Clarion CD037RMP vers.2 free download

File name CD037RMP vers.2.pdf

Xiamen Clarion Electrical Enterprise Co., Ltd 8/F., Xiamen Mail Processing Centre, No.275 Lujiang Road, Xiamen, China Tel:+86-592-2389080 Fax:+86-592-2389089 Published by Service Dept. 298-6400-37-02 (GEN. 2009) Printed in P.R.C. Clarion Co., Ltd. 50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Manual CD/USB/MP3 Receiver Model CD037RMP ORIGINAL SERVICE MANUAL This additional service manual is designed to be used together with Original Model CD037RMP DIFFERENCE EXPLODE VIEW .PART LIST Switch DCP Section/Main Section (Refer to page 10 of the original service manual) NO. 29 PARTS NO. SERVOCD037V2 DESCRIPTION SERVO PCB Q'TY 1 Original Model CD037RMP Manual No. 298-6400-37-00 DIFFERENCE FROM ORIGINAL MODEL 1. EXPLANATION OF IC 2. PART LIST Switch DCP Section Main Section 3. ELETRICAL PARTS LIST Main PWB Section 4. PRINTED WIRING BOARD Section CD MECHANISM 5. PRINTED WIRING BOARD Main PWB section 6. CIRCUIT DIAGRAM Section CD MECHANISM 7. CIRCUIT DIAGRAM Main PWB Section DIFFERENCE ELETRICAL PARTS LIST Main PWB Section (Refer page 11 to 14 of the original service manual) REF. No. IC201 LED202 CON1 CON1 PART. No. 0010RF881703100 017WWOR150TSC00 377R140125B0000 37814125120MU00 Description MCU RF8817-031 LED Red FPC/FFC Connector 14 FFC 14 pin NOTE * Specifications and design are subject to change without notice for further improvement. -1- CD037RMP EXPLANATION IC PIN FUNCTION DOCUMENT No: RF8817-0x1 PIN 1 P-NAME BT_OUT DIO IN4 2 IPOD_O DIO IN3 3 4 5 6 DIOO3 DIOO2 DIOO1 RESET I/O O I O I O O O HD H H H L H Act H DESCRIPTION Bluetooth Audio Control Output. Option diode input 4. iPod Audio Control output. Option diode input 3. Optional diode output 3 Optional diode output 2 Optional diode output 1 To start u-COM, High input should be triggered with high input. 3.2V reset is recommendable. 7 3 COLOR /DIO IN2 8 2 COLOR /ALARM O H 1. 3 COLOR output for front illumination. 2. Option diode input 2. 1. When front opened, the output is generated per 1sec. with 10% duty (LOW=LED on). With this port, a flashing LED is used. 2. When power is on, by pressing the {DISP} key for more than 1sec. the output is toggled. With this port, the switching of 2 color lamps can be used. /DIO IN1 9 FLMD0 HD H 3. Option diode input 1. This is a pin for setting flash memory programming mode. Connect FLMD0 to GND in the normal operation mode. In flash memory programming mode, connect this pin to the flash programmer. Series resister 4.7Kohm is needed to GND. 10 11 12 13 14 15 16 17 X-IN X-OUT REGC GND GND VDD VDD TOUCH_ DAT 18 TOUCH_ ALBEN I/O HD HD HD HD HD HD HD O 7.2 MHz X-TAL INPUT 7.2 MHz X-TAL OUTPUT Regulated Voltage output Ground. Ground. VDD 5V DC VDD 5V DC Data in/out from/to Touch Sensor(DT8800) Direct Connect with Pin50 Control output to DT8800. Direct Connect with Pin49 Open DRAIN Open DRAIN Open Refer to the circuit Open When not Used Open REMARK -2- CD037RMP PIN 19 P-NAME VR CLK I/O O Act DESCRIPTION E.VR Communication CLK OUT Needed pull up r