| Subject | Text |
| You can try to put a 400 Volts rated capacitor across the 230 Volts motor terminals. (50 to 80 µF.) |
| Re: Tektronix 422 | [quote:da0218760b="ninelives"]I have a Tektronix TM 515 mainframe with the following plug-ins. Due |
|
|
| IT is not convergency if you mess with that god help you then you need a generator to get it right o |
| [quote:21853667a5="vtech"]Without being able to see more of the equipment, it would have to be a gu |
| philips monitor brilliance 150p | I got a philips LCD monitor brilliance 150p.
I hooked a pattern generator to it.On the right side I |
| [quote:6bf443bc09="Anonymous"]OOPS... p/n I replaced is [b:6bf443bc09]23786221[/b:6bf443bc09]
Phi |
| Need suggestions of multitest units like the elenco mx-9300B | Incase no one knows what this unit is, http://www.esssales.com/elenco/all-in-one.html
I need a te |
| DELL lcd E151FPb monitor. | Monitor comes on (pwr led always green); with following on screen:
"Monitor in SLEEP mode; Pre |
| Thank you jts1957 but no, this will not cure the overheat problem.
I tried several LA7845N, sever |
| Well, yeah, you are messing with relatively high power equipment and can get into embarrassing situa |
| Tektronix TM 515 w/ PS 501-2, SC 501, FG 501, DM 501, DC 504 | I have a Tektronix TM 515 mainframe with the following plug-ins. Due to its portability this unit i |
| Philips PM 5138 Service Manual | Jetzt probier ich es nochmal auf Deutsch.
Hallo,
ich habe hier vor mir einen Philips PM 5138 Fun |
| GW or Elenco or insteak GFG-8016G schematic | Hello. Please i need a schematic for the GW or Elenco or insteak GFG-8016G function generator. My ge |
| 14PT1532 /94S ctv went off suddenly on service table | this chassis uses
MC44603 AP powersupply
TDA 7056B audio
TDA 8841 S1 signal processor v h |
| Horiz output | Ahh I get it now,
I would like to scope the base signal while lamp load is on and measure frequency |
| Sell Instruments | Miko-Kings Instruments Ltd http://www.miko.com.hk
Miko-Kings Instruments Ltd., hereinafter called |
| Try supplying a 1 kHz sine signal from a tone generator to an AUX input and look at the output signa |
|
|
| Re: [email protected] | [quote:e0b3a37a3c="robtv"]Thanks for the input,
I was wondering if y |
| DC Motor C4557-60003 from HP deskjet printer | I tested this motor,
it starts turning at 1V, very slowly. I was quite surprised by this.
At 6V it |
| In order to measure the output of an amp, you would need test equipment;
Load resistors, scope |
| [quote:3abd774048="awright"]Well, yeah, you are messing with relatively high power equipment and can |
| wavetek 91 service info or diagram needed | I need a service manual or diagram for a wavetek 91 20MHZ function generator. Pleae e-mail wa6ipz2@j |
| Remember;
When talking about "impedance", it is actually the resistance of the speaker |
| Can anyone help identify... | Hello,
I apologize in advance for the poor pic as it came from a small pic in a magazine scan but |
| Compaq Monitor V700, schematic diagram | Hello,
I work at GM Antwerp, Belgium, and we have 9 defective V700 compaq monitors, all with the |
| I found out what it is | Ok the first guy whom was paid to come out and look at is was 100% wrong I finally got a place from |
| Zenith ZB4683RK convergence problem | Hello, If you look at the pics at
http://webpages.charter.net/jenglish_tnx/
you will see what I s |
| Need a JVC rear projection tv Expert | I have a JVC AV-56WP74 Build date 2003.
Ok I know that I need To replace the two STK392-110 IC's. |
| What type of signal should I be seeing on the flyback generator (pin 11) located on vertical deflect |
| manual | You should be able to get the manual from Panasonic Literature division. They should still have the |