File information: | |
File name: | Samsung_CN331_3339_501_5039_5085.pdf [preview CN3339VB] |
Size: | 2724 kB |
Extension: | |
Mfg: | SAMSUNG |
Model: | CN3339VB 🔎 |
Original: | KCT12A 🔎 |
Descr: | diagrama electrico |
Group: | Electronics > Consumer electronics > TV |
Uploaded: | 18-02-2009 |
User: | gama1224 |
Multipart: | No multipart |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 1 | |
File name Samsung_CN331_3339_501_5039_5085.pdf COLOR TELEVISION RECEIVER Chassis : Model: K15B CN331EBZX/DIS CN501EBZX/DIS CN331EBZX/XAP CN501EBZX/XAP CN3339BZX/XAP CN5039BZX/XAP CN5085BZX/DRI COLOR TELEVISION RECEIVER CONTENTS 1. Precautions 2. Specifications and IC Data 3. Disassembly and Reassembly 4. Alignment and Adjustment 5. Troubleshooting 6. Exploded View and Parts List 7. Electric Parts List 8. Block Diagram 9. PCB Layout Diagram 10. Wiring Diagram 11. Schematic Diagrams ELECTRONICS © Samsung Electronics Co., Ltd. OCT. 1998 Printed in Korea 3K15B-0102 Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which peopleÑparticularly childrenÑmight insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test. DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) LEAKAGE CURRENT TESTER (READING SHOULD NOT BE ABOVE 0.5mA) EARTH GROUND Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unitÕs AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these als |
Date | User | Rating | Comment |