Subject | Text |
Dead Black Diamond BD28WS | Hello to everyone this is my first post here. I have a BD28WS Black Diamond TV. The fault is when I |
compaq monitor S910 | hello,
it could very well be a capacitor in the power supply, so you have to look in the neighbourh |
|
Re: resistor | [quote:08044d4b4b="dmattingly1"]I need to know what resistor to use to replace a .6 -.7vlt. surface |
| This is what I know.
# Continuous Blinking: Not getting reply from IC301 Jungle IC, Bad "IK" video |
Any experience with BAPCO IEC601L Universal? | Using a BAPCO IEC601L Universal Safety Tester for Leakage Current tests. Recently back from Calibrat |
| Basically boils down to your circuit application but can be confusing looking through various calcul |
Bosch Mercedes Benz code needs | Bosch
7 620 000 009
815CM0009 B 0570958
Mercedes benz
034953 MB Truck Base Low
A 000 446 36 62 |
Toshiba CX35d80, No sound | The Sound was very low at full volumn. Now there is no sound. Can I buy & replace a sound board? |
| The 'K' as part of the resistor specification represents tolerance. I think from memory it is +-10% |
stereo fuses | This does not mean you have a bigger problem.
The "F" stands for fast blow and the "T" for time-del |
Re: Fuse size | [quote:082baba358="vivo"]I currently have a 4 channel amp powering my speakers in my car. I am plann |
MITSUBIBHI SHUTDOWN | HELLO. Well KIKI the first thing that comes to mind is even though the tubes were replaced there had |
| Hmmm. This could be a pain in the arse, but maybe not. It is possible that there is a missing low vo |
measuring high value resistor? | i have a 1.8 Mega Ohm resitor, my meter can read up to 2 mega ohm, but when i try and read the value |
| How is the set stuck in standby? Are there any sounds coming from the back of the TV when you switch |
| [quote:1c07ba0a39="Anonymous"]Hi Mozster,
I have a Hinari Lifestlye Microwave and also MANUAL!!!! |
| Please make sure the vertical signal is sending out from Matrox Millenium by oscilloscope or counter |
|
| Jason,
When you say you disconnected the U board, did you get any raster?
I wonder why you wou |
| dont forget to change low ohm resistor off flybackthat feeds the voltage usually 26volts to the vert |
| Thank you vtech for a thoughtful, if discouraging reply.
I screwed down the player unit and attac |
| Just measure the voltage and current
RMS power = RMS V X RMS I
or just P=V X I
Peak = 1. |
| What is the maximum output current requirement when the "arc" is taking place? That would give anyo |
| [quote:b18826c1bb="plamensl"]Hi,
The situation is very much the same here (in Bulgaria) - same ne |
| Thanks for the link.
I need a schematic model that contains PWM like KA7500, TL 494, specially &q |
| When using solar energy for heating of water, it is very inefficient to use photovoltaic cells and e |
MDX-M690 | Dont know if this helps, im sure you've probably sorted it out by now.
Looking at the PDF, the Am |
| I don't really know that much about cars in general, but it sounds similar to a problem I've had wit |
| if the 3a fuse went and you replaced it with a 3.15a fuse and that went the fault is not the fuse. t |
DELL M992 CRT monitor | Looking for a DELL M992 service manual..
Fault seems to be low B+ from the power supply. Maybe it |
Mitac 8640 power problem | Hi
I have this mitac 8640sc notebook(labelled Medion), that the user apparently have dropped a sc |