File information: | |
File name: | SAMSUNG chassis KS4.rar [preview KS4] |
Size: | 1563 kB |
Extension: | |
Mfg: | Samsung |
Model: | KS4 🔎 |
Original: | KS4 🔎 |
Descr: | SAMSUNG chassis KS4 |
Group: | Electronics > Consumer electronics > TV |
Uploaded: | 28-09-2004 |
User: | plamensl |
Multipart: | No multipart |
Information about the files in archive: | ||
Decompress result: | OK | |
Extracted files: | 2 | |
File name samsung_tv_ch_ks4.pdf iagrams TH EW) TP07 TP10 TP08 TP09 TP09 TP01 TP06 TP10 TP08 TP05 TP02 TP07 TP03 TP04 : Power Lin : Signal Lin TP12 TP13 TP15 TP14 TP22 TP23 TP23 TP22 TP24 TP18 TP25 TP21 TP20 TP24 TP25 TP32 TP33 TP35 TP26 TP33 TP34 TP27 TP32 TP35 TP34 TP31 TP29 TP28 TP30 : Power Line : Signal Line -EW) H | ||
File name samsung_tv_ch_ks4_adj.pdf Alignment and Adjustments 4. Alignment and Adjustments 4-1 General Alignment Instructions 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 4-2 Automatic Degaussing A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments. 4-3 High Voltage Check CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level). 1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 30 KV under any conditions. Samsung Electronics 4-1 Alignment and Adjustments 4-4 FOCUS Adjustment 1. Input a black and white signal. 2. Adjust the tuning control for the clearest picture. 3. Adjust the FOCUS control for well defined scanning lines in the center area of the screen. 4-5 SCREEN Adjustment 1. Input Toshiba Pattern 2. Enter "Service Mode".(Refer to "4-8-1 Service Mode") 3. Select "G2-Adjust". 4. Set the values as below. Table 1. Screen Adjustment Table COLR G B (Smallest Value) 100 100 100 100 150 65 65 65 120 150 Noraml CIS No 1 2 3 4 5 6 7 8 9 INCH / CRT 14" / SDI 15PF / SDI 21" 1.7R / SDI 21" 1.7R / |
Date | User | Rating | Comment |
27-02-2007 | chuelca | 10 | ok |
27-02-2007 | chuelca | 1 | yes |