Sony XM1004GX free download

File name Sony-XM1004GX caramp.pdf

XM-1004GX SERVICE MANUAL Ver 1.1 2001.05 US Model SPECIFICATIONS AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 75 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Speaker impedance 2 ­ 8 (stereo) 4 ­ 8 (when used as a bridging amplifier) Maximum outputs Four speakers: 170 W Ч 4 (at 4 ) Three speakers: 170 W Ч 2 + 400 W Ч 1 (at 4 ) Two speakers: 400 W Ч 2 (at 4 ) Rated outputs (supply voltage at 14.4 V) Four speakers: 75 W Ч 4 (20 Hz ­ 20 kHz, 0.04% THD, at 4 ) 100 W Ч 4 (20 Hz ­ 20 kHz, 0.1% THD, at 2 ) Two speakers: 200 W Ч 2 (20 Hz ­ 20 kHz, 0.1% THD, at 4 ) Frequency response 5 Hz ­ 50 kHz ( +0.5 dB) ­3 Harmonic distortion 0.005% or less (at 1 kHz, 4 ) Circuit system Input level adjustment range 0.2 ­ 6.0 V (RCA pin jacks) 0.4 ­ 12.0 V (High level input) High-pass filter 50 ­ 300 Hz, ­12 dB/oct Low-pass filter 50 ­ 300 Hz, ­12 dB/oct Low boost 0 ­ 10 dB (40 Hz) Phase shift adjustment range 0° ­ 180° (at 40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 ­ 16 V Current drain at rated output : 40 A (4 ) Remote input : 1.5 mA Dimensions Approx. 358 Ч 50 Ч 264 mm (w/h/d) (14 1/8 Ч 2 Ч 10 1/2 in.) not incl. projecting parts and controls Mass Approx. 3.5 kg (7 lb. 11 oz.) not incl. accessories Supplied accessories Mounting screws (4) Design and specifications are subject to change without notice. Notes on Chip Component Replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. STEREO POWER AMPLIFIER 9-873-520-11 2001E0400-1 © 2001.5 Sony Corporation e Vehicle Company Shinagawa Tec Service Manual Production Group 1 XM-1004GX TABLE OF CONTENTS 1. GENERAL Location and Function of Controls ... 3 Connections ... 4 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. Plate, Bottom ... 6 AMP Board Section ... 6 AMP Board, Filter (A) Board, Filter (B) Board ... 7 LED Board ... 7 3. ELECTRICAL ADJUSTMENT ... 8 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. 4-5. Block Diagram ... 9 Printed Wiring Board ­AMP Section­ ... 11 Schematic Diagram ­AMP Section (1/2)­ ... 12 Schematic Diagram ­AMP Section (2/2)­ ... 13 Schematic Diagram ­Filter (A), Filter (B), LED Secti