PANASONIC TC-CT-F2121 ch.GL1 free download

File name PANASONIC TC-CT-F2121 ch.GL1.pdf

ORDER NO. MTV0701517CE Colour Television TC-21GX30P GL1 Chassis Specifications Power Source : Power Consumption : Aerial Impedance : Receiving System : Receiving Channels : VHF UHF CATV Audio Terminal : DVD Y PB PR AV 1, 2 Video In Audio In Monitor Out 1 Vp-p, 75 Approx. 0.5V, 47k Specifications are subject to change without notice. Mass and dimensions shown are approximate. 1.0 Vp-p, 75 0.7 Vp-p, 75 0.7 Vp-p, 75 Mass : 2-13(U.S.A Standard) 14-69(U.S.A Standard) 1-125(U.S.A Standard) Audio Output : Dimensions : AC AUTO 110-240V, 50/60 Hz 58W 75 unbalanced Coaxial type 17 Systems Picture Tube : High Voltage : Video Out Audio Out 1 Vp-p, 75 Approx. 0.5V, 1k 27.5kV ±1.5 at zero beam current A51LYZ395X65 50.5cm (21 inches) Measured diagonally, 90° deflection 5W + 5w = 10W Height : 472 mm Width : 598 mm Depth : 479 mm 22.5 kg (Net Wt.) © 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. TC-21GX30P CONTENTS Page 1 Safety Precautions 1.1. General Guide Lines 1.2. Leakage Current Cold Check 1.3. Leakage Current Hot Check (Fig. 1) 1.4. X-Radiation 1.5. GL1 Chassis Block Diagram 2 Service Hints 2.1. Service Position for E-Board 2.2. Factory Mode Adjustment 2.3. Adjustment for White Balance 3 3 3 3 3 4 5 5 5 8 2.4. Adjustment for CRT CUT OFF 2.5. Adjustment Procedure 2.6. Adjustment 3 Conductor Views 4 Schematic Diagram 4.1. A Board 4.2. L Board 5 Parts Locations 6 Replacement Parts List 6.1. Replacement Parts List Page 8 9 10 13 14 16 21 24 25 26 2 TC-21GX30P 1 Safety Precautions 1.1. General Guide Lines 1. It is advisable to insert an isolation transformer in the AC supply before servicing this hot chassis. 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations, are properly installed. 4. When the receiver is not to be used for a long period of time, unplug the power cord from the AC cord outlet. 5. Potential, as high as 29.0kV is present when this receiver is in operation. Operation of the receiver without the rear cover involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by anyone who is not thoroughly familiar with the precautions necessary when working on high voltage equipment. Always discharge the anode of the picture tube to the receiver chassis before handling the tube. After servicing make the following leakage current checks to prevent the customer from being exposed to shock hazards. 1.2. Leakage Current Cold Check 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Turn on the receiver's power switch. Measure the resistance value, with an ohmmeter, between the jumper AC