Aiwa HS-TA380 free download

File name walkman__.pdf

HS-TA380 YH SERVICE MANUAL STEREO RADIO CASSETTE PLAYER BASIC TAPE MECHANISM : 3ZM-1 P4N SPECIFICATIONS Frequency range: Maximum output: Power source: FM: 87.5 ­ 108 MHz AM: 530 ­ 1605kHz 20 mW + 20 mW (EIAJ/16) Battery DC 3V, R6 (size AA) X2 Domestic AC power using the optional AC adaptor: AIWA AC ­ 620 / AC ­ 302 Manganese batteries (R6P,AA) Approx. 6 hours (EIAJ,1mW output, playback mode) Alkaline batteries (LR6, AA) Approx. 18 hours using (EIAJ,1mW output, playback mode) 119 (W) x 90 (H) x 38.2 (D) mm (43/4 x 35/8 x 19/16in.) Approx.171.5g (6oz) (excluding batteries) Battery life: Maximum dimensions: Weight · Design and specifications are subject to change without notice. S/M Code No. 09-986-280-0FP DISASSEMBLY INSTRUCTIONS · REMOVAL OF REAR CABINET 1. Remove 2 screws. 2. Romove 2 switch knobs. 3. Press on Rear Cabinet indicated by arrows 1 and 2 to release the catches. 4. Remove the Rear Cabinet in the direction or arrow 3 . 3 2 1 · REMOVAL OF CASSETTE LID 1. Ensure that wires linked to the FRONT C.B are stress-free. 2. Apply little force in direction 1 to the cassette lid and pull out the left cassette foot and T-spring in direction 2 . 3. Slide the cassette lid in direction of arrow 3 to remove the right cassette foot. The lid can then be removed. Right cassette foot 1 3 2 Left cassette foot T-Spring · REMOVAL OF LID, WINDOW 1. Ensure wires are stress-free. 2. Remove 3 screws. 3. Push in the direction of the black arrows to release the hooks. 4. Slide the Lid, window in the direction of the white dotted arrow to remove. Cassette lid 2 · REASSEMBLY OF THE CASSETTE LID SPRING (T-SPRING) 1. Insert A into the hole on the cassette foot. 2. Fix B onto the Frame center indicated by arrow. Cassette lid B Frame center A 3. Fix C as shown in the diagram. 4. Lastly, fix in the boss D onto the Frame center. C D Ensure this end is inserted inside the slot of the frame center. Wires pop up ·· CAUTION POINTS DURING REASSEMBLY CASSETTE LID 1. Reassemble the cassette lid confirming that the flat wires to the FRONT C.B. do not obstruct cassette insertion. Wires lay flat Slots MAIN C.B. 1. Ensure the MAIN C.B sits into the 2 slots and held by the hook. 2. Be sure that the AM BAR ANT wires do not obstruct the 2 switches. These wires should not be seen after the reassembly of the Rear Cabinet. Hook Switch AM BAR ANT wires 3 FRONT C.B. 1. To reassemble the Lid, window, slide all knobs on the Lid, window and all switches on the FRONT C.B to the MAX position. A A 3 switches at max position Hocks Front C.B. Hocks Lid windon Hocks Cassette lid 2. Slide the Lid, window in the direction of the arrows A into the Lid cassette, followed by the rest of the hooks. Ensure all catches are hooked and movement of switches are smooth. All knobs at max position 4 ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI NO. DESCRIPTION REF. NO. PART NO. KANRI NO. DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION CHIP RESISTOR PART CODE NO. REF. NO. PART