File information: | |
File name: | 42DPC85_schemdiag.part1.rar [preview 42DPC85] |
Size: | 1423 kB |
Extension: | rar |
Mfg: | Toshiba |
Model: | 42DPC85 🔎 |
Original: | |
Descr: | 3 files, 86 pages, service manual for Toshiba plasma monitor model # 42DPC85. |
Group: | Electronics > Consumer electronics > TV |
Uploaded: | 03-10-2007 |
User: | Mdy4Blues |
Multipart: | 0 1 2 3 4 5 6 |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 1 | |
File name 42DPC85_schemdiag.pdf SCHEMATIC DIAGRAM MODEL : 42DPC85 WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "SERVICE SAFETY PRECAUTIONS" ON THE MANUAL FOR THIS MODEL. CAUTION : The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals. Before replacing any of these components, read carefully the SERVICE SAFETY PRECAUTIONS on the MANUAL for this model. Do not degrade the safety of the receiver through improper servicing. NOTE: 1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5% tolerance carbon resistor, unless otherwise noted as the following marks. 1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt 1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt K = ±10% G = ±2% F = ±1% 2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in ?F, and the values more than 1 in pF. All capacitors are ceramic 50V, unless otherwise noted as the following marks. Electolytic capacitor Mylar capacitor 3. The parts indicated with " * " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all controls at normal, line voltage 220 volts. 5. Waveforms are taken receiving color bar signal with enough sensitivity. 6. Voltage reading shown are nominal values and may vary ±20% except H.V. SCHEMATIC DIAGRAM STRUCTURE: CONNECTOR [SHEET-1/4] ... 1/47 AV-TERMINAL [SHEET-2/4] ... 2/47 A-OUT [SHEET-3/4] ... 3/47 EXPANDER FOR PDP [SHEET-4/4] ... 4/47 FRONT-AV ... 5/47 IR LED ... 6/47 KEY ... 7/47 LOWB ... 8/47 SIGNAL ANALOG IN [SHEET-200] ... 9/47 D IN A [SHEET-300] ... 10/47 D IN B [SHEET-301] ... 11/47 HDMI (Link, I2C) [SHEET-302] ... 12/47 HDMI Rx#2 (Video/Audio) [SHEET-303] ... 13/47 HDMI Rx#3 (PWR,Audio) [SHEET-304] ... 14/47 HDMI AUDIO PLL [SHEET-305] ... 15/47 HDMI AUDIO DAC [SHEET-306] ... 16/47 HDMI AUDIO OUT [SHEET-307] ... 17/47 HDMI CONTROLLER [SHEET-308] ... 18/47 EEPROM1 [SHEET-309] .. |
Date | User | Rating | Comment |