Samsung 632NW free download

File name 01_precautions_E.pdf

1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings 1. For continued safety, do not attempt to modify the circuit board. 2. Disconnect the AC power and DC power jack before servicing. 1-1-2. Servicing the LCD Monitor 1. When servicing the LCD Monitor, Disconnect the AC line cord from the AC outlet. 2. It is essential that service technicians have an accurate voltage meter available at all times. Check the calibration of this meter periodically. 1-1-3. Fire and Shock Hazard Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. 2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc. 3. Leakage Current Hot Check (Figure 1-1): WARNING : Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). (READING SHOULD) NOT BE ABOVE 0.5mA DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES LEAKAGE CURRENT TESTER 2-WIRE CORD *ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED) EARTH GROUND Figure 1-1. Leakage Current Test Circuit 4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test. 1-1-4. Product Safety Notices Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. 1-1 1. Precautions 1-2. Servicing Precautions WARNING: Caution: Note: An electrolytic capacitor installed with the wrong polarity might explode. Before servicing units covered by this service manual, read and follow the Safety Precautions sectio

File name 02_Product_specifications_E.pdf

2. Product specifications 2. Product specifications 2-1. Feature & Specifications Model Feature The multipurpose model not only has a small-sized Wide Panel and a simple design suitable for B2B requirements but also comes with a glowing look that will satisfy the B2C customer Boll Hinge Concept application (Package) Connectivity : Analog only Power Consumption : Max 34W DPMS : under 1 W (230Vac) Power : Internal Power with Inverter (5V - 2A,14V - 2.2A) - 90 ~ 264 Voltage Specifications Item LCD Panel Description TFT-LCD panel, RGB vertical stripe, normally white transmissive, 15.6-Inch Wide 0.258(H) mm x 0.258(V) mm pixel pitch Scanning Frequency Display Colors Maximum resolution Input Signal Input Sync Signal Maximum Pixel Clock rate Active Display Horizontal/Vertical Horizontal : 30 kHz ~ 61 kHz (Automatic) Vertical : 56 Hz ~ 75 Hz (SXGA : 60 Hz) 16.7 Million colors Horizontal: 1680 Pixels Vertical: 1050 Pixels Analog R,G,Bl Seperate H/V sync, Composite H/V, Sync-on-Green Level: TTL level 146 MHz 344.232(H) x 193.536(V) 632NW AC power voltage & Frequency AC 110V~130V, 60Hz & AC, 200V~240V 50Hz Power Consumption Dimensions Set (W x D x H) Weight (Set) Environmental Considerations 34 W (Max) 382 x 260 x 68 mm 2.5 kg Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Operating Humidity : 10% ~ 80% Storage temperature : -13°F ~ 113°F (-25°C ~ 45°C) Storage Humidity : 5% ~ 95% Note: Designs and specifications are subject to change without prior notice. 2-1 2. Product specifications 2-2. Spec Comparison to the Old Models Model Pebble (632NW) Pebble (206BW/226BW) Design Resolution Input Response Time Viewing Angle Brightness Contrast Dynamic Contrast MagicBright Feature 1360x768@60Hz D-Sub 8ms (w to b) 90/45 (CR>10) 250cd/mІ 1000:1 2000:1(Typ.) 7 step Magic Color Magic Bright3 Magic Tune (Premium) 1680 x 1050 D-Sub 2ms(G to G) 160/160(CR=10) 300cd/mІ 700:1 700:1 6 step Magic Color Magic Bright3 Magic Tune(Premium) 2-2 2. Product specifications 2-3. Accessories Product Description Quick Setup Guide Ccde. No BH68-00376L Remark Warranty Card (Not available in all locations) BH68-00633A Samsung Electronics Service center User's Guide, Monitor Driver D-Sub(15 Pin) Cable (Shipped as assembled with the set) Power Cord BN59-00585T BN39-00244B 3903-000085 2-3 2. Product specifications Memo 2-4

File name 04_trobleshooting_E.pdf

4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting 1. Before troubleshooting, setup the PC `s display as below. · Resolution: 1360 x 768 · H-frequency: 65 kHz · V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. · No raster appears: Function PBA, Main PBA, I/P PBA · 5V develop but no screen: Main PBA · 5V does not develop: I/P PBA 4. If you select Brightness adjust menu and push the " returns to factory reset. (Enter/Source)" button for 5 seconds, the monitor automatically 4-1 4. Troubleshooting 4-2. No Power Symptom - When turning on the Power button after connecting the power, the LED at the front of the monitor does not operate. - Check the IP board power fuse and the IP board output power. Major checkpoints - Check the connections for the IP board and the Main board inside the monitor. - Check the Main board power part and check also whether there is any abnormal output at other output terminals. CN600 IC602 IC601 Main Board Front Yes Check function assy. Diagnostics When Pin 4 of CN600 is 0V, Does proper DC 14V appear at pin 5 of CN600? Yes When pin 1 of IC 601 is DC 5V, Proper DC 3.3V appear at pin 3 of IC 601 Yes When pin 3 of IC 602 is DC 5V, Proper DC 1.8V appear at pin 2 of IC 602 Caution No Replace IP board. No Check IC 601 and related circuit. No Check IC 602 and related circuit. Make sure to disconnect the power before working on the IP board. 4-2 4. Troubleshooting 4-3. No Video (Analog) Symptom Major checkpoints -Though the LED power turns on, the screen is blank when connecting the VGA cable. - Check the D-sub cable connections. - Check whether the LVDS cable is connected correctly to the panel. - Check whether the lamp connector of the panel is connected correctly to the IP board. CN400 X201 IC200 R111,R114,R118 Main Board Front Check signal cable connection and power. Yes Diagnostics X1 oscillate proprely? Yes Is there R,G,B input at R111,R114 and R118? Yes Is there Hsync, Vsync waveform at Pin 32,33 of IC200? Yes Does the output signal appear at Pin 17~20, 22~27 of CN400? Yes There are DC 5V at Pin 1, 2 and 3 of CN400? Yes Replace LCD Panel. Caution Make sure to disconnect the power before working on the IP board. No Check PANEL_EN SIGNAL at R223 is High(On:High) and BL_EN signal at R601(ON: Low) is Low No Check CN400 and related circuit. No Check IC200 and related circuit. No Check input part. No Replace or check related circuit. 4-3 4. Troubleshooting 4-3-1. Circuit diagrams and waveforms (Analog) when no screen is displayed on the monitor 4-4 4. Troubleshooting 4-4. Faults and Corrective Actions Fault Photo Symptoms and Corrective Actions Symptoms: DVI signals are not recognized. Causes: This fault occurs when the PC does not recognize the mode information because the DVI DDC has not been input to the monitor. Remarks * Refer to the Training Manual for information on inputting the DVI DDC. Corrective Ac

File name 05_Exploded_View_and_Part_List_LS16PENSF_XBM(Ver2.0).pdf

5. Exploded View and Parts List 5. Exploded View and Parts List 5-1. LS16PENSF/XBM Expl oded View (632NW) T0003 M0215 M0006 T0514 M0013 M0028 M0027 5-1 5. Exploded View and Parts List 5-1-1. LS16PENSF/XBM Parts List (632NW) Location T0003 M0215 M0006 T0514 M0013 M0028 M0027 Code.No BN96-06436A BN07-00490A BN96-06437A BN61-02784A BN96-06438A BN96-04150D BN96-06439B Item & Specification ASSY COVER P-FRONT;LS15PE(632NW),,,ABS,H LCD-PANEL;M156B1-L01 ASSY SHIELD P-COVER;LS15PE,SECC T0.8 BRACKET-SUPPORT;PEBBLE,SPTE,0.3 ASSY COVER P-REAR;LS15PE(632NW),,,ABS,HB ASSY STAND P-BAR;-,PEBBLE17,-,ABS HB,BK2 ASSY STAND P-BASE;LS15PE,ABS HB,BK26 Q'ty 1 1 1 1 1 1 1 SA/SNA S.A S.A S.N.A S.N.A S.A S.A S.A Remark 5-2 5. Exploded View and Parts List 5-2. LS16PENSF/XBM Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location Code.No LS16PENSF/XBM 0.1 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...4 ...5 ...5 ...5 ...6 ...6 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...7 ...4 ...5 ...5 ...5 ...5 0.1 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 0.1 ..2 M0006 T0102 M0107 M0215 M0001 T0003 CCM1 M0112 T0022 T0023 M0130 M0145 M0014 M2893 M2893 T0238 T0313 T0174 R5 R7 R6 R8 R1 R2 R3 R4 C1 C2 C3 PCB M0014 L0405 L0405 T0313 SUBPCB M0002 M0013 M0081 T0060 CCM1 M0014 BN90-01443A BN96-06436A BN63-02183D BN63-04101A BN64-00534B BN64-00597B BN67-00193A BN96-04363A BN94-01300M BN39-00774A BN39-00788A BN97-01597B 3404-000299 BN97-01589M 2007-000122 2007-000122 2007-000123 2007-000123 2007-001157 2007-001157 2007-001157 2007-001157 2203-000189 2203-000189 2203-000189 BN41-00793B BN94-01310C 0601-001896 0601-001896 3404-001207 BN41-00791A BN90-01444A BN96-06438A 6003-001003 BN61-02830A BN63-02183D BN63-02880B BN63-02883B BN63-04094A BN73-00132B BN91-01803R BN07-00490A Item & Specification 632NW,WVC1/S16P0-LPE,16,LCD-MO,ECUADOR ASSY COVER FRONT;LS16PE ASSY COVER P-FRONT;LS15PE(632NW),,,ABS,H COVER-SHEET;Rhcm,PE Vinyl,T0.05,680mm,20 COVER-FRONT;LS15.6PEW,ABS,-,-,-,HB,-,BK2 KNOB CONTROL;PEBBLE,ABS,HB,BK26 KNOB POWER;PEBBLE,black highglossy LENS LED;PEBBLE,ABS HB,CLR ASSY BOARD P-FUCNTION;Pebble,SJ06-01-023 ASSY PCB MAIN-SEDA,FUCHION PCB;PABBLE* LEAD CONNECTOR;Pebble,UL1061#28,UL/CSA,3 LEAD CONNECTOR;Pebble,UL1061#28,4PIN,300 ASSY AUTO;PEBBLE* SWITCH-TACT;12V,50mA,120gf,6x6x4.3mm,SPS ASSY SMD;PABBLE R-CHIP;1.2Kohm,5%,1/10W,TP,1608 R-CHIP;1.2Kohm,5%,1/10W,TP,1608 R-CHIP;1.5Kohm,5%,1/10W,TP,1608 R-CHIP;1.5Kohm,5%,1/10W,TP,1608 R-CHIP;750ohm,5%,1/10W,TP,1608 R-CHIP;750ohm,5%,1/10W,TP,1608 R-CHIP;750ohm,5%,1/10W,TP,1608 R-CHIP;750ohm,5%,1/10W,TP,1608 C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608 C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608 C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608 PCB SUB-FUNCTION;Pebble,FR-1,1,1.1,1.6,8 ASSY PCB MISC-SEDA,POWER,BN96-;PABBLE LED;SMD,BLUE,1.6x0.8x0.4mm,470,1.6x0.8x0 LED;SMD,BLUE,1.6x0.8x0.4mm,470,1.6x0.8x0 SWITCH-TACT;12V,50mA,160gf,6.2X6.2,SPST PCB SUB-POWER;Pebble,FR-1

File name 05_Exploded_View_and_Part_List_LS16PENSF_XBM.pdf

5. Exploded View and Parts List 5. Exploded View and Parts List 5-1. LS16PENSF/XBM Exploded View T0003 M0215 M0006 T0514 M0013 M0028 M0027 5-1 5. Exploded View and Parts List 5-1-1. LS16PENSF/XBM Parts List Location T0003 M0215 M0006 T0514 M0013 M0028 M0027 Code.No BN96-06436A BN07-00490A BN96-06437A BN61-02784A BN96-06438A BN96-04150D BN96-06439A Item & Specification ASSY COVER P-FRONT;LS15PE(632NW),,,ABS H LCD-PANEL;M156B1-L01 ASSY SHIELD P-COVER;LS15PE,SECC T0.8 BRACKET-SUPPORT;PEBBLE,SPTE,0.3 ASSY COVER P-REAR;LS15PE(632NW),,,ABS HB ASSY STAND P-BAR;-,PEBBLE17,-,ABS HB,BK2 ASSY STAND P-BASE;LS15PE,ABS HB,BK26 Q'ty 1 1 1 1 1 1 1 SA/SNA S.A S.A S.N.A S.N.A S.A S.A S.A Remark 5-2 5. Exploded View and Parts List 5-2. LS16PENSF/XBM Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location Code.No LS16PENSF/ XBM 0.1 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...4 ...4 0.1 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 0.1 ..2 0.1 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...4 ...4 ...4 ...4 ...4 ...4 ...4 ...4 ...4 M0006 T0102 M0107 M0215 M0017 M0081 M0081 M0081 M0174 T0514 M0014 CN101 CN330 T0174 SUB05 D108 D109 D110 D600 D603 ZD111 ZD112 ZD202 M0001 T0003 CCM1 M0112 T0022 T0023 M0130 M0145 M0014 M0014 M0002 M0013 M0081 T0060 CCM1 M0014 BN90-01443A BN96-06436A BN63-02183D BN63-04101A BN64-00534B BN64-00597B BN67-00193A BN96-04363A BN94-01300M BN94-01310C BN90-01444A BN96-06438A 6003-001003 BN61-02830A BN63-02183D BN63-02880B BN63-02883B BN63-04094A BN73-00132B BN91-01803R BN07-00490A BN91-01914L 6003-000282 6003-000282 6003-001439 BN44-00164C BN61-02784A BN94-01576T 3701-001219 3711-004712 BN97-01911R 0202-001477 0401-001056 0401-001056 0401-001056 0402-001614 0402-001614 0403-001411 0403-001411 0403-001411 Item & Specification 632NW,WVC1/S16P0-LPE,16,LCD-MO,ECUADOR Q'ty SA/SNA Remark ASSY COVER FRONT;LS16PE ASSY COVER P-FRONT;LS15PE(632NW),,,ABS H COVER-SHEET;Rhcm,PE Vinyl,T0.05,680mm,20 COVER-FRONT;LS15.6PEW,ABS,HB,BK26,H/GLOS KNOB CONTROL;PEBBLE,ABS,HB,BK26 KNOB POWER;PEBBLE,black highglossy LENS LED;PEBBLE,ABS HB,CLR ASSY BOARD P-FUCNTION;Pebble,SJ06-01-023 ASSY PCB MAIN-SEDA,FUCHION PCB;PABBLE* ASSY PCB MISC-SEDA,POWER,BN96-;PABBLE ASSY COVER REAR;LS16PE ASSY COVER P-REAR;LS15PE(632NW),,,ABS HB SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR SPRING ETC;PEBBLE,SK5,1.0,LS19PEB,HRC 45 COVER-SHEET;Rhcm,PE Vinyl,T0.05,680mm,20 COVER-STAND BAR;PEBBLE,ABS HB,T2.6,BK26, COVER-HINGE;PEBBLE,ABS HB,T2.6,BK26,HF-0 COVER-REAR;LS15.6PEW,ABS,HB,BK26,H/GLOSS RUBBER-CAP;PEBBLE,ELASTOMER,BK07,HB ASSY LCD-CTZ;LS16PEN* LCD-PANEL;M156B1-L01 ASSY CHASSIS-CTZ,W/W;LS16PEN* SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW SCREW-TAPTITE;BH,+,-,S,M4,L8,ZPC(WHT),SW IP BOARD;IP-16145A,PEBBLE 15.6",3.3~4.7m BRACKET-SUPPORT;PEBBLE,SPTE,0.3 ASSY PCB MAIN-CTZ,W/W;LS16PEN* CONNECTOR-DSUB;15P,3R,FEMALE,ANGLE,AUF HEADER-BOARD TO CABLE;BOX,9P,1R,2mm,STRA ASSY SMD;LS16PEN* SOLDER-CREAM;LST309-M,-,D20~45##,96.5Sn/ DIODE

File name 07_Schematic_Diagram_E(Ver2.0).pdf

7. Schematic Diagram 7. Schematic Diagram 7-1. Circuit Descriptions Location Scaler IC200 Flash Memory IC201 IC203 Regulator SE717M-LF SE717M- SCALER Function Besides the ADC, LVDS, and scaling part, an MCU is embedded as well. All of them are integrated into one chip. Stores the MCU program embedded in the scaler. It is of a flash type and rewritable. Stores the OSD and various timing values. An IC that receives DC voltage inputs. It is used in circuits that stabilize the DC voltage. Remark SE717M-LF MX25L1005MC 24C08 AP1084K18A AP1117D-33A 7-1 7. Schematic Diagram 7-2. Schematic Diagrams(Main Block Diagram) 7-3. Schematic Diagrams(Main Block Diagram) Panel LVDS signal Key input Crystal SE717M-LF (Scaler) Embeded MCU Function: Transmits the LVDS signals obtained by scaling the received analog or digital inputs to fit the panel resolution. Since the MCU Core is embedded, it performs the existing Micom function but uses external memory as it has no internal memory. MX25L1005MC (Flash Memory) Function: Saves the MCU code (Hex) data SDR I2C 24C08 (NVRAM) Function: Saves the timing value for each OSD and mode. Analog Signal Function Ass'y Function: Transmits the voltage value input when pressing a key. 7-2 7. Schematic Diagram 7-4. Schematic Diagrams(Panel Part) 7-3 7. Schematic Diagram 7-5. Schematic Diagrams(IP Board) SMPS Part 7-4 7. Schematic Diagram Inverter Part 7-5 7. Schematic Diagrams 7-6. Schematic Diagrams (Main PBA) This Document can not be used without Samsungs authorization. VIN VOUT ADJ 1 IN OUT OUT GND 3 2 7-7 7. Schematic Diagrams Memo 7-8

File name 07_Schematic_Diagram_E.pdf

7. Schematic Diagram 7. Schematic Diagram 7-1. Circuit Descriptions Location Scaler IC200 Flash Memory IC201 IC203 Regulator SE717M-LF SE717M- SCALER Function Besides the ADC, LVDS, and scaling part, an MCU is embedded as well. All of them are integrated into one chip. Stores the MCU program embedded in the scaler. It is of a flash type and rewritable. Stores the OSD and various timing values. An IC that receives DC voltage inputs. It is used in circuits that stabilize the DC voltage. Remark SE717M-LF MX25L1005MC 24C08 AP1084K18A AP1117D-33A 7-1 7. Schematic Diagram 7-2. Schematic Diagrams(Main Block Diagram) 7-3. Schematic Diagrams(Main Block Diagram) Panel LVDS signal Key input Crystal SE717M-LF (Scaler) Embeded MCU Function: Transmits the LVDS signals obtained by scaling the received analog or digital inputs to fit the panel resolution. Since the MCU Core is embedded, it performs the existing Micom function but uses external memory as it has no internal memory. MX25L1005MC (Flash Memory) Function: Saves the MCU code (Hex) data SDR I2C 24C08 (NVRAM) Function: Saves the timing value for each OSD and mode. Analog Signal Function Ass'y Function: Transmits the voltage value input when pressing a key. 7-2 7. Schematic Diagram 7-4. Schematic Diagrams(Panel Part) 7-3 7. Schematic Diagram 7-5. Schematic Diagrams(IP Board) SMPS Part 7-4 7. Schematic Diagram Inverter Part 7-5 7. Schematic Diagrams 7-6. Schematic Diagrams (Main PBA) This Document can not be used without Samsungs authorization. VIN VOUT ADJ 1 IN OUT OUT GND 3 2 7-7 7. Schematic Diagrams Memo 7-8

File name 0_Cover_E.pdf

LCD-Monitor Chassis Model :LS16PEN :632NW SERVICE TFT-LCD Monitor Manual Contens 1.Precautions 2. Product specifications 3.DisassemblyandReassemble 4.Troubleshooting 5.ExplodedView&PartList 6.WiringDiagram 7.SchematicDiagram 632NW Refer to the service manual in the GSPN (see the rear cover) for the more information. Contents 1.Precautions... 1-1 1-1. Safety Precautions ... 1-1 1-2. Servicing Precautions ... 1-2 1-3. Static Electricity Precautions ... 1-2 1-4. Installation Precautions ... 1-3 2. Product specifications... 2-1 2-1. Feature & Specifications ... 2-1 2-2. Spec Comparison to the Old Models ... 2-2 2-3. Accessories ... 2-3 3.DisassemblyandReassemble... 3-1 3-1. Disassembly ... 3-1 3-2. Assembly ... 3-4 3-3. Installing the Stand ... 3-5 4.Troubleshooting... 4-1 4-1. Troubleshooting ... 4-1 4-2. No Power ... 4-2 4-3. No Video (Analog) ... 4-3 4-4. Faults and Corrective Actions ... 4-5 4-5. Adjustment ... 4-6 5.ExplodedViewandPartsList... 5-1 5-1. Exploded View ...