| Subject | Text |
| Hi there,
great care must be taken by replacing laserunits. Mostly, and i mean
almost always, a |
| Hi,
The situation is very much the same here (in Bulgaria) - same new stores, which give credit, |
|
|
| Re: Do this test | Forgot to mention: Keep CD player's volume quite low to keep from exceeding input level rating of yo |
| Re: I want to get code please | [quote:80d9f13b39="abrwd8"]MERCEDES-BENZ
BOSCH
7 620 000 009
815 CM0009 B 6793176
034953 MB RUCK |
| try to resolder terminals at the power supply section esp. high current devices. |
| Hi to you all newbee on forum would like some help please | Depends on the use but I would use a pulse width type like the one in the link below as the D.C moto |
| [quote:fb10162a27="LJ"]If that so, check the voltage between Collector to emitter voltage, from data |
| Service manual and troubleshooting flash codes SONY TV | Looking for info on troubleshooting flash codes for Sony TV Mod. KV-35-V65. Set has no picture or so |
| Autoradio | I need code for this radio..
Can someone help me with this radio ? Please.
Here the serial n |
| Yep!
First check if there is a short between the collector and emitter.
(The "short" (low resi |
| Varying degrees of electronic knowledge | I've Noticed That Users of the site have varying degrees of electronic knowledge it would be helpful |
| AC to DC to conserve energy, good idea or bad? | current=watts/volts.
The lower the voltage the higher the current.
120v better as a result. |
| If it's a very simple supply with the three voltages you mention and ONLY has a power supply turn-on |
| Aiwa Amplifier MX-Z4400MK | Hi - Can anyone help with schematic for this amplifier. It has very low output. I notice that one ch |
| Your dead TX100 chassis Tv | As well as the good advice given by last poster, check/replace the Polyester/Mylar Capacitors across |
| Re: BLAUPUNKT CODE | [quote:3059d79f62="DELIJA"]hi,i need a code for blaupunkt made in portugal BP937215339337 fiat pun |
| Philips Brilliance 181AS LCD TFT monitor with dull display | Hi everyone,
Perhaps someone would be kind enough to offer me some advice... I repair electronic |
|
|
| where to finda hp7806 isolation amp ?? | I have a board from a Mitsubishi CNC mill its a MDS-A-SVJ-03 servo control unit. It is giving a cu |
| STA353 | ok here or read the pdf icmaster.com
have fun
STA353
PNP Silicon Transistor
Descript |
| Bush ws6671sil - 11AK19Pro chassis - Help needed! | Hello!
First off, this site is probably the most useful electronic repair site I have come across. |
| Re: please need code | [quote:8ea1ad7c3e="ssjdhsn"]Mercedes-Benz
BLAUPUNKT
Made in Portugal
7 620 000 020
815 BP002 |
| NiMh charger | Hello,
I assume that you don't have the intension to load your cells at "quick rate", so let's sa |
| Can you substitute with an external power source as "test"?
Just make sure ratings are |
| I have the same problem with my Philips 28pw8504.When i switch the set on, after 3 min (sometimes mo |
| Re: please need code | [quote:7a20b76521="qquaid"]Mercedes-Benz
BLAUPUNKT
Made in Portugal
7 620 000 020
815 BP0020 |
| 5V to 3.3V micropower voltage regulator | hello,
For a microcontroller programmer using USB port ineeded to convert 5v to 3.3V,initially one |
| Something to think about.
What is your life worth?
Rewiring an electric heater to save energy |
| Re: please need code | [quote:113e83421b="qquaid"]Mercedes-Benz
BLAUPUNKT
Made in Portugal
7 620 000 020
815 BP0020 |
| its a board level repair. basically you need to take it to a daewoo servicer.
you can figure out |
| updates! TV made a pop noise then it shuts off. wait few minutes and will turn on again. ( TV only g |