Ricoh 1515 free download

File name p2p_sc2.pdf

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A By-pass Feed Clutch Upper Ppaer Feed Clutch CN4-1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 SOL 1 Front/Right Door Safety Switch CN294-1 -2 By-pass Paper End Sensore Duplex Inverter Sensor Image Density (ID) Sensor Toner Density (TD) Sensor Exposure Lamp Scanner H.P. Sensor Toner Supply Clutch Scanner Motor Quenching (LED) Lamp Registration Sensor Total Counter Exhaust Fan Motor Duplex Motor Platen Cover Sensor Polygonal Mirror Motor Paper End Sensor Main Motor Paper Exit Sensor MC2 CN292-1 -2 MC3 +24V [24] CN293-1 -2 MC4 +24V [24] CN291-1 -2 CN3-1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 Registration Clutch Operation Panel Board (MFP) (PCB4) Fusing Solenoid A COM LES8 LES9 LES10 Q_LES Q_LEC0 Q-LEC1 Q-LEC2 Q-LEC3 COM COM SWD2 SWD3 SWD4 SWD5 SWD6 SWD7 SWC0 SWC1 SWC2 SWC3 SWC4 +24V [24] SW1, 2 L1 B +24V [24] Option Key Counter New PCU Detection ["24] ["24] ["24] ["24] B For Basic Machine only Operation Panel Board (Basic) (PCB3) S1 S2 x1 S3 MC1 S7 M1 M2 M3 S5 L2 S4 N S6 CO1 M4 Lamp Stabilizer Board (PCB2) S8 S9 M5 Power Pack-BCT (PCB11) CN290-15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 CO2 For Field Engineer IC Card CN101 CN1--6 -5 -4 -3 -2 -1 x2 CN127-1 -2 -3 CN129-1 -2 CN136-1 -2 -2 CN137-1 -2 -3 CN122-1 -2 -3 CN138-1 -2 -3 -4 CN128-1 -2 -3 CN123-3 -4 -5 -6 -7 -8 CN132-1 -2 -3 -4 -2 CN114-2 -1 CN116-1 -2 -3 -4 -5 CN117-1 -2 -3 -4 -5 CN126-1 -2 -3 -4 -5 -6 CN108-1 -2 -3 -4 -5 -6 CN140-1 -2 -3 CN130-1 CN123-1 CN119-1 CN115-1 -2 -3 -4 -5 -6 -7 -8 -9 CN105-1 -2 -3 -4 -5 -6 CN124-1 -2 CN125-1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -2 -4 NV RAM IC Socket 23 ON ["24] GND [0] ["5] PCU_SET GND [0] Feed Back IDS PWMIDS [!5] GND [0] +5V [5] Set [!5] GND [0] Feed Back TDS +5V [5] +24V [24] GND [0] ON ["5] Ready ["5] Clock GND [0] GND [0] Lamp ON ["24] +24V [24] +24V [24] +24V [24] +24V [24] A [0-24] AB [0-24] B [0-24] BB [0-24] +24V [24] FAN1_LK ["24] ["24] +24 [24] GND [0] ["5] +5V [5] GND [0] GND [0] ["5] +5V [5] GND [0] ["5] +5V [5] GND [0] [!5] +5V [5] GND [0] [!5] +5V [5] C PWM_B [0 0/5] Feed Back-B Feed Back-C PWM_C[0 0/5] PWM_TP[0 0/5] PWM_TM[0 0/5] Feed Back-T +5V [5] GND [0] +24V [24] +24V [24] ["24] ["24] ["24] ["24] CLK_OPU GND [0] DI_OPU DO_OPU XPWSW +5V [5] MMCLK MM_BK [!5] /MM_DR [!5] MM_ST ["5] /MM_RDY ["5] GND [0] GND [0] +24V [24] +24V [24] +5V [5] FB_MHEAT +24V [24] GND [0] Set ["5] +24V [24] ["5] +24V [24] 0/24] 0/24] 0/24] 0/24] ["24] +24V [24] ["24] ["24] C [24 [24 [24 [24 Zero Cross ["24] Fusing Lamp ["24] Relay Trig. PSU_OFF [0] GND ["24] Relay ON [24] +24 VS BICU (PCB6) [5] +5V CSS_RXD CSS_TXD [0] GND CSS_CTS CSS_RST [0] GND [5] +5V M6_SYNC M6_ALCNT1 M6_ALCNT0 M6_SINCNT2 M6_SINCNT1 M6_BB M6_B M6_AB M6_A [24] +24V [24] +24V [0] GND [0] GND [0] GND [5] +5V \PTU_OPN PTU_LAT PTU_SID P

File name s_af2013.pdf

Model S-C2 (Machine Code: B129/B130/B168/B169) SERVICE MANUAL 9 March 2004 Subject to change !IMPORTANT SAFETY NOTICES PREVENTION OF PHYSICAL INJURY 1. Be sure that the power cord is unplugged before disassembling or assembling parts of the copier or peripherals. 2. The wall outlet should be near the copier and easily accessible. 3. Note that electrical voltage is supplied to some components of the copier and the paper tray unit even while the main power switch is off. 4. If you start a job before the copier completes the warm-up or initializing period, keep hands away from the mechanical and electrical components until job execution has started. The copier will start making copies as soon as warm-up or initialization is finished. 5. The inside and the metal parts of the fusing unit become extremely hot while the copier is operating. Be careful to avoid touching those components with your bare hands. HEALTH SAFETY CONDITIONS Toner and developer are nontoxic, but getting either of these into your eyes may cause temporary eye discomfort. Try to remove with eye drops or flush with water. If material remains in eye or if discomfort continues, get medical attention. OBSERVANCE OF ELECTRICAL SAFETY STANDARDS The copier and its peripherals must be installed and maintained by a customer service representative who has completed the training course on those relevant models. LITHIUM BATTERIES Incorrect replacement of lithium battery(s) on the FCU may pose risk of explosion. Replace only with the same type or with an equivalent type recommended by the manufacturer. Discard used batteries in accordance with the manufacturer's instructions. SAFE AND ECOLOGICAL DISPOSAL 1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly if exposed to an open flame. 2. Dispose of used toner, developer, and organic photoconductors in accordance with local regulations. (These are nontoxic supplies.) 3. Dispose of replaced parts in accordance with local regulations. 1 LASER SAFETY The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical units in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis and laser subsystems to the factory or service depot when replacement of the optical subsystem is required. !WARNING Use of controls not specified in this manual, or performance of adjustments or procedures not specified in this manual, may result in hazardous radiation exposure. !WARNING FOR LASER UNIT WARNING: Turn off the main switch before attempting any of the procedures in the Laser Unit section. Laser beams can cause serious damage to eyes. CAUTION MARKING: B130R934.WMF Symbols and Abbreviations This manual uses the symbols and abbreviations shown