SuperStar 2200 free download

File name Super Star 2200.pdf

CHASSIS PCMA001S Superstar 2200 Alan 88S - Argus 5000 - Cobra 148GTL DX (fake)- Colt 2400 - Falcon 2000 - Ham International 8040 HyGain 80 - Lafayette 240FM - Mongoose 2000 - Nato 2000 - Palomar 2400 - Palomar 5000 - TriStar 797 - TriStar 848 Block Schematic Diagram PCB Layout Test Points Reading Point TP1 TP1 TP1 TP1 TP1 TP1 TP2 TP3 TP4 TP4 Adjustment CT1 CT2 CT3 CT4 CT12 CT5 T1 VCO-Coil CT11 CT10 Description Band A -80 Ch. Band B -40 Ch. Band C CEPT Band D + 40 Ch. Band E + 80 Ch. Band C CEPT 0utput to RF local oscillator VCO DC Voltage AM LSB Value 19.655MHz 19.880MHz 20.105MHz 20.330MHz 20.555MHz 20.1035MHz 37.660-38.100MHz for CEPT 2,5 Volt @ 27.175MHz 10.695MHz 10.692MHz Adjustment RECEIVER T8 T9 T10 T11 T12 T13 T14 T6 T7 T16 TRANSMITTER T1 T2 T3 T4 T5 L16 CT8 CT9 RV2 RV11 METER RV4 RV8 RV9 . RV1 RV6 RV11 RV5 Description RF Input RF Input RF Input 1. IF 1. IF AM IF AM Detector SSB IF SSB Detector FM Discriminator PLL Output to Converter PLL Output to Converter Transmitter Output Transmitter Output Transmitter Output Transmitter Output Transmitter Output USB/LSB Transmitter Output USB/LSB Bias Q8 AM/FM Output Power RF Power Meter RF S-Meter RF S-Meter FM Modulation SSB Modulation AM Modulation Carrier at SSB Value 10,7MHz 10,7MHz 455kHz 455kHz 455kHz 37.660 - 38.100MHz for CEPT 37.660 - 38.100MHz for CEPT 26.965 - 27.405MHz for CEPT 26.965 - 27.405MHz for CEPT 26.965 - 27.405MHz for CEPT 26.965 - 27.405MHz for CEPT 26.965 - 27.405MHz for CEPT 26.965 - 27.405MHz for CEPT 10 Watt SSB (USB/LSB) AM/FM +/- 2kHz 18 Watt p-p 90% Adjust for NO Carrier Modification for SuperStar 2200 To get 10-meter, cut trace from + 5 Volt to Pin 8 and 9. To get 12-meter, cut trace from GND to Pin 7 and connect Pin 7 to + 5 Volt. Make a new VCO Block. VCO-Block for CB-Radio Re-tune both Transmitter and Receiver-part. The VCO-Block is a part of the active oscillator in TA7310P. This will opeate between 16MHz and 19MHz. Output from TA7310P Pin 9 to PLL02A is: Mixer frequency - VCO frequency. Output from TA7310P Pin 6 to Receiver/Transmitter Mixer is: Mixer frequency + VCO frequency. The new "VCO-BLOCK" will operate between 14MHz and 21MHz, and will then cover 10-meter, 11meter and 12-meter. Components D1 = BB156 (Phillips) L1 = 5uH C1 = 470pF C2 = 470pF C3 = 4,7pF C4 = 12pF VCO operates between 17.115MHz (Ch.1 Band A) and 18.445MHz (Ch.40 Band E), output on Pin 6 is 36.780MHz (Ch.1 Band A) to 39.000MHz (Ch.40 Band E), and output on Pin 9 is 2.550MHz to 2.110MHz inn all band. The VCO-voltage (TP1) operates between 4,5 Volt (Ch.1 Band A) and 0,5 Volt (Ch.40 Band E). Frequency List Ch. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 A = - 80 26.065 26.075 26.085 26.105 26.115 26.125 26.135 26.155 26.165 26.175 26.185 26.205 26.215 26.225 26.235 26.255 26.265 26.275 26.285 26.305 26.315 26.325 26.355 26.335 26.345 26.365 26.375 26.385 26.395 26.405 26.415 26.425 26.435 26.445 26.455 26.4