JBL GTO7001 free download

File name Jbl-GTO7001 caramp.pdf

GTO7001 1 CHANNEL POWER AMPLIFIER SERVICE MANUAL JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Released 2007 Discontinued XXXX Rev1 1/2008 GTO7001 - CONTENTS SPECIFICATIONS ...1 PACKING...2 CONTROL/INSTALLATION DRAWINGS...3 CONTROL/INSTALLATION INSTRUCTIONS...4 BASIC TROUBLESHOOTING...5 EXPLODED VIEW/PARTS LIST...6 AMPLIFIER BLOCK DIAGRAM...7 ELECTRICAL PARTS LIST ...8 P.C.B. DRAWINGS...12 IC/TRANSISTOR PINOUTS...16 SCHEMATICS...17 GTO 7001 Specifications Output Power: (14.4V supply) Signal-to-noise ratio: Dynamic power: Frequency response: THD+N 1KHz LPF=22KHz Input Impedance Maximum input signal: Maximum sensitivity: Bass Boost @ 50Hz DC Offset Output regulation: Idle Current @ 4 ohms Max Current Draw Remote Operating Voltages Turn-on delay time Circuit Protection Operating voltage range Dimensions: Fuses: 425W RMS x 1 channels @ 4 ohms; 1% THD + N 700W RMS x 1 channels @ 2 ohms; 1% THD + N 80dBA (reference 1W into 4 ohms) 107dBA (reference rated power into 4 ohms) 900W @ 2 ohms 20Hz ­ 330Hz (­3dB) 0.02% (rated power @ 4 ohms) >20K ohms 6.0V 100mV 0-6dB <30mV .03dB @ 4 ohms 1.2A <58A @ 2 ohms ON 5V OFF 4V 2-3 sec Temperature (80±5C), Short circuit (8-16V) 15 x 10 3/8 x 2 1/8" (380 x 263 x 53mm) (3) x 25A JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice. 1 GTO7001 Item 1 2 3 4 5 6 7 Part Number CH4623221132 BZL311105120 GTO7001 Description Outer Carton Packing Foam Amplifier Plastic bag Plastic bag Owner's manual Accessory kit consisting of: Mounting Screws 25A Fuse Remote Level control Phone cable 4PIN Black L=6M, 6P4C 2 Qty 1 2 1 1 1 1 4 3 1 1 Visit www.jbl.com LS1AA0404501 1601-253G-00 REMOTE GTO AMP 2100-0009-04 GTO7001 4x 2x 1x 1x 1x 3x 10-3/8" 263mm 0 1 2 2-1/8" 53mm 15" 380mm D 34 9 A 8 5 6 7 A B C 1" 25mm B A B C D A 1-5/8" 40mm 8 3 GTO7001 GTO7001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER'S MANUAL Installation Warnings and Tips · Disconnect the negative (­) lead from your vehicle's battery. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. · Choose a safe mounting location away from moisture. · Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. · Mount the amplifier, using the supplied hardware. Specifications · 425W RMS x 1 channel @ 4 ohms and 1% THD + N* ·