SONY DVP-S300 free download

File name DVP-S300.pdf

DVP-S300/S305/S315 SERVICE MANUAL E Model RMT-D103E/105A/105P US Model DVP-S300 DVP-S300/S305 AEP Model DVP-S315 UK Model DVP-S315 Chinese Model DVP-S305 Taiwan Model DVP-S305 Singapore Model DVP-S305 SPECIFICATIONS CD/DVD player Signal format system PAL/ (NTSC): DVP-A305/S315 NTSC : DVP-S300 General Power requirements Power consumption DVD (PCM 96 kHz): 2 Hz to 44 kHz (+0.5 dB, ­2.0 dB) DVD (PCM 48 kHz): 2 Hz to 22 kHz (±0.5 dB) CD: 2 Hz to 20 kHz (±0.5 dB) More than 107 dB (LINE OUT (AUDIO) connectors only) Less than 0.0028% More than 100 dB (DVD) More than 97 dB (CD) Less than detected value (±0.001% W PEAK) Dimensions (approx.) 220 ­ 240 V AC, 50 Hz: DVP-S305/S315 120 V AC, 60 Hz: DVP-S300 22 W: DVP-S305/S315 20 W: DVP-S300 430 Ч 95 Ч 325 mm (17 Ч 33/4 Ч 127/8 in.) (w/h/d): DVP-S300/S315 430 Ч 95 Ч 330 mm (w/h/d): DVP-S305 incl. projecting parts 4.0 kg (8 lb 13 oz) 41 °F to 95 °F (5 °C to 35°C) 5% to 90% Audio characteristics Frequncy response Signal-to-noise ratio Harmonic distortion Dynamic range Mass (approx.) Operating temperature Operating humidity Wow and flutter Outputs and inputs jack type LINE OUT (AUDIO) DIGITAL OUT (OPTICAL) DIGITAL OUT (COAXIAL) LINE OUT (VIDEO) S VIDEO OUT Phono jacks Optical output connector Phono jacks Phono jack 4-pin mini DIN Phone jack Output level Load impedance Supplied accessories · Audio/video/S-link connecting cord (1) (DVP-S300: US) · Audio/Video connecting cord (1) (DVP-S300: E/S305/S315) · S video cable (1) · Remote commander (remote) RMT-D103E (1) (DVP-S305) · Remote commander (remote) RMT-D105A (DVP-S300) · Remote commander (remote) RMT-D105P (DVP-S315) · sony R6 (size AA) batteries (2) Design and specifications are subject to change without notice. 2 Vrms Over 10 kilohms (at 50 kilohms) ­18 dBm Wave length: 660 nm 0.5 Vp-p 1.0 Vp-p 75 ohms terminated 75 ohms, sync negative Y: 1.0 Vp-p 75 ohms, sync negative C: 0.3 Vp-p 75 ohms terminated 12 mW 32 ohms PHONES CD/DVD PLAYER MICROFILM SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 6. Check the B+ voltage to see it is at the values specified. 7. Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage.