Sony XMSD46X free download

File name Sony-XMSD46X caramp.pdf

XM-SD46X SERVICE MANUAL Ver. 1.0 2004. 12 US Model Canadian Model AEP Model UK Model E Model SPECIFICATIONS AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 60 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Suitable speaker impedance 2 ­ 8 (stereo) 4 ­ 8 (when used as a bridging amplifier) Maximum outputs Four speakers: 120 W Ч 4 (at 4 ) 150 W Ч 4 (at 2 ) Three speakers: 120 W Ч 2 + 300 W Ч 1 (at 4 ) Rated outputs (supply voltage at 14.4 V) Four speakers: 60 W RMS Ч 4 (20 Hz ­ 20 kHz, 0.08% THD + N, at 4 ) 75 W RMS Ч 4 (20 Hz ­ 20 kHz, 0.1% THD + N, at 2 ) Three speakers: 60 W RMS Ч 2 + 150 W RMS Ч 1 (20 Hz ­ 20 kHz, 0.1% THD + N, at 4 ) SN Ratio 97 dBA (Reference 1W into 4 ) Frequency response 5 Hz ­ 50 kHz ( +0 dB) ­3 Harmonic distortion 0.005% or less (at 1 kHz) Circuit system Input level adjustment range 0.3 ­ 6.0 V (RCA pin jacks) 1.2 ­ 12 V (High level input) High-pass filter 50 ­ 300 Hz, ­12 dB/oct Low-pass filter 50 ­ 300 Hz, ­12 dB/oct Low boost 0 ­ 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 ­ 16 V Current drain at rated output: 31 A (4 ) Remote input: 1 mA Dimensions Approx. 403 Ч 55 Ч 277 mm (w/h/d) (15 7/8 Ч 2 1/4 Ч 11 in) not incl. projecting parts and controls Mass Approx. 4.7 kg (10 lb. 6 oz.) not incl. accessories Supplied accessories Mounting screws (4) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. STEREO POWER AMPLIFIER 9-879-366-01 2004L04-1 © 2004. 12 Sony Corporation e Vehicle Company Published by Sony Engineering Corporation 1 XM-SD46X Notes on Chip Component Replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with