Sony xm1002hx free download

File name xm-1002hx.pdf

XM-1002HX SERVICE MANUAL CORRECTION - 1 Correct your Service Manual as shown below. r US Model Canadian Model AEP Model UK Model E Model !: Indicates corrected portion Page D907 INCORRECT D908 D909 D907 CORRECT ^ D908 ^ D909 JW69 JW69 JW68 JW70 JW68 JW70 10 JW71 JW72 JW77 JW71 JW72 JW77 JW76 JW74 JW75 JW67 JW65 JW66 JW64 JW65 JW66 JW67 JW64 JW73 JW73 # 14 # JW74 JW75 JW76 (SPM-99018) Sony Corporation 9-925-785-91 Mobile Electronics Company 99G0277-1 Printed in Japan © 1999.7 Published by Quality Assurance Dept. XM-1002HX SERVICE MANUAL Ver 1.1 2001. 08 US Model Canadian Model AEP Model UK Model E Model SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 100/50 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHZ with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Speaker impedance 1* ­ 8 (stereo) 2* ­ 8 (when used as a bridging amplifier) Maximum outputs (HI-CURRENT/HI-VOLTAGE) 120/230 W x 2 (at 4 ) 380/580 W (monaural) at 4 Rated outputs (HI-CURRENT/HI-VOLTAGE) (supply voltage at 14.4 V) 50/100 W x 2 (20 Hz ­ 20 kHz, 0.04% THD, at 4 ) 70/140 W x 2 (20 Hz ­ 20 kHz, 0.1% THD, at 2 ) 140/280 W (monaural) (20 Hz ­ 20 kHz, 0.1% THD, at 4 ) Frequency response 5 Hz ­ 50 kHz ( +0.5 dB) ­3 Harmonic distortion 0.005% or less (at lkHz, 4 ) Input level adjustment range 0.2 ­ 4.0 V (RCA pin jacks) 0.4 ­ 8.0 V (High level input) High-pass filter 50 ­ 200 Hz, ­12 dB/oct Low-pass filter 50 ­ 200 Hz, ­12 dB/oct Low boost 0 ­ 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 ­ 16 V Current drain at rated output : 26 A (4 HI-VOL TAGE mode) Remote input : 2 mA Dimensions Approx. 258 x 50 x 320 mm (10 l/4 x 2 x 12 5/8 in.) (1/h/p) not incl. projecting parts and controls Mass Approx. 3.3 kg (7 lb, 4 oz.) not incl. accessories Supplied accessories Mounting screws (4), Terminal cap (1) Design and specifications are subject to change without notice. * HI-CURRENT only STEREO POWER AMPLIFIER 9-925-785-12 2001H0400-1 © 2001. 8 Sony Corporation e Vehicle Company Shinagawa Tec Service Manual Production Group 1 TABLE OF CONTENTS Specifications ... 1 1. SERVICING NOTE ... 2 2. GENERAL ... 3 3. DISASSEMBLY 3-1. Bottom Plate, Panel (Front), Panel (Rear) Removal ... 5 3-2. Amplifier Board Removal ... 5 4. ELECTRICAL ADJUSTMENT ... 6 5. DIAGRAMS 5-1. Block Diagram ...