icom icr2 free download

File name icr2_service.pdf

SERVICE MANUAL COMMUNICATIONS RECEIVER INTRODUCTION This service manual describes the latest service information for the IC-R2 at the time of publication. MODEL VERSION Europe Italy Taiwan U.S.A. Canada Other SYMBOL EUR ITA TPE USA CAN OTH OTH-1 IC-R2 To upgrade quality, all electrical or mechanical parts and internal circuits are subject to change without notice or obligation. DANGER NEVER connect the receiver to an AC outlet or to a DC power supply that uses more than 3.5 V. Such a connection could cause a fire hazard and/or electric. DO NOT expose the receiver to rain, snow or any liquids. DO NOT reverse the polarities of the power supply when connecting the receiver. DO NOT apply an RF signal of more than 20 dBm (100mW) to the antenna connector. This could damage the receiver's front end. ORDERING PARTS Be sure to include the following four points when ordering replacement parts: 1. 2. 3. 4. 10-digit order numbers Component part number and name Equipment model name and unit name Quantity required 8930046581 LCD Contact IC-R2 8810009560 Screw PH BO M2x6 ZK IC-R2 LOGIC UNIT 5 pieces Chassis 10 pieces Addresses are provided on the inside back cover for your convenience. REPAIR NOTES 1. 2. 3. 4. 5. 6. Make sure a problem is internal before disassembling the receiver. DO NOT open the receiver until the receiver is disconnected from its power source. DO NOT force any of the variable components. Turn them slowly and smoothly. DO NOT short any circuits or electronic parts. An insulated turning tool MUST be used for all adjustments. DO NOT keep power ON for a long time when the receiver is defective. READ the instructions of test equipment thoroughly before connecting equipment to the receiver. TABLE OF CONTENTS SECTION SECTION SECTION SECTION 1 2 3 4 4-1 4-2 4-3 4-4 SPECIFICATIONS INSIDE VIEWS DISASSEMBLY INSTRUCTIONS CIRCUIT DESCRIPTION RECEIVER CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 PLL CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 POWER SUPPLY CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 PORT ALLOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 SECTION 5 5-1 5-2 5-3 ADJUSTMENT PROCEDURES PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1 PLL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3 RECEIVER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5 SECTION SECTION SECTION SECTION 6 7 8 9 9-1 9-2 PARTS LIST MECHANICAL PARTS AND DISASSEMBLY SEMI-CONDUCTOR INFORMATION BOARD LAYOUTS LOGIC UNIT . . . . . . . . . . .