Nissan Micra [ver. K12] free download

File name IP-001.pdf

INSTRUMENT PANEL ASSEMBLY INSTRUMENT PANEL ASSEMBLY Component Parts Location To ESM MIIB9102E IP-1 INSTRUMENT PANEL ASSEMBLY 1. 4. 7. Passenger air bag module Combination meter Switch panel finisher 2. 5. 8. 11. Instrument mask Cluster lid "A" Instrument panel under tray Fuse block lid 3. 6. 9. 12. 15. 18. 21. 24. 27. 30. Upper instrument panel Instrument side mask (RH) Side ventilator grille (RH) Cluster lid C Instrument side mask (LH) Glove box lid Steering column cover Console box Steering column protector Console mask 10. Instrument finisher 13. Audio 16. Side ventilator grille (LH) 19. Tray 22. Steering lock escutcheon 25. Coin holder 28. Central ventilator grille (LH) 14. Glove box striker 17. Glove box cover assembly 20. Air conditioner finisher 23. Instrument panel stay cover 26. Instrument panel & pad 29. Central ventilator grille (RH) Removal and Installation WORK ITEM TABLE Component Parts Location Reference page (* : in this SMA file) IP-2 * IP-3 * IP-3 * IP-3 * IP-3 * IP-3 * IP-3 * IP-4 * IP-4 * IP-4 * IP-4 * IP-4 * IP-5 * IP-5 * IP-5 * IP-5 * IP-5 * IP-5 * IP-5 * IP-6 * IP-6 * To ESM Instrument panel &Brake pad [1] [2] [3] [4] [5] [6] [7] [8] [9] [ 10 ] [ 11 ] [ 12 ] [ 13 ] [ 14 ] [ 15 ] [ 16 ] [ 17 ] [ 18 ] [ 19 ] [ 20 ] [ 16 ] [ 11 ] [ 12 ] [ 13 ] [ 14 ] [ 15 ] [4] [5] [6] [7] [8] [9] [ 10 ] [4] [5] [3] [4] [3] Instrument pad [1] [2] [3] Upper instrument panel [1] [2] Combination meter [1] [2] Audio, CarWings unit [1] [2] A. Front pillar garnish B. Upper instrument panel C. Steering lock escutcheon D. Instrument panel under tray E. Switch panel finisher F. Steering column cover G. Combination switch H. Cluster lid "A" I. Combination meter J. Instrument finisher K. Cluster lid C and audio unit assembly L. Air conditioner finisher M. Instrument panel stay cover N. Glove box lid O. Glove box cover assembly P. Side ventilator grille Q. Instrument side mask R. Passenger seat air bag module S. Steering wheel T. Instrument panel & pad U. Instrument pad [ ]: The number shows the removal order. REMOVAL A. Front Pillar Garnish Refer to EI-19 "BODY SIDE TRIM" on ESM. B. Upper Instrument Panel 1. Insert a screwdriver wrapped with cloth into the instrument mask back notch to remove the instrument mask. When vehicle has sunload sensor, disconnect the sensor harness. Refer to ATC-67 "SUNLOAD SENSOR" on ESM. IP-2 INSTRUMENT PANEL ASSEMBLY 2. 3. Insert a screwdriver, etc., wrapped with cloth into the upper instrument panel passenger side back edge and disengage metal clips and lift up panel. Hold the lifted up part by hand, remove metal clips engaged in instrument pad, and remove upper instrument panel. C. Steering Lock Escutcheon Pull toward vehicle and remove. CAUTION: To install, align key cylinder end bottom protrusion with escutcheon inside notch and install. D. Instrument Panel Under Tray 1. 2. Disengage upper metal clips, hold bottom lid by hand, pull panel forward, and disengage metal clips. Remove being careful of inte

File name IP_03k12e.pdf

INSTRUMENT PANEL I BODY A SECTION B INSTRUMENT PANEL C D CONTENTS PRECAUTIONS ... 2 . Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ... 2 . Precautions ... 2 . CLIP AND FASTENER ... 3 . List of Table ... 3 . INSTRUMENT PANEL ASSEMBLY ... 4 . Component Parts Location ... 4 . Removal and Installation ... 5 . WORK ITEM TABLE ... 5 . REMOVAL ... 5 . REMOVAL AND INSTALLATION OF INSTRUMENT PAD ... 9 . REMOVAL AND INSTALLATION OF CONSOLE BOX. ... 9 . CONSOLE BOX ... 10 . Disassembly and Assembly ... 11 . INSTRUMENT PANEL PAD ... 11 . GLOVE BOX COVER ASSEMBLY ... 11 . E F G H IP J K L M IP-1 PRECAUTIONS PFP:00001 PRECAUTIONS Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" EIS004OW The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual. WARNING: q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. q Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. Precautions q EIS004OX Disconnect both battery cables in advance. q Disconnect air bag system line in advance. q Never tamper with or force air bag lid open, as this may adversely affect air bag performance. q Be careful not to scratch pad and other parts. q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may get in the way with cloth. q When removing parts with a screwdriver or other tool, pro

File name IP_05k12e.pdf

INSTRUMENT PANEL I BODY SECTION INSTRUMENT PANEL IP A B C D CONTENTS PRECAUTIONS ... 2 . Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ... 2 . Precautions ... 2 . CLIP AND FASTENER ... 3 . List of Table ... 3 . INSTRUMENT PANEL ASSEMBLY ... 4 . Component Parts Location ... 4 . Removal and Installation ... 5 . WORK ITEM TABLE ... 5 . REMOVAL ... 5 . REMOVAL AND INSTALLATION OF INSTRUMENT PAD ... 9 . REMOVAL AND INSTALLATION OF CONSOLE BOX. ... 9 . CONSOLE BOX ... 10 . Disassembly and Assembly ... 11 . INSTRUMENT PANEL PAD ... 11 . GLOVE BOX COVER ASSEMBLY ... 11 . E F G H IP J K L M IP-1 PRECAUTIONS PFP:00001 PRECAUTIONS Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" EIS004OW The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual. WARNING: q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. q Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. Precautions q EIS004OX Disconnect both battery cables in advance. q Disconnect air bag system line in advance. q Never tamper with or force air bag lid open, as this may adversely affect air bag performance. q Be careful not to scratch pad and other parts. q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may get in the way with cloth. q When removing parts with a screwdriver or other tool