Sony DSCS30 free download

File name dsc-s30.pdf

DSC-S30/S50 SERVICE MANUAL Level 1 Ver 1.3 2004. 07 AEP Model UK Model Photo: DSC-S30 SPECIFICATIONS System Image device 1/2.7 type color CCD Lens 3 Ч zoom lens f = 6.1 ­ 18.3 mm (39 ­ 117 mm when converted into a 35 mm still camera) F = 2.8 ­ 2.9 Exposure control Automatic exposure White balance Automatic, Indoor, Outdoor, Hold Data system Still: JPEG, GIF (in TEXT mode), TIFF Movie (DSC-S50 only): MPEG1 Audio with still image (DSC-S50 only): MPEG1 (Monaural) Recording medium "Memory Stick" Flash Recommended recording distance: 11 7/8 inches to 8 1/4 feet (0.3 m to 2.5 m) Output connector A/V OUT (Monaural) (DSC-S50 only) Minijack Video: 1 Vp-p, 75 ohms, unbalanced, sync negative Audio: 327 mV (at a 47 kilohm load) Output impedance: 2.2 kilohms VIDEO OUT (DSC-S30 only) Minijack Digital I/O (USB) Special minijack LCD screen Used LCD panel 2 type TFT (Thin Film Transistor active matrix) drive Total number of dots 123 200 (560 Ч220) dots Operation temperature 32°F to 104°F (0°C to 40°C) Storage temperature ­4°F to +140°F (­20°C to +60°C) Maximum dimensions 4 1/2 Ч2 3/4 Ч2 3/4 inches (113 Ч68 Ч69 mm) (w/h/d) Mass Approx. 13 oz (370 g) (including battery pack NPFM50, "Memory Stick", wrist strap and lens cap etc.) Built-in microphone (DSC-S50 only) Electret condenser microphone Built-in speaker (DSC-S50 only) Dynamic speaker Storage temperature ­4°F to +140°F (­20°C to +60°C) Maximum dimensions 5Ч 1 9/16 Ч2 1/2 inches (125 Ч39 Ч62 mm) (w/h/d) Mass Approx. 10 oz (280 g) NP-FM50 battery pack Used battery Lithium ion battery Maximum voltage DC 8.4 V Nominal voltage DC 7.2 V Capacity 8.5 Wh (1 180mAh) Design and specifications are subject to change without notice. General Used battery pack NP-FM50 Power requirements 8.4 V Power consumption (during recording) 2.9 W AC-L10 AC power adaptor Power requirements 100 to 240 V AC, 50/60 Hz Rated output voltage DC 8.4 V, 1.5 A in operating mode Operation temperature 32°F to 104°F (0°C to 40°C) DIGITAL STILL CAMERA SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their