Sony MDXJ9000 free download

File name Sony-MXDJ9000 mix.pdf

MX-DJ9000 SERVICE MANUAL US Model AEP Model UK Model E Model This set is the audio mixer in PMPK-DJ9000. SPECIFICATIONS General Power requirements Power consumption Inputs Microphone Phono Line Output power Outputs Frequency range Distortion S/N ratio Talkover attenuation Headphones impeadance Dimensions Mass U.S.A. and Mexico: 120 V AC, 60 Hz European countries: 220 - 230 V AC, 50/60 Hz Other countries: 110 - 120 V/ 220 - 240 V AC, 50/60 Hz 10 W 2 PHONO, 2 LINE, 1 MIC 1.5 mV 3 mV 150 mV 7 V (peak-to-peak) 1 LINE OUT, 1 REC OUT via RCA 20 - 20,000 Hz, ±3 dB Less than 0.08 % 70 dB (1 kHz) ­16 dB 16 Approx. 200 Ч 80 Ч 166 mm (7 7/ 8 Ч 3 1/ 4 Ч 6 5/8 in) (w/h/d) 1.6 kg (3 lb 8 oz) Supplied Accessory AC power adaptor cord (1) Audio cord (without ground wire) (2) Design and specifications are subject to change without notice. AUDIO MIXER 1 TABLE OF CONTENTS 1. GENERAL 2. DIAGRAMS 2-1. 2-2. 2-3. 2-4. Circuit boards Location ... 3 Schematic Diagram ... 4 Printed Wiring Board ­ Main Section ­ ... 5 Printed Wiring Board ­ I/O Section ­ ... 6 ... 3 3. EXPLODED VIEW 3-1. Chassis Section ... 8 4. ELECTRICAL PARTS LIST ... 10 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 2 SECTION 1 GENERAL This section is extracted from instruction manual. SECTION 2 DIAGRAMS NOTE FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM 1 2 3 MIC LEVEL CUE CH-1 0 10 CH-1 PHONO 1 LINE 1 +3 PHONO 2 0 -3 10 10 10 CH-2 0 10 CH-2 LINE 2 Note on Printed Wiring Board: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. · b : Pattern from the side which enables seeing. TALK OVER POWER ON OFF CUE LEVEL Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · U : B+ Line. · V : B­ Line. · Voltages are dc with respect to ground under no-signal conditions. no mark : Power on · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Signal path. F : AUDIO 4 5 6 7 5 0 5 0 9 LEVEL LEVEL 10 -8 -13 L dB R 5 0 5 0 CH-1 GAIN CH-2 0 0 10 0 10 CROSSFADER 10 5 0 CH-2 CH