File information: | |
File name: | digital_camera_©_.part1.rar [preview MVC-FD88 [MVC FD83]] |
Size: | 2387 kB |
Extension: | |
Mfg: | SONY |
Model: | MVC-FD88 [MVC FD83] 🔎 |
Original: | by salvacolnome 🔎 |
Descr: | Service Manual Digital Still Camera [ver. 1.0 1999.05] - part 1/3 (pag.19) |
Group: | Electronics > Consumer electronics > Photo > Digital cameras |
Uploaded: | 07-11-2009 |
User: | salvacolnome |
Multipart: | 0 1 2 |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 1 | |
File name MVC-FD83_88.pdf MVC-FD83/FD88 SERVICE MANUAL Ver 1.0 1999. 05 US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model MVC-FD83/FD88 Tourist Model Photo: MVC-FD88 MVC-FD88 This service manual contains information for Japanese model as well. SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM MVC-FD83/FD88 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) · b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) · Through hole is omitted. · Circled numbers refer to waveforms. · There are few cases that the part printed on diagram isn't mounted in this model. · Chip parts. Transistor C 6 5 4 4 5 6 1 2 1 2 3 CD-228 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM Ref. No.: CD-228 board; 2,000 series MVC-FD88 · For Printed Wiring Board. · CD-228 board is 4-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. · There are few cases that the part isn't mounted in this model is printed on this diagram. · Chip transistor C (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. * (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) 1. Connection Pattern box CD-228 BOARD 1 B E Diode 3 3 8.4 Vp-p 125 µsec IC201 1, 2, 3 REC B E 1 2 3 3 2 1 3 2 1 5 4 3 2 1 2 1 2 1 (For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Temperature characteristics External dimensions (mm) · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with 5 differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 1: fusible resistor · C: panel designation · A: B+ Line * · B: B Line * · J : IN/OUT direction of (+,) B LINE. * · C: adjustment for repair. * · Circled numbers refer to waveforms. * * Indicated by the color red. Note : The components identified by mark ! or dotted line with mark ! are critical for safety. Replace |
Date | User | Rating | Comment |