sony KV-13FS100 free download

File name KV-13FS100 Diagrama Sony Wega de curso.pdf

TECNICAS PARA REPARAR LOS NUEVOS TELEVISORES DE PANTALLA PLANA MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO. $'-8670(17 ,7(06 2)  A BOARD WAVEFORMS Range (DEC) 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-63 00-255 00-01 00-63 00-15 00-03 00-01 00-01 00-01 00-07 00-01 00-03 00-03 00-03 00-03 00-01 00-01 00-255 00-15 00-01 Initial Data 24 24 37 28 42 28 33 35 34 18 32 32 128 0 11 35 0 0 1 0 3 1 1 0 3 0 0 0 5 6 0 SECTION 4: CIRCUIT ADJUSTMENTS DEVICE "DEF" Item# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 OSD HSIZ HPOS VSIZ VPOS VLIN SCOR VBOW VANG TRAP PAMP UPIN LPIN TROT HBLK LBLK RBLK VBLK HMSK HDW AFC AFC1 AFCW CDMD HSS VSS SLDN SLUP JPSW HOSC EHT EHTG DETAIL H SIZE(EW DC) H POSITION V RAMP SIZE V POSITION(RAMP DC)not useful V LINEARITY S CORRECTION BOW ANGLE EW TRAPESIUM EW PIN UPPER PIN LOWER PIN TROT H BLK mode select HBLK front timing HBLK rear timing V BLK width TOP VEND(when MACROVISION)prevent OFF H PULSE WIDTH(25u/19u) AFC GAIN AFC1 TIME CONSTANT AFC1 PULL IN WIDE V DET WINDOW SW TIMING SYNC SLICE LEVEL(H sepa) SYNC SLICE LEVEL(V sepa) Auto Slice level DOWN Auto Slicelevel UP Jump SW H VCO fo ADJUST EHT EHT MODE 22 1 2 3 4 ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y173) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator 2.1 Vp-p (H) 5 6 3.2 Vp-p (H) 7 1.2 Vp-p (H) 8 0.9 Vp-p (H) KV-13FS100 KV-13FS100 KV-13FS110 KV-13FS110 KV-14FV300 KV-14FV300 4-1. SETTING THE SERVICE ADJUSTMENT MODE 1. Standby mode (Power off). 2. Press the following buttons on the remote commander within a second of each other: Channel 5 Sound Volume + Power Display RM-Y173 RM-Y173 RM-Y173 RM-Y173 RM-Y173 RM-Y173 US CND US CND LATIN NORTH LATIN SOUTH SCC-S61F-A SCC-S59E-A SCC-S61E-A SCC-S59F-A SCC-S60M-A SCC-S60N-A 4-2. MEMORY WRITE CONFIRMATION METHOD 1. After adjustment, pull out the plug from the AC outlet, then replace the plug in the AC outlet again. 2. Turn the power switch ON and set to Service Mode. 3. Call the adjusted items again to confirm they were adjusted. 1.0 Vp-p (H) 9 10 1.0 Vp-p (V) 11 4.7 Vp-p (H) 12 2.4 Vp-p (H) 4-1-1. SERVICE ADJUSTMENT MODE ON 1. The CRT displays the item being adjusted. 4-3. REMOTE ADJUSTMENT BUTTONS AND INDICATORS POWER (Service Mode) Mode Category service Signal Type ntsc vchp 00000000 defl Display Item Item Data MUTING hsiz 16 (Enter into memory) DISPLAY (Service Mode) 3 Item (Data up) 6 Item (Data down) 5 (Device item down) 168.8 Vp-p (H) 13 14 28.7 Vp-p (H) 15 1.14K Vp-p (V) 16 1.0 Vp-p (H) 00000000 1 Disp. (Item up) 2 (Device Item Up) 2. Press 1 or 4 on the Remote Commander to select the item. 3. Press 3 or 6 on the Remote Commander to change the data. 4. Press MUTING then ENTER to write into memory. DEVICE "16:9" Item# 1 2 3 4 5 OSD PAMP UPIN LPIN ACLV ABLV EW PIN UPPER PIN LOW