Braun Shave Line free download

File name 5524.pdf

Service Documentation Braun pocket battery deluxe Market Release 2/90 5524 5524 BINC Rev: 7/96 BAG Rev: 2/90 Service Documentation Exploded Drawing 5524 5524 - 2 BINC Rev: 7/96 BAG Rev: 7/95 Service Documentation Spare Parts List 5524 Part Description Cleaning brush Protective cap Shaving head frame Shaving foil Cutter block Circlip Cutter block support, w/pos. no 8 Conical coil spring Oscillating frame Eccentric Motor Switch handle Housing, upper part Housing, lower part Spring Spring catch Battery cover Pos. No. 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 Part Number 5524804 5524802 5523624 5524764 5524761 0107001 5523812 5523042 5523510 5523807 5523626 5523034 5524611 5524629 5523018 5523016 5524096 5524 - 3 BINC Rev: 7/96 BAG Rev: 2/90 Service Documentation Service Information 5524 Description of shaver Battery shaver Housing: Shaving head frame: Shaving foil: Cutter block: Protective cap: for pocket battery: for pocket deluxe: Plastic Plastic 40 mm wide, removable (snap connection) 30 cutter blades, 3° obliquely positioned, 10 mm diameter, plastic removal with clamp for cleaning brush swivel protective cap integrated in the unit with locking. General Information Drive: Power supply: 2.7 V direct-current motor. Power transmission to cutter block by means of eccentric and plastic oscillating frame. Supply by means two 1.5 V Mignon cells (type LR6/AM3/ MN 1500/AA alkaline). Technical data 1 Amplitude at the cutter block: approx. 2.4 min. 2. Rotational speed: approx. 6200 r.p.m. 3. Operating current: approx. 500 mA 4. Operating capacity: approx. 60 shaving minutes 5524 - 4 BINC Rev: 7/96 BAG Rev: 2/90 Service Documentation Service Information 5524 Disassembly · · · · · · Remove batteries, take off cutting parts. Disassemble cutter block support with rubber seal. The housing halves are held together by snap-action. Apply pressure diagonally on sides of housing and squeeze, until parts disengage. Start at battery well to separate housing parts. Attention! Spring (16) and catch (17) will jump out of housing parts, also the battery cover (18) will drop out. Motor (12) with oscillating frame (10) can now be removed from housing, lower part (15). Assembly The assembly will be accomplished in a reversed sequence. Attention should be paid to the following points: · · · · · The motor (12) must be installed with correct polarity. The minus-pole of the motor (the motor contact which is not soldered), must be pinched between the battery contact. Insert oscillating frame (10) in such away, to line-up with the upper edge of the housing. First engage housing halves on the upper side, put battery cover (18) into place at the bottom, then press both parts together. Assemble cutter block support (7) and pull rubber seal (8) over bead on housing. After housing has been assembled, slide spring catch (17) with spring (16) into the pockets Insert batteries, carry out functional tests. 5524 - 5

File name 5584_28.pdf

Service Documentation Braun flex control 4510 universal Market Release 4/93 5584/28 5584/28 BINC Rev: 7/96 BAG Rev: 4/93 Service Documentation Exploded Drawing 5584/28 5584/28 - 2 BINC Rev: 7/96 BAG Rev: 12/95 Service Documentation Spare Parts List 5584/28 Part Description Protective cap 4000 series shaving foil 4000 series cutter block Sealing plate Bearing screw Swivel frame Screw Head carrier Spring Lever Lever bearing Pin Spring Chassis, cpl. Sliding plate PCB Locking button Housing bottom Housing cover Square nut Screw Plug pin Leg spring for sliding plate Spring lever Pos. No. 1 2 3 4 5 6 7 9 10 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part Number 5585060 order by description order by description 5528007 5528004 5528626 5586050 5528625 5586225 5586215 5586623 5586042 5586043 5528629 5585621 5585623 5585072 5528883 5584640 5421026 5586038 5585070 5586213 5586224 5584/28 - 3 BINC Rev: 7/96 BAG Rev: 5/94 Service Documentation Service Information 5584/28 Description of shaver Rechargeable and cord shaver: Housing: Shaving head and swivel frame: Double shaving foil: Double Cutter block: Long hair cutter: Slide switch: 12-240 V charging voltage without switchover Thermoplast, black Plastic Frame construction, "Sixtant"-geometry, Nickel, Platinum-coated Plastic, 27 cutter blades, 6 mm diameter Integral part of slide (switch). Shaving head and long hair cutter are working in opposite direction to each other. 3 switch functions 1. on/off 2. for a close shave with locked swivel head 3. long hair-cutting General Information Drive: Power supply: 2.4 V direct current motor. Power transmission to shaving system by eccentric drive. Supply by means of two built-in rechargeable batteries or by direct mains supply. A built-in electronic charger controls the supply automatically, independently of the mains voltage or frequency. A green control lamp serves as a visible sign of charging operation start by impulse-charging at 12 V. at 12V from 100V on from total discharged condition approx. 20 hours approx. 1 hour approx. 4 hours Charging time: After maximum charging capacity has been reached, the electronic device switches back to a compensating trickle charge, which maintains capacity. A special charging cable with fuse is available, for use with outlets in car or boats. The most favorable ambient temperatures for shaver functioning is between + 15 °C and + 35 °C. By no means the temperature should be below 0 °C or above + 40 °C when charging the shaver. Technical data 1. Amplitude measured at the cutter block: 2. Revolution when run on rechargeable battery: 3. Current input when run on line-voltage (220V): 4. Operating capacity after shaver has been fully charged: 2.6 - 3 mm minimum 6300 RPM without long hair-cutter 17 mA without long hair-cutter approx. 70 shaving minutes 5584/28 - 4 BINC Rev: 7/96 BAG Rev: 4/93 Service Documentation Service Information 5584/28 Disassembly: · · · · · · · Disengage shaving foil (2) with protective cap

File name 5585.pdf

Service Documentation Braun flex control 4520 Market Release 1/90 5585 5585 BINC Rev: 7/96 BAG Rev: 7/91 Service Documentation Exploded Drawing 5585 5585 - 2 BINC Rev: 7/96 BAG Rev: 1/94 Service Documentation Spare Parts List 5585 Part Description Protective cap 4000 series shaving foil (black) 4000 series cutter block Foam rubber seal Bearing screw Swivel frame, black Screw Adapter Head carrier, black Bearing into head carrier Spring Lever Lever bearing Pin Spring Chassis, cpl. Sliding plate, black PCB (Ni-Hy) Locking button, black Housing bottom, black Housing cover, black Square nut Screw Plug pin, black Leg spring for sliding plate Spring lever Cleaning brush Coiled cord Case Pos. No. 1 2 3 4 5 6 7 8 9 9a 10 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part Number 5585060 order by description order by description 5586148 5586054 5585625 5586050 5586035 5585626 5586107 5586225 5586215 5586623 5586042 5586043 5586629 5585621 5585623 5585072 5585642 5585640 5421026 5586038 5585070 5586213 5586224 5002820 5001750 5586875 5585 - 3 BINC Rev: 7/96 BAG Rev: 5/94 Service Documentation Service Information 5585 Description of shaver Rechargeable and cord shaver: Housing: Shaving head and swivel frame: Double shaving foil: Double Cutter block: Long hair cutter: Slide switch: 12-240 V charging voltage without switchover Thermoplast, black or metallic gray Metal Frame construction, "Sixtant"-geometry, Nickel, Platinum-coated Plastic, 27 cutter blades, 6 mm diameter Integral part of slide (switch). Shaving head and long hair cutter are working in opposite direction to each other. 3 switch functions 1. on/off 2. for a close shave with locked swivel head 3. long hair-cutting With mains cord-adapter (special accessory) Shaver bracket: General Information Drive: Power supply: 2.4 V direct current motor. Power transmission to shaving system by eccentric drive. Supply by means of two built-in rechargeable batteries or by direct mains supply. A built-in electronic charger controls the supply automatically, independently of the mains voltage or frequency. A green control lamp serves as a visible sign of charging operation start by impulse-charging at 12 V. at 12V from 100V on from total discharged condition approx. 20 hours approx. 1 hour approx. 4 hours Charging time: After maximum charging capacity has been reached, the electronic device switches back to a compensating trickle charge, which maintains capacity. A special charging cable with fuse is available, for use with outlets in car or boats. The most favorable ambient temperatures for shaver functioning is between + 15 °C and + 35 °C. By no means the temperature should be below 0 °C or above + 40 °C when charging the shaver. When 80% of the capacity of the rechargeable battery has been used, a red capacity signal lamp continues to light for 5 sec. after turning off the shaver and operates continuously during the entire shaving cycle. Technical data 1. Amplitude measured at the cutter block:

File name 5585_09.pdf

Service Documentation Braun flex control 4520 universal Market Release 5/93 5585/09 5585/09 BINC Rev: 7/96 BAG Rev: 5/93 Service Documentation Exploded Drawing 5585/09 5585/09 - 2 BINC Rev: 7/96 BAG Rev: 1/95 Service Documentation Spare Parts List 5585/09 Part Description Protective cap 4000 series shaving foil 4000 series cutter block Sealing plate Bearing screw Swivel frame Screw Head carrier Spring Lever Lever bearing Pin Spring Chassis, cpl. Sliding plate PCB Locking button Housing bottom Housing cover Square nut Screw Plug pin Leg spring for sliding plate Spring lever Pos. No. 1 2 3 4 5 6 7 9 10 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part Number 5585060 order by description order by description 5528007 5528004 5528626 5586050 5528625 5586225 5586215 5586623 5586042 5586043 5528629 5585621 5585623 5585072 5509882 5585984 5421026 5586038 5585070 5586213 5586224 5585/09 - 3 BINC Rev: 7/96 BAG Rev: 5/94 Service Documentation Service Information 5585/09 Description of shaver Rechargeable and cord shaver: Housing: Shaving head and swivel frame: Double shaving foil: Double Cutter block: Long hair cutter: Slide switch: 12-240 V charging voltage without switchover Thermoplast, black Plastic Frame construction, "Sixtant"-geometry, Nickel, Platinum-coated Plastic, 27 cutter blades, 6 mm diameter Integral part of slide (switch). Shaving head and long hair cutter are working in opposite direction to each other. 3 switch functions 1. on/off 2. for a close shave with locked swivel head 3. long hair-cutting General Information Drive: Power supply: 2.4 V direct current motor. Power transmission to shaving system by eccentric drive. Supply by means of two built-in rechargeable batteries or by direct mains supply. A built-in electronic charger controls the supply automatically, independently of the mains voltage or frequency. A green control lamp serves as a visible sign of charging operation start by impulse-charging at 12 V. at 12V from 100V on from total discharged condition approx. 20 hours approx. 1 hour approx. 4 hours Charging time: After maximum charging capacity has been reached, the electronic device switches back to a compensating trickle charge, which maintains capacity. A special charging cable with fuse is available, for use with outlets in car or boats. The most favorable ambient temperatures for shaver functioning is between + 15 °C and + 35 °C. By no means the temperature should be below 0 °C or above + 40 °C when charging the shaver. When 80% of the capacity of the rechargeable battery has been used, a red capacity signal lamp continues to light for 5 sec. after turning off the shaver and operates continuously during the entire shaving cycle. Technical data 1. Amplitude measured at the cutter block: 2. Revolution when run on rechargeable battery: 3. Current input when run on line-voltage (220V): 4. Operating capacity after shaver has been fully charged: 2.6 - 3 mm minimum 6300 RPM without long hair-cutter 17 mA without

File name 5586.pdf

Service Documentation Braun flex control 4525 Market Release 1/90 5586 5586 BINC Rev: 7/96 BAG Rev: 7/91 Service Documentation Exploded Drawing 5586 5586 - 2 BINC Rev: 7/96 BAG Rev: 1/95 Service Documentation Spare Parts List 5586 Part Description Protective cap 4000 series shaving foil, gray 4000 series cutter block Foam rubber seal Bearing screw Swivel frame, silver Screw Adapter Head carrier, silver Bearing into head carrier Spring Lever Lever bearing Pin Spring Chassis, cpl. Sliding plate, gray PCB (Ni-Hy) Locking button, gray Housing bottom Housing cover, silver Square nut Screw Plug pin, gray Leg spring for sliding plate Spring lever Cleaning brush Coiled cord Case Pos. No. 1 2 3 4 5 6 7 8 9 9a 10 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part Number 5586048 order by description order by description 5586148 5586054 5586625 5586050 5586035 5586626 5586107 5586225 5586215 5586623 5586042 5586043 5586629 5586621 5586647 5586072 5586881 5586640 5421026 5586038 5586074 5586213 5586224 5002820 5001967 5586875 5586 - 3 BINC Rev: 7/96 BAG Rev: 5/94 Service Documentation Service Information 5586 Description of shaver Rechargeable and cord shaver: Housing: Shaving head and swivel frame: Double shaving foil: Double Cutter block: Long hair cutter: Slide switch: 12-240 V charging voltage without switchover Thermoplast, black or metallic gray Metal Frame construction, "Sixtant"-geometry, Nickel, Platinum-coated Plastic, 27 cutter blades, 6 mm diameter Integral part of slide (switch). Shaving head and long hair cutter are working in opposite direction to each other. 3 switch functions 1. on/off 2. for a close shave with locked swivel head 3. long hair-cutting With mains cord-adapter (special accessory) Shaver bracket: General Information Drive: Power supply: 2.4 V direct current motor. Power transmission to shaving system by eccentric drive. Supply by means of two built-in rechargeable batteries or by direct mains supply. A built-in electronic charger controls the supply automatically, independently of the mains voltage or frequency. A green control lamp serves as a visible sign of charging operation start by impulse-charging at 12 V. at 12V from 100V on from total discharged condition approx. 20 hours approx. 1 hour approx. 4 hours Charging time: After maximum charging capacity has been reached, the electronic device switches back to a compensating trickle charge, which maintains capacity. A special charging cable with fuse is available, for use with outlets in car or boats. The most favorable ambient temperatures for shaver functioning is between + 15 °C and + 35 °C. By no means the temperature should be below 0 °C or above + 40 °C when charging the shaver. When 80% of the capacity of the rechargeable battery has been used, a red capacity signal lamp continues to light for 5 sec. after turning off the shaver and operates continuously during the entire shaving cycle. Technical data 1. Amplitude measured at the cutter block: 2. Revolu

File name 5596.pdf

Service Documentation Braun 255 Market Release 4/94 5596 5596 BINC Rev: 7/96 BAG Rev: 4/94 Service Documentation Exploded Drawing 5596 5596 - 2 BINC Rev: 9/96 BAG Rev: 3/96 Service Documentation Spare Parts List 5596 Part Description Protective cap 100/200 series shaving foil frame 100/200 cutter block Circlip Cutter block support w/seal Coil spring Oscillating frame Motor Retaining spring PCB Insert Plug plate Housing upper part, cpl. Housing lower part Luminous rod Housing support Housing screw Shave and shape attachment Cleaning brush Coiled cord Case Pos. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part Number 5461038 order by description order by description 0107001 5523812 5461040 5461009 5596651 5596006 5596630 5461003 5596648 5596636 5596627 5596004 5596635 0038210 5596650 5002820 5323015 5461088 5596 - 3 BINC Rev: 7/96 BAG Rev: 11/95 Service Documentation Service Information 5596 Description of shaver Rechargeable and cord shaver: Housing: Shaving head frame: Cutter block: Long hair trimmer Drive: Power transmission: Power supply: Charging of the shaver: Charging time: from 100 V onwards Technical data Amplitude at the cutter block: Rotational speed on accumulator drive: Current consumption on mains: operation 220 V Operating capacity after the shaver: is fully charged: 2.8 mm. approx. 6300 rpm, long-hair trimmer disengaged. max. 17 mA, long-hair trimmer disengaged. approx. 35 shaving minutes. 12 - 240 V, 50 - 60 Hz, 5 W. Plastic. Plastic with integrated shaving foil. Plastic, 30 cutter blades, 3° obliquely positioned, 10 mm diameter. Switchable through a separate switch. 1.2 V direct-current motor. to cutter block by means of eccentric and plastic oscillating frame. Supply by means of one built-in rechargeable NH-battery. is indicated by a green lamp. on 12 V approx. 20 hours. approx. 1 hour. 5596 - 4 BINC: 7/96 BAG: 9/94 Service Documentation Service Information 5596 Dismantling: · · · · · · · · · Shaving foil frame (2) Cutter block (3) Cutter block support with foam rubber seal (5). Housing support (16). Housing upper part (13) plate (12) Oscillating frame (7) Insert (11) PCB (10) Plug plate (12) Motor (8) - remove - remove - remove circlip (4) - remove cutter block support with foam rubber seal (5) and conical coil spring (6). - remove screws (17) and take off housing support (16). - Insert a coin into the marked indentation of the plug and turn it counterclockwise. Separate housing parts from each other. - remove from housing upper part (13). - remove from housing lower pad (14). - lift out of housing lower part (14) - unsolder the connection wires from the motor (8). - remove from housing lower part (14) - pull apart the sides of the motor housing in the housing lower part (14) - remove spring frame (9) and motor (8). Assembly: · The assembly is made in reverse order. Attention: · · · · · After each opening of the device a new plug plate (12) has to be inserted. Insert plug plate (12) in housing lower part (14

File name 5597.pdf

Service Documentation Braun 155 Market Release 4/94 5597 5597 BINC Rev: 7/96 BAG Rev: 8/94 Service Documentation Exploded Drawing 5597 5597 - 2 BINC Rev: 8/98 BAG Rev: 9/95 Service Documentation Spare Parts List 5597 Part Description Protective cap 100/200 series shaving foil frame 100/200 series cutter block Circlip Cutter block support w/seal Coil spring Oscillating frame Motor Retaining spring PCB Insert Plug plate Housing upper part, cpl. Spring catch for pos. 13 Spring for pos. 13 Housing lower part Luminous rod Housing support Housing screw Cleaning brush Coiled cord Case Pos. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part Number 5461038 order by description order by description 0107001 5523812 5461040 5462009 5596858 5596006 5596630 5461003 5597629 5597657 5461006 5461007 5597627 5596004 5597632 0038210 5002820 5001967 5585097 5597 - 3 BINC Rev: 7/96 BAG Rev: 11/95 Service Documentation Service Information 5597 Description of shaver Rechargeable and cord shaver: Housing: Shaving head frame: Cutter block: Long hair trimmer Drive: Power transmission: Power supply: Charging of the shaver: Charging time: from 100 V onwards Technical data Amplitude at the cutter block: Rotational speed on accumulator drive: Current consumption on mains: operation 220 V Operating capacity after the shaver: is fully charged: 2.8 mm. approx. 6300 rpm, long-hair trimmer disengaged. max. 17 mA, long-hair trimmer disengaged. approx. 35 shaving minutes. 100 - 240 V, 50 - 60 Hz, 2 W. Plastic. Plastic with integrated shaving foil. Plastic, 30 cutter blades, 3° obliquely positioned, 10 mm diameter. Switchable through a separate switch. 1.2 V direct-current motor. to cutter block by means of eccentric and plastic oscillating frame. Supply by means of one built-in rechargeable NH-battery. is indicated by a green lamp. on 12 V approx. 20 hours. approx. 1 hour. 5597 - 4 BINC Rev: 7/96 BAG Rev: 9/94 Service Documentation Service Information 5597 Dismantling: · · · · · · · · · Shaving foil frame (2) Cutter block (3) Cutter block support with foam rubber seal (5). Housing support (16). Housing upper part (13) Oscillating frame (7) Insert (11) PCB (10) Plug plate (12) Motor (8) - remove - remove - remove circlip (4) - remove cutter block support with foam rubber seal (5) and conical coil spring (6). - remove screws (17) and take off housing support (16). - Insert a coin into the marked indentation of the plug plate (12) and turn it counterclockwise. Separate housing parts from each other. - remove from housing upper part (13). - remove from housing lower pad (14). - lift out of housing lower part (14) - unsolder the connection wires from the motor (8). - remove from housing lower part (14) - pull apart the sides of the motor housing in the housing lower part (14) - remove spring frame (9) and motor (8). Assembly: · The assembly is made in reverse order. Attention: · · · · · After each opening of the device a new plug plate (12) has to be inserted. Insert p

File name 5601.pdf

Service Documentation Braun exact power Market Release 10/99 EP 100, 80, 60 5601 5601 BINC Rev: 9/99 BAG Rev: 9/99 Service Documentation Exploded Drawing 5601 5601 - 2 BINC Rev: 9/99 BAG Rev: 9/99 Service Documentation Spare Parts List 5601 Part Description Comb attachment Cutter set Small parts set Swivel frame Housing front part (silver) Motor PCB (1 hr) Housing back part Coiled cord Cleaning brush Case Pos. No. 1 2 3 4 5 6 7 8 Part Number 5601621 5601622 5601623 5601632 5601633 5601624 5601625 5601634 5002704 5503120 7000062 5601 - 3 BINC Rev: 9/99 BAG Rev: 9/99 Service Documentation Service Information 5601 Principle Nominal voltage Nominal frequency Housing Cutting system Switch function Rechargeable / cord shaver 120 VAC 50 - 60 Hz Plastic material Switchable double cutting system (21 resp. 33 mm width) Central sliding switch with integrated "speed"-shifting and button for lock function Separate memory slide for 7 beard-length positions (1 - 2 - 3 - 6 - 9 - 12 and 16 mm) 1.2 V DC motor switchable to two positions Position 1: Position 2: approx. 4.760 r.p.m. (min.) approx. 6.120 r.p.m. (max.) approx. 5.600 r.p.m. (min.) approx. 6.800 r.p.m (max.) Technical Data Drive Revolutions (after a recharging time of least 3 minutes and with greased cutting system) Power transmision Power supply Charging time Via eccenter directly onto the shaving system Via a built in, rechargeable NH-battery, resp. a built-in battery recharger EP 100 EP 80 EP 60 EP 100 EP 80 EP 60 approx. 1 hour approx. 8 hours approx. 16 hours approx. 4 watts approx. 5 watts approx. 1,35 watts Power consumption Charging of the shaver Operating capacity Is indicated by a green lamp after full recharge approx. 30 cutting minutes 5601 - 4 BINC Rev: 9/99 BAG Rev: 9/99 Service Documentation Service Information 5601 Comb attachment (1) Cutter set (2) Swivel frame (4) Set sliding switch in "0" position. Pull off comb attachment by snap action. To be snapped out by pressing buttons "A". Insert a small Torx screwdriver into the hole of the springs (3a) and snap them out by pushing towards the inside of the frame. Remove the pin (3b). Unhinge and remove swivel frame (4) (see diagram below). Dismantling Housing Unscrew screw "B" (3c) of the housing back part (8). Press together the housing front part (5) in the area of the bearing pin; then, insert a wide-bladed screwdriver into the guide slot on the left side of the sliding switch and unhinge the housing snaps. Now, pull apart the housing halves. Remove the screw (3c) in the housing font part (5). Unsolder the connecting wires to the PCB (7). Remove and snap out plug connector. Motor (6) PCB (7) 5601 - 5 BINC: 9/99 BAG: 9/99 Reassembly Service Documentation Service Information 5601 The reassembly is done in reversed order. Please pay attention to the following points: Motor (6) Insert the motor (6) into the housing front part (5) in such a way that the indentations for the swivel head snaps on the left side of th

File name 5614.pdf

Service Documentation Braun Pocket Twist 350 Market Release 4/97 5614 5614 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Exploded Drawing 5614 5614 - 2 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Spare Parts List 5614 Part Description Shaving foil frame Cutter block Cleaning brush Pos. No. 7 8 24 Part Number 5614763 5524761 5524780 This shaver is a non-serviceable item. Refer to the Inventory Recommendations for Non-serviceable Products page in the Braun price book for article numbers when replacing the unit under warranty. 5614 - 3 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Service Information 5614 Technical Data Principle Housing Shaving head: Cutter block: Drive: Power transmission: Power supply: Amplitude: Revolutions: Working current: Operating capacity: Dismantling Protective caps (1, 22): Remove cleaning brush (24). Take off screw (21). Pull apart the protective caps (1) and (22), and lever them, one after the other, from the housing shelves. To be unlocked through unlocking pins and to be removed. To be extracted. Remove circlip (9). Take off cutter block support (10) with ring seal and conical coil spring (11). Remove batteries. Unscrew the 3 housing screws (19). By means of a grip ring pliers inserted into the battery box, press apart the housing shelves (3) and 5614 - 4 Battery operated shaver with switch-on protection. Plastic material Plastic frame with integrated shaving foil. 30 blades, 3° inclined, 10 mm diameter, plastic frame. 2.7 V DC motor. via eccenter and oscillating frame onto the shaving system. by 2 Mignon batteries 1.5 V (type LR6, AM3, MN 1500/AA alkaline) Approx. 2.4 mm, measured at the cutter block. Approx. 6200 r.p.m. (with new batteries) Approx. 5500 r.p.m. (by 2.4 V minimum) Approx. 500 mA Approx. 60 shaving minutes. Shaving foil frame (7): Cutter block (8): Cutter block support (10): Open housing: BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Service Information 5614 (20), one after the other (see exploded drawing "A"). Attention: When opening the housing shelves, the spring catches (17) will snap out. Before extracting the motor, the slider (2) must be switched in the 'on' position. Snap out the motor from the direction of the eccenter and remove it together with the minus contact. Attention: When extracting the motor please take care that the spring wire (15) does not get lost. (Mostly the wire sticks to the motor through the magnetic effect.) All further dismantling steps do not require further explanation. Motor (16): Reassembly The reassembly is made in reversed order. Attention must be paid to the following: Battery contacts (13, 14): Before inserting the plus contact (14) into the housing upper part (3), please absolutely make sure that the slider (2) is adjusted in the 'on' position. When inserting the battery contacts, care must be taken that the holes of the metal straps match exactly with the corresponding pins in the housing upper part (3). Insert the s

File name 5615.pdf

Service Documentation Braun Pocket Twist Plus 375 Market Release 4/97 5615 5615 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Exploded Drawing 5615 5615 - 2 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Spare Parts List 5615 Part Description Shaving foil frame Cutter block Cleaning brush Pos. No. 7 8 24 Part Number 5614763 5524761 5524780 This shaver is a non-serviceable item. Refer to the Inventory Recommendations for Non-serviceable Products page in the Braun price book for article numbers when replacing the unit under warranty. 5615 - 3 BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Service Information 5615 Technical Data Principle Housing Shaving head: Cutter block: Long hair trimmer: Drive: Power transmission: Power supply: Amplitude: Revolutions: Working current: Operating capacity: Dismantling Protective caps (1, 22): Remove cleaning brush (24). Take off screw (21). Pull apart the protective caps (1) and (22), and lever them, one after the other, from the housing shelves. To be unlocked through unlocking pins and to be removed. To be extracted. Remove circlip (9). Take off cutter block support (10) with ring seal and conical coil spring (11). 5615 - 4 Battery operated shaver with switch-on protection and foldable long hair trimmer. Plastic material Plastic frame with integrated shaving foil. 30 blades, 3° inclined, 10 mm diameter, plastic frame. Integrated in the housing upper part; can be additionally switched on by a separate slider. 2.7 V DC motor. via eccenter and oscillating frame onto the shaving system. by 2 Mignon batteries 1.5 V (type LR6, AM3, MN 1500/AA alkaline) Approx. 2.3 mm, measured at the cutter block. Approx. 6200 r.p.m. (with new batteries) Approx. 5500 r.p.m. (by 2.4 V minimum) Approx. 500 mA (without long hair trimmer) Approx. 60 shaving minutes. Shaving foil frame (7): Cutter block (8): Cutter block support (10): BINC Rev: 4/97 BAG Rev: 1/97 Service Documentation Service Information 5615 Remove batteries. Unscrew the 3 housing screws (19). By means of a grip ring pliers inserted into the battery box, press apart the housing shelves (3) and (20), one after the other (see exploded drawing "A"). Attention: When opening the housing shelves, the spring catches (17) will snap out. Before extracting the motor, the slider (2) must be switched in the 'on' position. Snap out the motor from the direction of the eccenter and remove it together with the minus contact. Attention: When extracting the motor please take care that the spring wire (15) does not get lost. (Mostly the wire sticks to the motor through the magnetic effect.) All further dismantling steps do not require further explanation. Open housing: Motor (16): Reassembly The reassembly is made in reversed order. Attention must be paid to the following: Battery contacts (13, 14): Before inserting the plus contact (14) into the housing upper part (3), please absolutely make sure that the slider (2) is adjusted in the 'on' position. Wh

File name 5629.pdf

Service Documentation Braun 3610, 3612, 3615 Interface Market Release 5/99 5629 5629 BINC Rev: 4/99 BAG Rev: 2/99 Service Documentation Exploded Drawing 5629 5629 - 2 BINC Rev: 4/99 BAG Rev: 2/99 Service Documentation Spare Parts List 5629 Part Description Protective cap Shaving foil frame (black) Cutter block Small part sct includes: 4a, 4b, 4c, 4d, 4e, 4f, 4g Housing, black (3612) Housing, blue (3610) Housing, silver (3615) PCB, 1 hr. charge (3612, 3615) PCB, 16 hr. charge (3610) Motor Cleaning brush Pos. No. 1 2 3 4 5 5 5 6 6 7 Part Number 5628625 5628762 5524761 5628634 5629642 5629643 5629644 5629632 5629633 5628628 5503120 5629 - 3 BINC Rev: 4/99 BAG Rev: 2/99 Service Documentation Service Information 5629 General: Nominal voltage: Nominal frequency: Housing: Shaving foil frame: Cutter block: Rechargeable and cord shaver 100 - 240 V 16 hr. / 12 ­ 240 V 1 hr. 50 - 60 Hz Plastic material Plastic with intergrated shaving foil and floating system Plastic frame with 30 outer blades in a 3° angled position, 10 mm diameter 2.4 mm (measured at the cutter block) additionally switchable by a central switch Via 1.2 V DC motor After min 3 minutes recharging time. min 6,000 rpm without LHT. min. 5,500 rpm with LHT Via eccenter and oscillating frame onto the shaving system By a built in rechargeable NiMH battery resp. a built in battery charger with attachable power cord is indicated by a green lamp 3610, 1 Watt 3612, 3615, 4 Watts 3610, approx. 16 hours 3612, 3615 approx. 1 hour Approx. 30 shaving minutes (after full recharge). Technical Data Amplitude: Long hair trimmer: Drive: Revolutions when run on: batteries: Power transmission: Power supply: Charging of the shaver: Power consumption: Charging time: Operating capacity: 5629 - 4 BINC Rev: 4/99 BAG Rev: 2/99 Service Documentation Service Information 5629 Shaving foil frame (2) Unlock via buttons A and remove Cutter block (3) Snap out Dismantling Cutter block support Remove circlip (4a) Take off cutter block with seal (4b) and pressure spring (4c) Housing (5) Remove housing screws (4d) Snap out the carrier unit C to the top (see dashed line) and remove it PCB (6) Remove insulating foil (4g) Now take off PCB (6) together with mains socket Desolder the connecting wires from the motor Remove the oscillating frame from the housing back. Unscrew both screws (4f) Usually the motor wire (4e) sticks to the motor (7) due to the magnetic field In some shavers of the first series, the motors were glued. These shavers have to be modified to meet the new standards with screw connections. Motor (7) Attention! Note: 5629 - 5 BINC Rev: 4/99 BAG Rev: 2/99 Service Documentation Service Information 5629 Reassembly The reassembly has to be made in reversed order. Attention is to be paid to the following points: Motor (7) Before reasssembling the motor (7), insert the motor wire (4e) as shown in the diagram. Slightly greasethe motor in the center. Fix the motor by means of both screws (4

File name 5666.pdf

Service Documentation Lady Braun elegance 3 Market Release 1/85 5666 5666 BINC Rev: 7/96 BAG Rev: 1/85 Service Documentation Exploded Drawing 5666 5666 - 2 BINC Rev: 4/97 BAG Rev: 6/92 Service Documentation Spare Parts List 5666 Part Description Protective cap Frame, white Shaving foil Housing upper part Damping pad 22 x 15 Coupling rod Switch knob Screw Spring catch Spring 3000 series cutter block Circlip Cutter block support Conical coil spring Foam rubber seal Adjustable spring seal Oscillating spring Motor Insulating plate Screw Circuit board, cpl. with sockets with pins Housing lower part, white Housing screw Damping pad Coiled cord Brush Case, cpl. Pos. No. 1 2 3 16 17 19 20 27 28 29 32 33 35 37 41 42 47 48 49 51 Part Number 5666058 5666621 5666760 5666861 5209018 5860049 5666084 5420158 5660028 5660029 order by description 0107001 5666862 5666055 5410179 5300048 5300148 5667626 5420011 5424116 5666848 NLA 5666821 5660111 5260029 5001979 5002849 5666068 53 56 - 5666 - 3 BINC Rev: 7/96 BAG Rev: 5/88 Service Documentation Service Information 5666 Dismantling: Disconnect power cord and remove shaving head frame Unscrew the two housing screws, raise the cover slightly at the top and release the cover by moving the latter towards the bottom. When conducting the oscillating spring adjustment take caution the opened up shaver is always switched on. After having loosened screws (49) remove motor with printed circuit board from the housing lower part and disconnect circuit from the motor. Reassembly: Reconnect circuit board to the motor and place the unit into the housing lower part and tighten screws. Important! Push the switch button to position "1" before remounting the housing upper part, place the upper part at the top in the housing lower part and then close the housing at the bottom. Ensure that the rubber seal is seated correctly in the housing recesses. Finally retighten the two housing screws. Carry out final test. Attention! From May 1988 on, the way of contacting motor to PCB will be changed. The motor will be furnished with sockets and the PCB with corresponding pins. After running out of inventory, in case of a defect only motors of the new version will be delivered. In this case, also the PCB must be replaced. The PCB in the previous design can still be delivered in the future. If the PCB becomes defective, only this component needs to be exchanged. 5666 - 4 BINC Rev: 7/96 BAG Rev: 8/88 Service Documentation Service Information 5666 Description of shaver Cord shaver: Housing: Shaving head frame: Shaving foil: Cutter block: Long-hair trimmer: Drive: Weight of shaver: Technical Data Air-gap between stator and oscillating armature: Lead angle: Resonance frequency: Amplitude at the cutter block: Amplitude at the oscillating arm: 0.15-0.2 mm (gap cannot be altered) 0.8-1.2 mm 65-67 c/s 3-3.5 blades (3-3.5 mm) 120/220 VAC 60 c/s, switch-selected Plastic Plastic with two riveted long-hair trimmer Frame version plastic, 10

File name 5667.pdf

Service Documentation Lady Braun elegance 2 Market Release 1/85 5667 5667 BINC Rev: 7/96 BAG Rev: 1/85 Service Documentation Exploded Drawing 5667 5667 - 2 BINC Rev: 7/96 BAG Rev: 9/92 Service Documentation Spare Parts List 5667 Part Description Protective cap Frame, white Frame, brilliant white Shaving foil Housing upper part, white brilliant white Damping pad Coupling rod Switch knob, white brilliant white Screw 5 Spring catch Spring 3000 series cutter block Circlip Cutter block support Conical coil spring Foam rubber seal Adjustable spring seat Oscillating spring Motor Insulating plate Screw Circuit board, cpl. with sockets with pins Housing lower part, white brilliant white Housing screw Coiled cord Brush Bag Pos. No. 1 2 2 3 16 17 19 20 27 28 29 32 33 35 37 41 42 47 48 49 51 53 56 Part Number 5666086 5667621 5667622 5666760 5666861 NLA 5209018 5660049 5666084 5666127 5420158 5860028 5660029 order by description 0107001 5666862 5666055 5410179 5300048 5300148 5667626 5420011 5424116 5667854 5667856 5666821 5868891 5860111 5001981 5002849 5661001 5667 - 3 BINC Rev: 7/96 BAG Rev: 8/88 Service Documentation Service Information 5667 Description of shaver Cord shaver: Housing: Shaving head frame: Shaving foil: Cutter block: Long-hair trimmer: Drive: Weight of shaver: Technical Data Air-gap between stator and oscillating armature: Lead angle: Resonance frequency: Amplitude at the cutter block: Amplitude at the oscillating arm: 0.15-0.2 mm (gap cannot be altered) 0.8-1.2 mm 65-67 c/s 3-3.5 blades (3-3.5 mm) 120/220 VAC 60 Hz Plastic Plastic with one riveted long-hair trimmer Frame version plastic, 10 mm diameter 38 mm wide. 36 cutter blades, 3° obliquely positioned Simultaneous running trimmer One radius-shaped cutting system 34 mm wide. Oscillating armature motor, solderless connection 225 grams Adjustment of the shaver is achieved by turning the oscillating spring. Check lead angle if necessary readjust. Current consumption 120 V: Active power: Reserve power: 180-215 mA 5-7 W 1W All measurements are taken with mounted shaving head frame. 5667 - 4 BINC Rev: 7/96 BAG Rev: 5/88 Service Documentation Service Information 5667 Dismantling: Disconnect power cord and remove shaving head frame. Unscrew the two housing screws, raise the cover slightly at the top and release the cover by moving the latter towards the bottom. When conducting the oscillating spring adjustment take caution the opened up shaver is always switched on. After having loosened screws (49) remove motor with printed circuit board from the housing lower part and disconnect circuit from the motor. Reassembly: Reconnect circuit board to the motor and place the unit into the housing lower part and tighten screws. Important! Push the switch button to position "1" before remounting the housing upper part, place the upper part at the top in the housing lower part and then close the housing at the bottom. Ensure that the rubber seal is seated correctly in the housing recess

File name 5704.pdf

Service Documentation Braun flex integral 6550 ultra speed Market Release 11/97 5704 5704 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Exploded Drawing 5704 5704 - 2 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Spare Parts List 5704 Part Description Protective cap Shaving foil frame Cutter block Swivel frame Sealing plate Bearing screw Screw Head carrier Lower frame Chassis; with no. 11 to 16 Locking pin Spring Lever Spring Latch Motor PCB Cover Hood Sliding plate Lever Leg spring Leg spring Transmission lever Seal Display Contact strip Cord socket, cpl. Contact spring Housing case Locking button Display window End cap Screw Plug pin Coiled cord Cleaning brush Case Pos. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part Number 5503074 5505765 5504766 5504630 5503014 5504046 5504099 5504631 5505032 5504639 5504087 5504200 5504089 5504090 5504926 5704627 5704625 5504638 5504112 5705636 5504093 5504095 5504092 5504091 5504059 5704634 5504057 5505638 5504067 5704628 5704036 5704635 5704642 5586038 5705055 5002704 5503120 5478830 5704 - 3 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Service Information 5704 Description of shaver Principle Battery power supply with eco-friendly nickel-hydride batteries. Oscillating head with triple shaving system. Long hair trimmer can be additionally switched on. Charging and battery display. Plastic material, chromium-plated. Plastic material with integrated shaving foil and medium trimmer, can be snapped off by means of a push-button switch. Plastic material blades 2 x 27, diameter 6 mm. Can be activated by means of a central sliding plate. 2.4 V d.c. motor. Via eccenter and oscillating frame onto the shaving system. By 2 built-in, rechargeable batteries resp. automatically by a built-in battery charger and independently from the mains voltage or frequency. Multifunctional display: Housing Shaving head frame: Hollow cutter block: Long hair trimmer: Drive: Power transmission: Power supply: Display 1. Batteries are empty. The device is in the process of being charged (green LED) is illuminated. 2. After approx. 60 minutes of charging, the batteries are recharged. Green LED turns off. 3. Figure < 9 > indicates that 9 minutes remain for shaving. The red LED is blinking when the shaver is switched on. 4. Cleaning symbol (see use instructions). 5704 - 4 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Service Information 5704 The device is provided with automatic battery maintenance, i.e. it discharges automatically once a year in order to regain the full battery capacity. This process takes approx. 7 hours. Opening the shaver, described hereafter, destroys the device and has only to be done at the end of the device's lifetime. The cord socket (29) is provided with a screw mechanism to ensure easy recycling. Open the housing by piercing and turning the mechanism (e.g. with a coin). Now, the batteries can be removed and orderl

File name 5705.pdf

Service Documentation Braun flex integral 6515/6520 ultra speed Market Release 3/98 5705 5705 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Exploded Drawing 5705 5705 - 2 BINC Rev: 5/99 BAG Rev: 8/97 Service Documentation Spare Parts List 5705 Part Description Protective cap 5000 series shaving foil frame 5000 series cutter block Swivel frame (black) Swivel frame (silver) Sealing plate Bearing screw Screw Head carrier (black) Head carrier (silver) Lower frame Chassis with no. 11, 12, 15, 16 Locking pin Spring Lever Spring Latch Switch Motor PCB, cpl. Cover, cpl. Hood Sliding plate; w/no. 22 to 25 Lever Leg spring Leg spring Transmission lever Light insert Cord socket, cpl. Housing case; with no. 29 (black) Housing case; with no. 29 (silver) Locking button End cap (dark gray) End cap (silver) Screw Plug pin (gray) Cleaning brush Coiled cord Case Pos. No. 1 2 3 4 4 5 6 7 8 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28 29 30 30 31 32 Part Number 5503074 order by description order by description 5505633 5504630 5503014 5504046 5504099 5505634 5504631 5505032 5504639 5504087 5504200 5504089 5504090 5504926 5504962 5704627 5505631 5504638 5504112 5705636 5504093 5504095 5504092 5504091 5505043 5505638 5705632 5704628 5705012 5705637 5705640 5586038 5704055 5503120 5323015 5504852 5705 - 3 BINC Rev: 11/97 BAG Rev: 8/97 Service Documentation Service Information 5705 Description of shaver Principle Battery power supply with eco-friendly nickel-hydride batteries. Oscillating head with triple shaving system. Long hair trimmer can be additionally switched on. Charging and battery display. Plastic material, chromium-plated.. Plastic material with integrated shaving foil and medium trimmer, can be snapped off by means of a push-button switch. Plastic material, blades 2 x 27, diameter 6 mm. Can be activated by means of a central sliding plate. 2.4 V d.c. motor. via eccenter and oscillating frame onto the shaving system. by 2 built-in, rechargeable batteries resp. automatically by a built-in battery charger and independently from the mains voltage or frequency. Housing Shaving head frame: Hollow cutter block: Long hair trimmer: Drive: Power transmission: Power supply: Display LED, green Charging light - illuminates by connecting to the mains - flashes in 3 minute-intervals by fully charging batteries Low-charge light - illuminates by battery capacity less than 20 % LED, red Maintenance of the battery In order to maintain the maximum capacity of the rechargeable cell unit, it should be discharged about every 6 months by shaving. Then fully recharged for approx. 4 hours from the mains. Do not keep the shaver connected to the mains for a long period of time (i.e. several weeks) Disposal of the batteries Opening the shaver, described hereafter, destroys the device and has only to be done at the end of the device's lifetime. The cord socket (27) is provided with a screw mechanism to ensure an easy recycling. Open the housing

File name shvcross.pdf

Type - to - Model Cross-Reference Shavers Type Number Micron Series 5422 5428 5556 5563 Single Foil Series 5235 5462 5463 5464 5533 5596 5597 2000 series 5459 5461 3000 series 5419 5424 5469 5470 5564 5567 5569 5579 4000 series 5403 5471 5501 5502 5580 5584 5584/28 5585 5585/09 5586 Model Number(s) 10/00 eltron 900, 2101 2005 2505, 2515 2501 240 linear 105 corded 105, 100 entry 209, 205 entry 260, 270 linear 259, 255 entry 155, 150 entry 2060 entry 2040, 2035 entry 3025 system 1-2-3 3012 system 1-2-3 3010 cord 3550 universal 3512 system 1-2-3 3525 system 1-2-3 3510 system 1-2-3 action line system 1-2-3 4005 flex control corded 4501 flex control 4505 flex control 4504 flex control 4550 flex control 4510 flex control 4510 flex control 4520 flex control 4520 flex control 4525 flex control 5000 series 5465 5466 5468 5476 5477 5478 5503 5504 5505 5506 5507 6000 series 5703 5704 5705 7000 series 5494 5493 5492 5491 Clean & Charge 5301 Interface Shavers 5629 Pocket Shavers 5523 5524 5525 5614 5615 Lady Shavers 5666 5567 5315, 5316 flex integral 5314 flex integral 5505 flex integral 5414 flex integral 5415 flex integral 5416 flex integral 5525 flex integral 5550 flex integral 5515, 5520 flex integral 5510 flex integral 5015 flex integral 6525 flex integral ultra 6550 flex integral ultra 6515, 6520 flex integral ultra 7505 Syncro 7526 Syncro 7546 Syncro 7570 Syncro SCC1 Clean and Charge system 3610, 3612, 3615 pocket battery pocket battery deluxe pocket battery deluxe traveler 350 pocket twist 375 pocket twist plus lady elegance 3 lady elegance 2 Hair Removers - Silk Epil 5271 5285 5291 5292 5296 5303 5304 5305 5306 EE 10 EE 1 EE 10 , duo plus EE 30 , duo rechargeable EE 100 / ER 100 EE 1070, 1170 ER 1270, 1373 EE 1570, 1670 ER 220 Beard Trimmers 5280 5281 5601 exact universal exact 6 memory universal EP 100, 80, 60 Shaver Model - to - Type Cross-Reference Model Number 105 corded 105, 100 entry 155, 150 entry 2005 2040, 2035 entry 2060 entry 209, 205 entry 240 linear 2501 2505, 2515 259, 255 entry 260, 270 linear 350 pocket twist 375 pocket twist plus 3010 cord 3012 system 1-2-3 3025 system 1-2-3 3510 system 1-2-3 3512 system 1-2-3 3525 system 1-2-3 3550 universal 3610 interface 3612 interface 3615 interface 4005 flex control corded 4501 flex control 4504 flex control 4505 flex control 4510 flex control 4510 flex control 4520 flex control 4520 flex control 4525 flex control 4550 flex control 5005 flex integral cord 5015 flex integral 5314 flex integral 5315 flex integral 5316 flex integral 5414 flex integral 5415 flex integral 5416 flex integral 5510 flex integral 5515 flex integral 5520 flex integral 5525 flex integral 5550 flex integral 6515 flex integral ultra 10/00 Type Number 5462 5463 5597 5428 5461 5459 5464 5235 5563 5556 5596 5533 5614 5615 5469 5424 5419 5569 5564 5567 5470 5629 5629 5629 5403 5471 5502 5501 5584 5584/28 5585 5585/09 5586 5580 5468 5507 5466 5465 5465 5476 5477 5478 5506 5505 5505 5503 5504 5705 6520 flex int