Denon DNS5000 free download

File name Denon-DNS5000 cd.pdf

For U.S.A., Canada & Europe model SERVICE MANUAL MODEL DN-S5000 TABLE TOP SINGLE CD PLAYER Some illustrations using in this service manual are slightly different from the actual set . 16-11, YUSHIMA 3-CHOME, BUNKYOU-KU,TOKYO 113-0034 JAPAN Telephone: 03 (3837) 5321 X0161V.02 MO/CDM 0302 DN-S5000 2 DISASSEMBLY (Follow the procedure below in reverse order when reassembling) 1. SLIP DISC, SLIP MAT (1) . Remove a screw 69 and pull out Slip Disc and Slip Mat. 69 Washer Slip Disc Slip Mat Slip Sheet Anti-static Sheet 2. PLATTER (1) (2) . Remove Belt from Motor Pully. Remove 3 screws 60 and pull out Platter. 60 Belt 60 Platter Motor Pully 2 DN-S5000 3. DRIVE UNIT (1) (2) (3) . 3 Remove 4 screws 71 and pull out Drive Unit. Disconnect Flat cable and Connector. Detach Drive Unit. Drive Unit 71 71 Connector Flat cable Drive Unit Note: Do not pull out aslant to prevent Flat cable damage. Do not fail to pull AC cord from wall outlet before disconnect the Flat cable and Connector. If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger. 4. COVER UNIT (1) (2) (3) . Remove 5 screws 70 and pull out Cover Unit. Disconnect Connectors. Detach Cover unit. Cover unit CX042 70 70 Connector CX101 CX041 70 Connector CX031 Note: Do not fail to pull AC cord from wall outlet before disconnect Connectors. If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger. 3 DN-S5000 5. SENSOR AND SCALE UNITS OF PLATTER (1) (2) (3) Remove 2 screws 64 and pull out Sensor Cover and Sensor unit. Remove a E Ring. Pull out Scale unit. 64 64 Sensor Cover Sensor unit E Ring Scale unit 4 6. SENSOR AND SCALE UNITS OF SLIP DISC (1) (2) . Remove 2 screws 64 and pull out Sensor Cover and Sensor unit. Remove a screw 60 and pull out Scale unit. Scale unit 60 64 64 Sensor Cover Sensor unit 7. POWER PWB (1) . Remove 5 screw 51 and pull out Power PWB. 51 Power PWB 51 4 DN-S5000 8. DSP PWB UNIT (1) . 5 Remove 9 screws 52 and pull out DSP PWB unit 52 DSP PWB unit 52 52 9. DRIVE COVER (1) . Remove 4 screws 12 and pull out Drive cover. 19 Drive cover 19 19 19 10. DRIVE (1) (2) (3) . Move Drive Rack in arrow direction through the Hole on the bottom chassis. Loader frame comes out. Pull up Loader panel while pulling it towards front. Remove 4 screws 6 and pull out Drive. Drive 4 6 6 4 5 DN-S5000 6 BLOCK DIAGRAM 1 2 3 4 5 6 7 8 DN-S5000 -HB,F1,F2 GND,+5,+9 A LEDdriver 128Mb SDRAM ROM DRIVE ATAPI INTERFACE 128Mb SDRAM D16 ~ 31 TFS0 TCK0 TXD0A TXD0B 33M LRCK BCLK MAIN1 MON1 main out BU2090 AMP10 8CH D/A PCM1608 mon out ADRESS ADSP21065L PANEL µcom LEDdriver DSP SHOCK PROOF TXD1B AMP11 BU2090 DIT SM5902 384fs MAIN DOUT main digital out TMP86CM47U ROM32k RAM1k RAM control ATAPI interface TFS1 TCK1 TXD1A LED out Key scan VR in B BUS select DMA 16Bit Bus D0 ~ D15 MON DOUT CONTROL DIT SM5902 moni digital out FLAG D0 DISC CP