Subject | Text |
| The DCU/convergence generator stores the information. If 480 is good and 1080 is bad, I would suspec |
Ps2 Repair | Hi Friends
Im new to the forum and hope that i am posting in the right place.
A friend of mine h |
|
Problem with Bose 321 System | I have as Bose 321 system on the bench that has the following issue:
1) After extended use the audi |
| As far as I know when it comes to computer motherboards there are no "board specific" test |
14PT1532 /94S ctv went off suddenly on service table | this chassis uses
MC44603 AP powersupply
TDA 7056B audio
TDA 8841 S1 signal processor v h |
Need a JVC rear projection tv Expert | I have a JVC AV-56WP74 Build date 2003.
Ok I know that I need To replace the two STK392-110 IC's. |
| [quote:bdba5ca32f="vtech"]Remember;
When talking about "impedance", it is actually the |
| It is demagnetize --not demagnify. Any TV servicer with a degauser coil can do that. In general ever |
Selling Benchtop NTSC Generator in excellent condition. | Selling a TENMA Benchtop NTSC Generator in Mint condition.
Features: 16 video patterns
# Interlac |
Need suggestions of multitest units like the elenco mx-9300B | Incase no one knows what this unit is, http://www.esssales.com/elenco/all-in-one.html
I need a te |
| Well, yeah, you are messing with relatively high power equipment and can get into embarrassing situa |
Re: samsung projection tv | [quote:2ff0abc0c9="garster59"]how do I enter the service mode in the tv with the remote[/quote:2ff0a |
| Well'p, got it to stop eating fuses, and everything's plugged in. Replaced a few parts and it seems |
Digital Alarm Clock Issue | I have a digital alarm clock that has a large LCD display. A while back some of the sections of the |
| Thank you jts1957 but no, this will not cure the overheat problem.
I tried several LA7845N, sever |
GW or Elenco or insteak GFG-8016G schematic | Hello. Please i need a schematic for the GW or Elenco or insteak GFG-8016G function generator. My ge |
| Hi this is a Sony D99 chassis and the flashing of the Amber LED indicates the fault area.
D99 LED F |
|
philips 900 series fr931 | vcr light keeps coming on and then going off with no pattern and sometimes only half lights up front |
| Hi minnie,
I got the convergence IC's and I installed them. I neglected to check the 1 Ohm resistor |
| Remember;
When talking about "impedance", it is actually the resistance of the speaker |
Jvc Model Av-27850, Chassis A59 keystone raster | Working on JVC tv model AV-27850 Chassis A59. Raster has keystone pattern , i checked the yoke with |
| there is no real default, the adjustments are there to correct the geometry settings for each set, i |
wavetek 91 service info or diagram needed | I need a service manual or diagram for a wavetek 91 20MHZ function generator. Pleae e-mail wa6ipz2@j |
display divided | Looks like display is divided in two.From center to left side bars from my
generator show correct,f |
Hitachi 50UX53K PTV, intermittent crosshatch | Hi,
This set is blinking between normal picture and a crosshatch pattern. Deflection/Power board |
| If the set detects a problem, the front LED will blink a number of times, pause and blink again. Co |
| http://techno-fix.com/service_manual/Product%20Manual%20KingCraft%20#6915 Generator.rar
here u ar |
DC Motor C4557-60003 from HP deskjet printer | I tested this motor,
it starts turning at 1V, very slowly. I was quite surprised by this.
At 6V it |
Siemens FG D2011-8AA Schematic / Service manual | Looking for Siemens function generator D2011-8AA Schematic / Service manual
Looks close to Toellner |
Hitachi C32WD2 | Hitachi 32 inch wide screen, heavy pinstripe pattern over picture, can anyone help. |