in order that their ground level is the same the ground of the power source. 3. Grounding for the human body. Be sure to put on a wrist-strap for grounding whose other end is grounded. Be particularly careful when the workers wear synthetic fiber clothes, or air is dry. 4. Select a soldering iron that permits no leakage and have the tip of the iron well-grounded. 5. Do not check the laser diode terminals with the probe of a circuit tester or oscilloscope. 1. Replacing the fuses This symbol located near the fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjust to the symbol. Ce symbole indique que le fusible utilise est e lent. Pour une protection permanente, n'utiliser que des fusibles de meme type. Ce demier est indique la qu le present symbol est apposre. REF.NO. F1 PART NO. SR-5, T 2A DESCRIPTION 250VCA T 2.0A