Nissan Micra [ver. K12] free download

File name LT-001.pdf

INTERIOR ROOM LAMP INTERIOR ROOM LAMP Wiring Diagram -- INT/L -- To ESM MKWA1450E LT-1 INTERIOR ROOM LAMP MKWA0832E LT-2 INTERIOR ROOM LAMP MKWA3085E LT-3 INTERIOR ROOM LAMP Room Lamp Does Not Operate 1. CHECK SWITCH SIGNAL Select BCM on CONSULT-II.Check following item in "DATA MONITOR" mode with CONSULT-II. Monitor item IGN ON SW Condition Ignition switch is in ON position Ignition switch is in other position PUSH SW Ignition knob is pushed Ignition knob is released KEY IN SW Key is inserted Key is removed DOOR SW-DR Front RH door is opened Front RH door is closed DOOR SW-AS Front LH door is opened Front LH door is closed DOOR SW-RR Rear RH door is opened Rear RH door is closed DOOR SW-RL Rear LH door is opened Rear LH door is closed BACK DOOR SW Back door is opened Back door is closed CDL LOCK SW Lock/unlock switch lock position Lock/unlock switch unlock position CDL UNLOCK SW KEYLESS LOCK (*2) KEYLESS UNLOCK (*2) I-KEY LOCK (*1) Lock/unlock switch unlock position Lock/unlock switch lock position Keyless lock/unlock switch lock position Keyless lock/unlock switch unlock position Keyless lock/unlock switch unlock position Keyless lock/unlock switch lock position Intelligent Key lock/unlock switch lock position Intelligent Key lock/unlock switch unlock position I-KET UNLOCK (*1) Intelligent Key lock/unlock switch unlock position Intelligent Key lock/unlock switch lock position I-KEY ALL UNL (*1) Intelligent Key all door unlock switch unlock position Intelligent Key all door unlock switch lock position *1: Display for models with Intelligent Key system *2: Displayed for models without Intelligent Key system ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF To ESM MKIB0846E OK or NG OK >> GO TO 2. NG >> q IGN ON SW: Refer to DI-110, "Ignition ON Signal Check" on ESM. q PUSH SW (with Intelligent Key system): Refer to DI-107, "Key Switch Signal Check/With Intelligent Key System" on ESM. q KEY IN SW (without Intelligent Key system): Refer to DI-105, "Key Switch Signal Check/Without Intelligent Key System" on ESM. q OOR SW-DR: Refer to BL-58, "DRIVER SIDE" on ESM. q DOOR SW-AS: Refer to BL-60, "PASSENGER SIDE" on ESM. LT-4 INTERIOR ROOM LAMP q q q q q q q DOOR SW-RR: Refer to BL-64, "REAR RH SIDE" on ESM. DOOR SW-RL: Refer to BL-62, "REAR LH SIDE" on ESM. BACK DOOR SW: Refer to BL-66, "Check External Back Door Release Switch" on ESM. CDL LOCK/UNLOCK SW: Refer to BL-50, "Check Door Lock / Unlock Switch" on ESM. KEYLESS LOCK/UNLOCK: Refer to BL-144, "Remote controller Check" on ESM. I-KEY LOCK/UNLOCK: Refer to BL-194, "Check Door Request Switch" on ESM. I-KEY ALL UNL: Refer to BL-194, "Check Door Request Switch" on ESM. 2. CHECK BCM OUTPUT SIGNAL 1. 2. Interior room lamp switch is in DOOR position. Check voltage between BCM and ground. Terminal (+) Connector Terminal (Wire color) (-) Condition Voltage (V) Ignition switch OFF M50 73 (PU) Ground -- Key is inserted Any door switch O

File name LT-002.pdf

REAR FOG LAMP REAR FOG LAMP Wiring Diagram -- R/FOG -- To ESM MKWA1529E LT-1 REAR FOG LAMP MKWA3080E LT-2 TURN SIGNAL AND HAZARD WARNING LAMPS TURN SIGNAL AND HAZARD WARNING LAMPS Wiring Diagram -- TURN -- To ESM MKWA1444E LT-3 TURN SIGNAL AND HAZARD WARNING LAMPS MKWA3081E LT-4 PARKING, LICENSE PLATE AND TAIL LAMPS PARKING, LICENSE PLATE AND TAIL LAMPS Wiring Diagram -- TAIL/L -- To ESM MKWA1525E LT-5 PARKING, LICENSE PLATE AND TAIL LAMPS MKWA1441E LT-6 PARKING, LICENSE PLATE AND TAIL LAMPS MKWA3082E LT-7 STOP LAMP STOP LAMP Wiring Diagram-- STOP/L -- To ESM MKWA3083E LT-8 BACK-UP LAMP BACK-UP LAMP Wiring Diagram -- BACK/L -- To ESM MKWA1443E LT-9 BACK-UP LAMP MKWA3084E LT-10 ILLUMINATION ILLUMINATION System Description To ESM The illumination lamps operation is controlled by the lighting switch which built into the combination switch, BCM and IPDM E/R.Tail lamp relay is built into IPDM E/R.BCM read combination switch condition. Refer to LT189, "System Description" on ESM. Power is supplied at all times q to tail lamp relay (located in the IPDM E/R). Power is also supplied at all times q to BCM terminals 74 and 79 q through 40A fusible link (letter J, located in the fuse and fusible link box). With the ignition switch in the ON or START position, power is supplied q to BCM terminal 24 q through 10A fuse [No. 4, located in the fuse block (J/B)]. q to power window main switch terminal 5 q to front power window switch (passenger side) terminal 1 q through BCM terminal 78 Ground is supplied q to BCM terminals 2 and 70 q through grounds M19, and M20. ILLUMINATION OPERATION BY LIGHTING SWITCH When the lighting switch is turned to 1ST position, BCM read combination switch condition. Refer to LT-189, "System Description" on ESM. And BCM send illumination lamp request signal to IPDM E/R via CAN communication line. Then IPDM E/R is turned on tail lamp relay. Tail lamp relay is energized and then power is supplied: q through terminal 15 of the IPDM E/R q to heated seat switch driver side (illumination) terminal 5 q to heated seat switch passenger side (illumination) terminal 5 q through terminal 16 of the IPDM E/R q to audio unit terminal 36 q to audio and navi control unit terminal 36 q to heater control panel terminal 15 q to A/C auto amplifier terminal 11 q to headlamp aiming switch terminal 3 q to headlamp washer switch terminal 3 q to hazard switch terminal 3 q to ashtray illumination terminal 1 and q to A/T device terminal 5 q to ESP OFF switch terminal 3 Ground is supplied at all times q to heated seat switch driver side terminal 6 q to heated seat switch passenger side terminal 6 q through body grounds B17, B23, B44 and B51 q to heater control panel terminal 7 q to A/C auto amplifier terminal 12 q to headlamp aiming switch terminal 4 q to headlamp washer switch terminal 4 q to hazard switch terminal 4 q to ashtray illumination terminal 2 q to A/T device terminal 4 LT-11 ILLUMINATION to power window main switch term

File name LT_03k12e.pdf

LIGHTING SYSTEM K ELECTRICAL A SECTION B LIGHTING SYSTEM C D CONTENTS PRECAUTIONS ... 5 . Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ... 5 . HEADLAMP -CONVENTIONAL TYPE- ... 6 . Component Parts and Harness Connector Location 6 ... System Description ... 6 . OUTLINE ... 6 . COMBINATIONSWITCHREADING FUNCTION 7 ... FRIENDLY LIGHTING FUNCTION ... 7 . FAIL-SAFE FUNCTION ... 7 . CAN Communication ... 8 . SYSTEM DESCRIPTION ... 8 . CAN Communication Unit ... 8 . TYPE 1/TYPE 2 ... 9 . TYPE 3/TYPE 4 ... 12 . TYPE 5/TYPE 6 ... 14 . TYPE 7/TYPE 8 ... 17 . TYPE 9/TYPE 10 ... 19 . Wiring Diagram -- H/LAMP-- ... 22 . Terminals and Reference Value for BCM ... 24 . Terminals and Reference Values for IPDM E/R ... 25 . How to Proceed With Trouble Diagnosis ... 26 . Preliminary Check ... 26 . CHECK POWER SUPPLY AND GROUND CIRCUIT ... 26 . CONSULT-II Functions (BCM) ... 28 . CONSULT-II BASIC OPERATION ... 28 . WORK SUPPORT ... 29 . DATA MONITOR ... 29 . ACTIVE TEST ... 30 . SELF-DIAGNOSTIC RESULTS ... 30 . CONSULT-II Functions (IPDM E/R) ... 31 . CONSULT-II BASIC OPERATION ... 31 . SELF-DIAG RESULTS ... 32 . DATA MONITOR ... 32 . ACTIVE TEST ... 33 . Headlamp High Beam Does Not Illuminate (Both Sides) ... 33 . Headlamp High Beam Does Not Illuminate (One Side) ... 34 . High-Beam Indicator Does Not Illuminate ... 35 . Headlamp Low Beam Does Not Illuminate (Both Sides) ... 35 . Headlamp Low Beam Does Not Illuminate (One Side) ... 38 . Headlamp Low Beam And High Beam Does Not Illuminate (One

File name LT_05k12e.pdf

LIGHTING SYSTEM K ELECTRICAL SECTION LIGHTING SYSTEM LT A B C D CONTENTS APPLICATION NOTICE ... 5 . How to Check Vehicle Type ... 5 . PRECAUTIONS ... 6 . Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ... 6 . HEADLAMP -CONVENTIONAL TYPE- ... 7 . Component Parts and Harness Connector Location 7 ... System Description ... 7 . OUTLINE ... 7 . COMBINATIONSWITCHREADING FUNCTION 8 ... EXTERIORLAMPBATTERYSAVERCONTROL... 8 . FAIL-SAFE FUNCTION ... 8 . CAN Communication ... 9 . SYSTEM DESCRIPTION ... 9 . CAN Communication Unit ... 9 . TYPE 1/TYPE 2 ... 10 . TYPE 3/TYPE 4/TYPE 5/TYPE 6 ... 13 . TYPE 7/TYPE 8 ... 15 . TYPE 9/TYPE 10/TYPE 11/TYPE 12 ... 18 . TYPE 13/TYPE 14 ... 20 . Wiring Diagram -- H/LAMP-- ... 22 . Terminals and Reference Value for BCM ... 24 . Terminals and Reference Values for IPDM E/R ... 25 . How to Proceed With Trouble Diagnosis ... 26 . Preliminary Check ... 26 . CHECK POWER SUPPLY AND GROUND CIRCUIT ... 26 . CONSULT-II Functions (BCM) ... 28 . CONSULT-II BASIC OPERATION ... 28 . WORK SUPPORT ... 29 . DATA MONITOR ... 29 . ACTIVE TEST ... 30 . SELF-DIAGNOSTIC RESULTS ... 30 . CONSULT-II Functions (IPDM E/R) ... 31 . CONSULT-II BASIC OPERATION ... 31 . SELF-DIAG RESULTS ... 32 . DATA MONITOR ... 32 . ACTIVE TEST ... 33 . Headlamp High Beam Does Not Illuminate (Both Sides) ... 33 . Headlamp High Beam Does Not Illuminate (One Side) ... 34 . High-Beam Indicator Does Not Illuminate ... 35 . Headlamp Low Beam Does Not Illuminate (Both Sides) ... 35 . Headlamp Low Beam Does Not Illuminate (One Side) ...