Text preview for : SJ-MR2301.pdf part of Panasonic SJ-MR2301 SJ-MR2301
PORTABLE MINIDISC RECORDER -
Service Manual
Back to : SJ-MR2301.rar | Home
ORDER No.AD0211148C3
Portable MD Recorder
SJ-MR230DGH / SJ-MR230DGK
Colours (S)...................Silver Type (R)...................Red Type [(GK) area only.] (A)...................Blue Type
SPECIFICATIONS
Specifications
Audio System: Laser: Sampling frequency: Coding: No. of channels: Frequency response: Wow and flutter: General Input terminal OPT/LINE IN jack Impedance: Input level: MIC jack Impedance: Input level: Output terminal Head phone Jack: Speakers (Cradle): Speakers impedance: Power supply Rechargeable battery: DC 1.2V (included rechargeable battery) Battery: AC adaptor: Dimensions (WxHxD) Cabinet dimensions: incl.projecting parts: Weight: 78.2x71.6x17.9 mm 80.4x74.1x17.9 mm 121 g (with battery) 94 g (without battery) Play time (When used in hold mode, at 25°C, on a flat, stable surface) Battery type: Rechargeable Normal: LP2: LP4: Panasonic alkaline Normal: LP2: About 42 hours About 59 hours About 8 hours About 13 hours About 27 hours About 35 hours About 42 hours About 13 hours About 18 hours About 23 hours Play time Record time DC 1.5V (One LR6, AA, UM-3 battery) DC 4.5V (included AC adaptor) 8 3.0 mW+3.0 mW, 32 0.9 mW+0.9 mW, 8 600 SENS H: 0.4mV SENS L: 2.5mV 22k SENS H: 178mV SENS L: 500mV MiniDisc digital audio system Semiconductor laser (=780 nm) 44.1 kHz Adaptive Transform Acoustic Coding (ATRAC / ATRAC3) 2 (left and right, stereo) 1 (monaural, play only) 20 Hz-20 kHz (+0 dB, -8dB) Below measurable limit
LP4: Both together Normal LP2: LP4:
About 70 hours About 77 hours About 100 hours About 117 hours
About 21 hours About 35 hours About 50 hours About 62 hours
Notes:
- The play time may be less depending on the operating conditions. - Specifications are subject to charge without notice. Weight and dimensions are approximate.
2002 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
1. Accessories
- Rechargeable battery ass'y....................................1pc. (RFKFFAZ01EM1) - Rechargeable batt. case.........................................1pc. (RFA0475-Q) - External battery case..............................................1pc. (RFA1537-S2) - Carrying case.........................................................1pc. (RFC0069-H) - Stereo earphones...................................................1pc. (L0BAB0000174) - Connection cable...................................................1pc. (K2KA39B00001) - Clip type headphones............................................1pc. (L0BAE0000026) - Optical fiber cable..................................................1pc. (K7CXJCA00004) - Wired remote control..............................................1pc.
(N2QCBD000012)
For GH area
- Speaker ass'y.........................................................2pcs. (RFKAJMR250-S) - Cradle.....................................................................1pc. (RFE0114A) - AC adaptor.............................................................1pc. (RFEA413H-W)
For GK area
- Speaker ass'y.........................................................2pcs. (RFKAMR230GKS) - Cradle.....................................................................1pc. (RFE0114B) - AC adaptor..............................................................1pc. (RFEA413T-1W)
2. Precation of Laser Diode
3. Operating Instructions 4. Handling Precautions for Optical Magnetism Head Unit
The laser diode in the optical magnetism head unit may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the optical magnetism head unit.
4.1. Handling the optical magnetism head unit 1. The optical magnetism head unit is an extremely high-precision construction and must not be subjected to impact, excessive vibration, or other types of rough handling. 2. In order to prevent static electricity damage to the laser diode, use a short pin or similar tool to short the optical pickup's flexible circuit boards after they have been disconnected from the main circuit board. (as shown in Fig. 1 ) 3. Handle the flexible circuit boards with care; excessive force could cause them to be broken. 4. Do not turn the pre-set variable resistor (for adjustment of the laser power); it has been adjusted at the factory. (as shown in Fig. 2 )
Fig. 1
Fig. 2
4.2. Grounding for electrostatic breakdown prevention 1. Human body grounding Use the anti-static wrist strap to discharge the static electricity from your body. (as shown in Fig. 3 ) 2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the optical magnetism head unit is placed, and ground the sheet. (as shown in Fig. 4 )
Caution
The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the optical magnetism head unit.
Fig. 3
Fig. 4
5. Operation Checks and Component Replacement Procedures
- This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. - For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. - After replacing the main components (optical pickup or traverse motor, etc.) of mechanism unit block, change to the adjust mode, and then perform the " ROM/RAM auto-adjustment". 5.1. Checking for the main P.C.B.
- Check the main P.C.B. (A side) as shown below.
5.2. Replacement for the intermediate cabinet - Follow the (Step1)-(Step3) of item 5.1.
5.3. Replacement for the open knob - Follow the (Step1)-(Step3) of item 5.1. - Follow the (Step1)-(Step4) of item 5.2.
5.4. Replacement for the traverse motor - Follow the (Step1)-(Step3) of item 5.1.
5.5. Replacement for the LCD - Follow the (Step1)-(Step3) of item 5.1. - Follow the (Step1)-(Step4) of item 5.2.
5.6. Replacement for the lift motor - Follow the (Step1)-(Step3) of item 5.1. - Follow the (Step1)-(Step4) of item 5.2. - Follow the (Step1) of item 5.5.
5.7. Replacement for the optical pickup - Follow the (Step1)-(Step3) of item 5.1. - Follow the (Step1)-(Step4) of item 5.2. - Follow the (Step1)-(Step5) of item 5.4. - Follow the (Step1) of item 5.5.
6. Measurements and Adjsutments
Note: After replacing the main components (optical pickup or traverse motor, etc.) of mechanism unit block, change to the adjust mode, and then perform the "laser power adjustment", "off-set autoadjustment" and "playback-onlydisc/magneto-optical disc auto-adjustment".
6.1. Instruments to prepare 1. Playback-only disc (Test disc RFKV0006) 2. Commercially available recordable disc (fully recorded with music) (magneto-optical disc) 3. Laser power meter (LE8010 or compatible meter) 4. Remote controller (part No. N2QCBD000012 or N2QCBD000002, is attached to SJ-MJ75 (SJ-MJ75 is GH area only.))
Note: For use of MD cartridge type laser power meter, remove the intermediate cabinet before perform the laser power adjustment (as for the method of disassembly, refer to "5. Operation checks and main component replacement procedures".).
6.2. Laser power adjustment, Off-set automatic adjustment and Playback-only disc/magneto-optical disc auto- adjustment
6.2.1. Enter the adjustment mode
1. Set the battery and connect the remote controller. 2. Turn off the power, and switch main unit's HOLD switch off. 3. Press the buttons of the remote controller in order from 1 to 4 (as shown in Fig. 5 ).
Fig. 5
4. When the adjustment mode is activated, "T0E**" will be displayed on the LCD of remote controller and unit. After "T0E**" is displayed, select the desired adjustment itemwith the button or button of the remote controller. (If it is not displayed, perform the procedures written above again.)
*In the display of T0E** ~ TFE** shown above, you must adjust T0E**, T1E**, T2E** and T3E**. You must perform the adjustment byobserving the order T0E** T1E** T2E** T3E**.
6.2.2. Laser Power Adjustment
Adjust each laser power: read power for reading (play) and write power for writing (record). 6.2.2.1. Set the Unit to the Adjustment Mode Cautions
About handling the optical pickup and the magnetic head. - The optical pickup and the magnetic head are structured precisely; therefore, they are very fragile. Be careful not to touch them with the edge of the laser power meter. Do not touch the lens. - The sensor of the laser power meter is a very fine part. Be careful not to touch it to the optical pickup lens. - Do not loosen or remove the magnetic head installing screw. - The focus point of the laser reaches to 356°F. Therefore, avoid adjusting using laser power for a long time because the sensor of the laser power meter may be burned. - Do not allow the write power to even momentarily reach or exceed 6mW. Doing so will result in damage to the optical pickup. - Do not set the unit to the laser power adjustment mode with the MD loaded. Doing so may result in damage to the MD. - Laser diode in the optical pickup may be destroyed by the staticelectricity generated in your clothes or body. Be especially careful with the static electricity.
6.2.2.2. Adjustment Procedure
1. Have "T0E** " indicated on display, and move the optical pickup to the most inside (only when a MD cartridge type laser power meter is used). 2. Set the laser power meter. [For use of stick type laser power meter.] 2-1 Uncover the laser power meter. (as shown in Fig. 6 ) 2-2 Locate the sensor of the laser power meter right over above the optical pickup (horizontally at a level of the disc position). (as shown in Fig. 7 ) [For use of MD cartridge type laser power meter.] 2-1 Set the laser power meter and close the disc cover, fix it with tape as not to open. (as shown in Fig. 8 )
Fig. 6
Fig. 7
Fig. 8
3. Press the PLAY key of the remote controller ("T0E** " changes to "LD " of the LCD). 4. Press the key of the remote controller ("LD " changes to "LP " of the LCD).
5. Perform the read power adjustment. Set the light power at 600 W ±10% by using VOL+, VOL- , EQ and PLAY MODE keys of the remote controller. In the laser power adjustment, EQ and PLAY MODE keys change every8 steps for VOL+ and VOL- keys change 1 step.
Caution:
Proceeding on to the subsequent adjustment procedure with the read power exceeding 600 W±10% will result in damage to the optical pickup. 6. Press the key of the remote controller ("LP " changes to "RLDA " in the LCD). Specified range (read power): 600 W±10% or lower 7. Perfome the light power adjustment. Set the light power at 5.7mW by using VOL+, VOL-, EQ and PLAY MODE keys of the remote controller. If at this time the voltage between TP406 and TP407 is 85mA or higher, it is conceivable that theoptical pickup is defective. Specified range (light power): 5.7mW
Caution:
Do not allow the write power to even momentarily reach or exceed 6 mW. Doing so will result in damage to the optical pickup. 8. Press the key of the remote controller ("RLDA " changes to "LP " on the LDC. At this time, the data is written to EEPROM.). 9. Press the PLAY key on the remote controller ("LP " changes to "T0E** " on the LCD.). 10. Remove the laser power meter. Laser power adjustment is finished.
6.2.3. Off-set automatic adjustment
key of the 1. After laser power adjustment performed, press the remote controller and make "T1E** " display on the LCD . 2. Make the optical pickup move to center. 3. Press the PLAY key of remote controller without insert disc (change the display of the LCD to "0FADJ " , adjustment will be started.).
4. When it ends normally, "0FOK" is displayed on LCD of remote control and a main part. It is set to "0FNG" at the time of abnormalities. 5. Press the PLAY key of the remote controller (change the display of the LCD to "T1E** " , off-set automatic adjustment will be finished.).
Note) When "0FNG" is displayed, check "7. Troubleshooting Guide" in order.
6.2.4. Magneto-optical disc automatically adjustment
1. After "Off-set automatic adjustment" is finished, press the key of the remote control and make "T2E**" display on LCD.And move the optical pickup to around the center. 2. Set the full-recorded magneto-optical disc with the prevention erase situation. 3. Press the PLAY key of the remote controller ("T2E** " changes to "0AADJ " on the LCD, adjustment is started.). 4. If it has been finished normally, "0ADDJ " changes to "0AOK " on LCD. If it is abnormally, it changes to "0ANG ". 5. Press the PLAY key ("0AOK " or "0ANG " changes to "T2E** ", magneto-optical disc adjusment is finished.).
Note: When "0ANG" is displayed, check "7. Troubleshooting Guide" in order.
6.2.5. Playback-only disc automatically adjustment
1. After "Magneto-optical disc automatically adjustment" is finished, press the key of the remote control and make "T3J**" displayedon LCD. And move the optical pickup to around center. 2. Set the playback-only disc. 3. Press the PLAY key of the remote controller ("T3E** " changes to "00ADJ " on the LCD, adjusment is started.). 4. If it has been finished normally, "00ADJ " changes to "00OK " on
LCD. If it is abnormally, it changes to "00NG ". 5. Press the PLAY key ("00OK " or "00NG " changes to "T3E** ", playback-only disc adjustment is finished.).
Note: When "00NG" is displayed, check "7. Troubleshooting Guide" in order.
6.2.6. How to get out the adjustment mode
Remove the battery when you finish the adjustment mode.
6.3. Checking the main unit's keys 1. Set the battery and connect the remote controller. 2. Turn off the power. Then, with the main unit's HOLD switch at ON, press the buttons of the remote controller in order from 4 to 1. (as shown in Fig. 5 ) 3. When entering the main unit's key check mode, "E KEX " will be displayed on the LCD of main unit and remote controller. (If it is not displayed, perform the procedures written above again.) 4. Confirm the display of LCD by pressing any keys on the main unit. There is no order to press the keys.
Mian unit's keys PLAY STOP FOW REV HOLD OFF REC VOL+ VOLMARK MODE MODE EQ Letters on LCD A B C D E F G H I J K
5. Remote controller's LCD lights "E*** " and main unit's LCD lights all when you can detect all keys. 6. Perform below voltage check about the keys come under if you cannot detect the key.
Main unit's key PLAY STOP FOW REV HOLD OFF REC VOL+ VOLMARK MODE MODE EQ
Check point IC501 100pin IC501 100pin IC501 99pin IC501 99pin IC501 42pin IC501 100pin IC501 99pin IC501 99pin IC501 99pin IC501 99pin IC501 99pin
Voltage (ON) 0V 1.76V 0.66V 0.88V 0V 0.22V 1.1V 1.32V 0V 0.22V 0.44V
Voltage (OFF) 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V
7. "Checking the main unit's key" is finished. Remove the battery when you exit from this mode.
Note: Refer to "12. Printed Circuit Board Diagram" for the test points.
7. Troubleshooting Guide
7.1. Overall Flow Chart
7.1.1. Confirmation of main unit and remote control
7.1.2. Confirmation of main unit and cradle
7.2. Flow Chat of Each Part
8. Display of Self-Diagnostic Function
This model is equipped with a self-diagnosis function and shows, when necessary, the following indication in the LCD section of the set.
"F17"---This indication appears when the Down switch fails to turn ON since the magnetic head fails to move up/down normally (Due to trouble of the magnetic head or trouble of the magnetic head up/down motor)or the magnetic head P.C.B. is out of position or a foreign matter has mixed in or for some other reason. In such a case, check the peripheral parts of the magnetic head, repair or replace defective parts with normal ones.
9. Caution for Replacing EEPROM IC (IC502) and System Control IC (IC501)
Please be sure to perform "Laser power adjustment", "Off-set automatic adjustment", "Playback -only disc auto-adjustment" and "Magneto-optical disc auto-adjustment" after exchangingeither EEPROM IC (IC502) or the system control IC (IC501). (Please refer to "6. Measurements and Adjustment" about the adjustment method)
10. Schematic Diagram Notes
10.1. Schemtic Diagram Notes
This schematic diagram may be modified at any time with the development of new technology. Notes: : Magnetic head up switch (M.HEAD UP) S1 : PROTECT det., OP/ CL switch S501 S801 : Play / record / pause switch ( )
: Recording pause / LP recording switch (REC S802 / LP MODE) S803 S804 S805 S806 : Volume - switch (VOL-) S807 : Stop / operation off switch ( : Forward skip switch ( : Reverse skip switch ( : Volume + switch (VOL+) ) ) OPR OFF)
: Hold switch in "OFF" position. (HOLD) S806
- Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on theinternal impedance of the DC circuit tester.
No mark: MD STOP ( ): MD PLAY < >: MD REC Important safety notice: mark have special characteristics important for safety. Components identified by Furthermore, special parts which have purpose of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture's specified parts shown in theparts list. Caution!
IC and LSI are sensitive to static electricity. Secondary trouble can be prevented by taking care during repair. Cover the parts boxes made of plastics with aluminum foil. Ground the soldering iron. Put a conductive mat on the work table. Do not touch the legs of IC or LSI with the fingers directly.
Voltage and signal line : Positive voltage line : Playback signal line : Recording signal "digital" line : Recording signal "analog" line : Mic signal line
10.2. Type Illustration of IC's, Transistors and Diodes
11. Schematic Diagram 12. Printed Circuit Board Diagram 13. Block Diagram
14. Wiring Connection Diagram 15. Terminal Function of IC's
15.1. IC1 (AN22010A-VF) : RF AMP
Pin No. 1 2 3 4 5 6 7 8 Mark LDO LD IN APCPD APC REF ARFO NC EQ IN CRF AGC I/O Division O I I I O -- I I Function Laser amp output terminal Laser amp reverse input terminal Photo diode light quantity det. input terminal APC amp reference voltage input terminal RF amp. output terminal Not used, open EQ input terminal RFAGC capacitor connection input terminal (Connected to GND through capacitor) EFM signal output terminal Not used, open EFM bright side det. output terminal GND terminal EFM dark side det. output terminal 3T envelope det. capacitor connection terminal (Connected to power supply through capacitor) AS/3TMON signal output terminal C signal dark side det. / amplifier output terminal D signal dark side det. / amplifier output terminal Power supply terminal (+ 3V) B signal I/V converter output terminal A signal I/V converter output terminal
9 10 11 12 13 14
OUT RF NC PEAK GND BOTM CEA
O -- O -- O I
15 16 17 18 19 20
MON3T CC DD VCC BB AA
O O O I O O
Pin No. 21 22 23,24 25 26 27 28 29 30 31
Mark FF2 FF1 NC ADIP NC NREC RFSWHL RFSWPG GND NC
I/O Division O O -- O -- I I I -- -- I I I I O I I I I I O I I I
Function F2 signal I/V converter output terminal F1 signal I/V converter output terminal Not used, open ADIP signal output terminal Not used, open REC/PLAY select signal input terminal Reflect H/L select signal input terminal Pit / group select signal input terminal GND terminal Not used, open 3TMON circuit control signal input terminal ADIP BPF select signal input terminal ACP circuit control signal input terminal Standby control signal input terminal Temperature sensor amp output terminal Temperature sensor amp input terminal F1 signal input terminal F2 signal input terminal Main beam A signal input terminal Main beam B signal input terminal Reference voltage output terminal RF2 signal input terminal RF1 signal input terminal D signal det. capacitor input terminal (Not used, open) C signal detection capacitor input terminal (Not used, open)
32 MONIOFF 33 34 CLV2 LDON
35 NRFSTBY 36 37 38 39 40 41 42 43 44 45 TEMP TEMP IN F1 F2 A B VREF RF2 RF1 CENVD
46
CENVC
I
Pin No. 47 48
Mark D C
I/O Division I I
Function Main beam D signal input terminal Main beam C signal input terminal
15.2. IC101 (M66621BSG) : ATRAC ENCORDER/DECORDER, SERVO SIGNAL PROCESSOR
Pin No. 1 2 3 4 Mark TS0 APCD RFSWPG RFSWHL I/O Division I O O O Function Test input terminal (Not used, connected to GND) Laser power setting PWM output terminal Pit / group setting signal output terminal High / low reflection setting signal output terminal High speed select signal output terminal EFM signal output terminal Spindle (-) drive signal output terminal Spindle (+) drive signal output terminal Focus (-) drive signal output terminal Focus (+) drive signal output terminal Tracking (-) drive signal output terminal Tracking (+) drive signal output terminal Power supply input terminal ( For digital circuit) LD lighting control signal output terminal Traverse (-) drive signal / stepper drive signal 0 output terminal
5 6 7 8 9 10 11 12 13 14 15
CLV2 REFM SPDM SPDP FODM FODP TRDM TRDP DVDD0 LDON TVDM/ STPO0
O O O O O O O O -- O O
Pin No. 16
Mark TVDP/ STPO1 SBCK/ STPO2 SUBC/ STPI0 BLKCK/ STPI1 NCLDCK / STPI2 NREC DRVSEL
I/O Division O
Function Traverse (+) drive signal / stepper drive signal 1 output terminal Sub code Q clock for resistor / stepper drive signal 2 output terminal Sub code Q / stepper status 0 input terminal Sub code block clock signal / stepper status 1 input terminal Sub code flame clock signal / stepper status 2 input terminal REC / PLAY select signal output terminal Driver mode select input terminal (Connected to GND) CD data / FG input terminal CD bit clock input terminal CD word clock input terminal External ADC / DAC clock output terminal (384FS) Audio data input terminal Audio data output terminal (Not used, open) Word clock output terminal Bit clock output terminal Digital audio interface 2 input terminal (Not used, open) Digital audio interface 1 input terminal Digital audio interface output terminal (Not used, open) Power supply terminal GND terminal Frame synchronous signal output terminal Leader synchronous signal output terminal
17
O
18 19
I I
20
I
21 22
O I
23 24 25 26 27 28 29 30 31
DATA/FG BCK LRCK MONI4 SDAR SDAP SWS SCL RX2
I I I O I O O O I
32 33
RX1 TX
I O
34 35 36 37
DVDD1 DVSS1 SGSYNC MDISY
-- -- O O
output terminal Pin No. 38 39 40 41 42 43 44 45 46 Mark SCTSY SSDR SSDW SSCK SELAD MONI1 MONI2 MONI3 NRST I/O Division O O I I I O O O I -- O O -- -- I I I I I I I -- I I Function ADIP synchronous noise output terminal System control read data output terminal System control write data input terminal System sift clock signal input terminal System control address signal select input terminal Monitor 1 output terminal (Not used, open) Monitor 2 output terminal (Not used, open) Monitor 3 output terminal (Not used, open) Hardware reset signal input terminal GND terminal Audio Rch output terminal Audio Lch output terminal Power supply terminal GND terminal Servo A/D converter input terminal Servo A/D converter input terminal Servo A/D converter input terminal Servo A/D converter input terminal Reference voltage input terminal Servo A/D converter input terminal Servo A/D converter input terminal Power supply terminal Servo A/D converter input terminal Servo A/D converter input terminal
47 PWMVSS 48 49 51 52 53 54 55 56 57 58 59 60 61 ADACR ADACL AVSS0 PEAK BOTM OSC MON3T VREF1 FF2 FF1 AVDD0 DD CC
50 PWMVDD
Pin No. 62 63 64 65 66 67
Mark BB AA AVSS1 PEFMS PEFM1 EFMFIL
I/O Division I I -- I O O O I
Function Servo A/D converter input terminal Servo A/D converter input terminal GND terminal EFM signal input terminal EFM data slice roop filter 1 output terminal EFM data slice roop filter 2 output terminal Filter for EFMPLL output terminal Reference voltege for EFMPLL setting input terminal ADIP signal input terminal Power supply terminal Monitor 0 output terminal (Not used, open) Address for DRAM 11 output terminal (Not used, open) Address for DRAM 10 output terminal Address for DRAM 9 output terminal Address for DRAM 8 output terminal Address for DRAM 7 output terminal Address for DRAM 6 output terminal Connected to GND Address for DRAM 5 output terminal Address for DRAM 4 output terminal Address for DRAM 3 output terminal Address for DRAM 2 output terminal Address for DRAM 1 output terminal
68 EFMPLLF 69 EFMIREF
70 71 72 73
ADIP AVDD1 MONI0 RAD11
I -- O O
74 75 76 77 78 79 80 81 82 83 84
RAD10 RAD9 RAD8 RAD7 RAD6 DVSS2 RAD5 RAD4 RAD3 RAD2 RAD1
O O O O O -- O O O O O
Pin No. 85 86 87 88 89 90 91 92
Mark DVDD2 RAD0 RDT3 IVDD1 RDT2 RDT1 RDT0 NRAS
I/O Division I O I/O -- I/O I/O I/O O
Function Power supply input terminal Address for DRAM 0 output terminal Data for DRAM 3 input / output terminal Power supply for I/O pad Data for DRAM 2 input / output terminal Data for DRAM 1 input / output terminal Data for DRAM 0 input / output terminal Load address strobe for DRAM signal output terminal Calam address strobe for DRAM signal output terminal Write enable signal for DRAM output terminal Test input terminal (Not used, connected to GND) GND terminal Crystal oscillator output terminal (F=16.9344MHz) Crystal oscillator input terminal (F=16.9344MHz) Power supply for I/O pad Test input terminal (Not used, connected to GND)
93
NCAS
O
94 95 96 97 98 99 100
NWE TS2 DVSS0 XO XI IVDD0 TS1
O I -- O I -- I
15.3. IC401 (C0GBZ0000020) : FOCUS/TRACKING COIL, TRAVERSE MOTOR DRIVE, SPINDLE MOTOR DRIVE, ROTARY DETECTOR
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Mark IN 1R IN 2F IN 2R STALL STHB SP VM1 SP U OUT SP PG1 NC SP V OUT SP VM2 SP W OUT SP PG2 PWVM PWOUT
I/O Division I I I I I I O -- -- O I O -- I O
Function H bridge 1 reverse input terminal H bridge 2 forward input terminal H bridge 2 reverse input terminal Standby input terminal H1, H2 bridge mute input terminal Half bridge 1 input terminal Spindle motor coil (U) output terminal GND terminal Not used, open Spindle motor coil (V) output terminal Half bridge input terminal Spindle motor coil (W) output terminal GND terminal Power supply terminal Hlaf bridge 1 output terminal (Not used, open) GND terminal Half bridge 1 input terminal Roter position detect comparater (U) input terminal Roter position detect comparater (V) input terminal Roter position detect comparater(W) input terminal Spindle motor coil center input terminal Connected to GND through resistor Connected to GND through capacitor Slope capacitor connection terminal
16 17 18
PWPG PWIN1 SP U IN
-- -- I
19
SP V IN
I
20
SPWIN
I
21 22 23 24
SPCOM RIB CST CSL1
I -- -- I
terminal Pin No. 25 26 27 Mark CSL2 FG BRK+ I/O Division I O I Function Slope capacitor connection terminal Speed pulse output terminal Brake comparater+ input terminal (Connected to power supply through resistor) Brake comparater- input terminal GND terminal GND terminal Stepping decorder 1 input terminal Stepping decorder 2 input terminal Stepping decorder 3 input terminal Step detect comparater (U) output terminal Step detect comparater (V) output terminal Step detect comparater (W) output terminal Step motor coil center input terminal GND terminal Stepping motor (W) output terminal Power supply terminal Stepping motor (V) output terminal Stepping motor (V) output terminal (Connected to GND) Stepping motor (U) output terminal Power supply terminal Power supply terminal Power supply terminal Charge pump output terminal (Connected to GND through capacitor)
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
BRKASGND SGND S1 S2 S3 BEMFU BEMFV BEMFW SLCOM SLPG2 SLWOUT SLVM2 SLVOUT SLPG1
I -- -- I I I O O O I -- O I O O
43 44 45 46 47
SLUOUT SLVM1 VCC 2 VCC 1 VG
O I I I O
Pin No. 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Mark C2M C2P C1M C1P EXTCLK NC H2 PG2 H2 R OUT H2 VM H2 F OUT H2 PG1 H1 PG2 H1 R OUT H1 VM H1 F OUT H1 PG1 IN 1F
I/O Division -- -- -- -- -- -- -- O I O -- -- O I O -- I
Function Charge pump capacitor 2(-) connect terminal Charge pump capacitor 2(+) connect terminal Charge pump capacitor 1(-) connect terminal Charge pump capacitor 1(+) connect terminal Not used, open Not used, open GND terminal H bridge 2 reverse output terminal Power supply terminal H bridge 2 forward output terminal GND terminal GND terminal H bridge 1 reverse output terminal Power supply terminal H bridge 1 forward output terminal GND terminal H bridge 1 forward input terminal
15.4. IC501 (C2DBKJ000062) : SYSTEM CONTROL
Pin No. 1 2 3 4 5 6
Mark AVREFO AVDD AVSS P80/ ANO0 P80/ ANO1 AVREF1
I/O Division I -- -- -- -- I
Function Reference voltage input terminal for A/V converter Power supply terminal for A /V converter (+2.2V) Connected to GND Connected to GND Connected to GND Reference voltage input terminal for D/A converter (Connected to GND) Connected to GND LINK serial communication RXD input terminal Remote control LCD driver data output terminal Not used, open Power supply terminal (+ 2.2V) GND terminal Main clock input terminal (f =10.0MHz) Main clock output terminal (f=10.0MHz) RESET input terminal Sub clock input terminal (Not used, connected to GND) Sub clock output terminal (Not used, open) Not used, connected to GND Power supply input terminal (+2.2V) Microcomputer debug terminal (Open) Microcomputer debug terminal (Open) Unit key WAKE UP signal input terminal
7 8
NMI LINK RXD
-- I O -- -- -- I O I --
9 REM_DATA 10 11 12 13 14 15 16 P32/ SCK1 VDD VSS X1 X2 RESET XT1
17 18 19 20 21
XT2 VSSBU VDDBU DEBUG1 DEBUG2
-- -- -- O O
22 H_KEY_WAKEUPI
Pin No.
Mark
I/O Division
Function Remote control key WAKE UP signal input terminal Doctor mode signal input terminal (Open) NET MD microcomputer (IC1101) communication request signal output terminal (Not used, open) NET MD microcomputer (IC1101) communication reset signal output terminal (Not used, open) NET MD microcomputer (IC1101) communication chip select signal output terminal (Connected to GND through resistor) Cradle control signal output terminal Not used, open MSP/MDA I/F reading data input terminal MSP/MDA I/F writing data output terminal MSP/MDA I/F clock output terminal Test terminal (Open) Unit LCD driver data output terminal Unit LCD driver clock output terminal GND terminal Power supply terminal (+ 2.2V) MSP/MDA I/F address select signal output terminal Unit LCD power control output terminal (+2.2V) LCD driver strobe signal output terminal Erase prevention switch input terminal (H : protect)
23 REM_KEY_WAKEI UP 24 25 DOCTOR M_REQ I O
26
M_RST
O
27
M_CS
I
28 29 30 31 32
SP_CNT P99/A9/ TXD1 SSDR SSDW SSCLK
O -- I O O I O O -- -- O
33 LSI_STAT 34 LCD_DATA 35 36 37 38 LCD_CK EVSS EVDD SELAD
39 LCD_CNT 40 LCD_STB 41 PROTECT
O O I
Pin No.
Mark
I/O Division I I I I I O O O O I/O
Function HOLD switch input terminal (H : hold) DC IN detection input terminal (H : DC IN) DC IN2 detection input terminal (H : DC IN2) Input select detection input terminal Mic input detection input terminal (L : Mic) Mic/LINE select output terminal Mic sensitivity select output terminal Magnetic head EFM drive control output terminal Charge select output terminal (H : charge) EL lighting control input/ output terminal (L : lighting) EEPROM (IC502) chip select output terminal EEPROM (IC502) clock output terminal EEPROM (IC502) data output terminal EEPROM (IC502) data input terminal ADC/PGA I/F data output terminal ADC/PGA I/F chip select output terminal ADC/PGA I/F clock output terminal ADC/PGA I/F reset output terminal USB connection select output terminal (Not used, open) USB connection power control output terminal (Not used, open) GND terminal
42 HOLD_SW 43 DCIN_DET 44 DCIN_DET2 45 INSEL
46 MIC_DET 47 MIC/LINE
48 MIC_SENS 49 50 51 EFMON CHARGE EL_ON
52 EE_P_CS 53 EE_P_CK
O O
54EE_P_DATAO O 55 EE_P_DATAI 56 AKM_CDTI 57 AKM_CSN 58 AKM_CCLK 59 AKM_PDN I O O O O
60USB_SELECT O
61 USB_CNT
O
62
IC
--
Pin No. 63 64 65
Mark EVSS EVDD HFON1
I/O Division -- -- O O O O O O O
Function GND terminal Power supply terminal (+ 2.2V) HF module ON signal output terminal 3T monitor OFF output terminal (H : OFF) REC control output terminal 2 REC control output terminal 1 RF power control terminal Power control terminal 4ch driver stand-by signal output terminal (L : standby) FD/TR coil power control output terminal RF amp stand-by output terminal (L : stand-by) MSP reset signal output terminal (L : reset) Analog mute A signal output terminal USB connection MD LSI power select terminal NET MD I/F data input terminal (Connected to GND through resistor) NET MD I/F data output terminal (Not used, open) NET MD I/F clock output terminal (Not used, open) Magnetic head moving control output terminal Magnetic head moving direction control output terminal Magnetic head DOWN detection input terminal (L : DOWN) Buzzer signal output termnial
66 MONIOFF 67 REC_CNT2 68 REC_CNT1 69 71 RF_CNT PC
70 PWR_CNT
72
STBY2
O O O O
73 NRFSTBY 74 75 MSPRST MUTE_A
76 USB_SELECT2 O 77 M_DATA_I I
78 M_DATA_O 79 M_CLK_O 80 81 LOAD0 LOAD1
O O O O
82 MHEAD_UP
I
83
BUZZER
O
Pin No.
Mark
I/O Division I
Function Disc cover open/close detection terminal (H : open) Microcomputer wake up signal input terminal ADIP syncronize signal input terminal from IC101 MDA syncronized signal input terminal from IC101 Headder syncronize signal input terminal from IC101 Not used, connected to GND Not used, connected to GND DC IN connection terminal USB connection terminal Temperature sensor input terminal Battery voltage detection terminal 1 Remote control key input terminal Key pat input terminal 3 Key pat input terminal 2 Key pat input terminal 1 Unit key input terminal 2 Unit key input terminal 1
84 OPENSW
85 86 87 88 89 90 91 92 93 94
WAKEUP SCTSY CFSYNC MDISY P711/ ANI11 P710/ ANI10 DCIN USBIN ONDO BATT1
I I I I -- -- I I I I I I I I I I
95 REM_KEY 96 97 98 99 P_KEY3 P_KEY2 P_KEY1 H_KEY2
100 H_KEY1
16. Caution in Use of Rechargeable Battery Ass'y
- Take Rechargeable Battery Ass'y out of Battery Carrying Case and use it. - Be sure to carry Rechargeable Battery Carrying Case. If not, it may either heat or ignite by shorting with a metal. (as shown in Fig. 10 )
Fig. 10
17. Replacement Parts List
Notes: *Important safety notice: mark have special characteristics important for safety. Components identified by Funrthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture's specified parts shown in the parts list. *Warning: This product uses a laser diode. Refer to caution statements. *ACHTUNG:Die lasereinheit nicht zerlegen.Die lasereinheit darf nur gegen einc vom hersteller spezifizierte einheit ausgetauscht werden. *Capacity values are in microfarads (uF) unless specified otherwise, P=Pico-farads (pF) F= Farads (F) *Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM), 1M=1,000K (OHM) *The marking indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. *""-"" marks in Remarks indicate languages of instruction manuals. [: English,: Chinese] *All parts are supplied by MESA.
Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 32 32 32 32 32 32-1 32-2 32-3 32-4 33 34 35 36 37 38 39 39-1 40 41 41 42 43 44 44-1
Part No. RHD14080 RDG0510 RHD14078 RHW11011 RMC0437 BRL1A1CWD RDG0482-1 RHW06001 RMB0650 RML0586-3 RML0587-3 RMM0230-1 RXG0050 RXK0318-5 RXM0071-1 RFKQMR220S RXM0074-1 RXJ0030 RJC99039-1 RJR0220 RHD14104-X RMR1476-X L5ACAFC00003 RGP0950-Q RGU2135-S2 RHQ0083-S RJB2640A RXM0077 RMZ0644 RYF0647A-A RYF0647A-S RYF0647B-A RYF0647B-R RYF0647B-S RGV0286-S RGV0303-S RMA1587 RMQ1145 K0RE00300010 RGK1545-S1 RGU2137-S RGV0304-S RHQ0083-S RMQ1144 RXQ0921-1 RMB0725-1 XQN14+B2FC RYK1245B-S RYK1245C-S RHD14094-S RKK0165-S RXK0383 BRL1A1CWF
Part Name & Description SCREW INTERMEDIATE GEAR SCREW WASHER SPRING LIFT MOTOR REDUCTION GEAR WASHER EJECT SPRING LIFTER LINK EJECT ROD A TRANSFER GEAR HOLDER UNIT EJECT ROD B OPT MAGNETISM HEAD UNIT ARM DRIVE SHAFT UNIT RECHARGE.BATT.TERMINAL(+) BATTERY SHAFT SCREW PWB SPACER LCD LCD PANEL OPERAITON BUTTON SCREW OPERATION FPC LINK UNIT INSULATION SHEET DISC COVER ASS'Y DISC COVER ASS'Y DISC COVER ASS'Y DISC COVER ASS'Y DISC COVER ASS'Y HOLD KNOB REC KNOB REC LEVER REC KNOB SHEET MEMBRANE SW INTERMEDIATE CABINET BUTTON,EQ/MODE/MARK OPEN KNOB SCREW OPEN KNOB SHEET LOCK UNIT LOCK SPRING SCREW CABINET ASS'Y CABINET ASS'Y SCREW RECHARGEABLE BATT.COVER TRAVERSE CHASSIS ASS'Y TRAVERSE MOTOR
Pcs 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 1 1 1 1 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 (GHA) (GHS) (GKA) (GKR) (GKS)
Remarks
(GHA)(GHS) (GKA)(GKR)(GKS)
Ref. No. 44-2 44-3 44-4 44-5 44-6 44-7 45 46 A1 A1 A1 A2 A3 A3-1 A3-2 A4 A4-1 A5 A6 A6 A7 A8 A8 A9 A9 A11 A12 A13 A13-1 A14 C1 C2 C3 C4 C5 C20 C30 C34 C35 C50 C51 C52 C53 C101 C102 C103 C104 C105 C106 C107 C109,10 C111
Part No. K0L2LF000002 RHD14082 RMA1364-2 RMX0156-1 XQN14+B4FC XQN14+C12FZ XQN14+A12FC RMZ0670 RQT6862-B RQT6864-K RQT6863-K L0BAB0000174 N2QCBD000012 RFKY0003 RFKY0004 RFKFFAZ01EM1 RFA0475-Q RFA1537-S2 RFKAJMR250-S RFKAMR230GKS RFC0069-H RFE0114A RFE0114B RFEA413H-W RFEA413T-1W K2KA39B00001 K7CXJCA00004 L0BAE0000026 RFX3558 RQCB1205-1 F1G1H221A416 ECUVNA154KBV ECUVNC104ZFN F1G1E472A059 ECJ1VB0J105K F5A422240001 F1J0J4750016 F3E0G106A001 F5A421040002 ECUENA104KBQ ECJ0EB1H102K ECUENA104KBQ ECUVNJ474KBV F3E0G106A001 ECUENA104KBQ F3E0G106A001 ECUENA104KBQ F3E0G106A001 ECUENA104KBQ F3G0G2270001 F1G1H100A420 ECUE1H470JCQ
Part Name & Description SWITCH(S501) SCREW HOLDER ANGLE STOPPER RUBBER SCREW SCREW SCREW SPACER INSTRUCTION MANUAL INSTRUCTION MANUAL INSTRUCTION MANUAL STEREO EARPHONES WIRED REMOTE CONTROL PANEL ASS'Y CLIP ASS'Y RECHARGEABLE BATT.ASS'Y RECHARGEABLE BATT.CASE EXTERNAL BATTERY CASE SPEAKER ASS'Y SPEAKER ASS'Y CARRYING CASE CLADRE CLADRE AC ADAPTER AC ADAPTER CONNECTION CABLE OPTICAL FIBER CABLE CLIP TYPE HEADPHONES EAR PAD SERVICE CENTER LIST 50V 220P 10V 0.15U 16V 0.1U 25V 4700P 6.3V 1U 4V 0.22U 6.3V 4.7U 4V 10U 4V 0.1U 10V 0.1U 50V 1000P 10V 0.1U 6.3V 0.47U 4V 10U 10V 0.1U 4V 10U 10V 0.1U 4V 10U 10V 0.1U 4V 220U 50V 10P 50V 47P
Pcs 1 1 1 2 1 2 2 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1
Remarks
(GH) (GK)
(GHA)(GHS) (GKA)(GKR)(GKS) (GHA)(GHS) (GKA)(GKR)(GKS) G4C4CAD00002 (GH) G4C4CAJ00010 (GK)
(GKA)(GKR)(GKS)
F1H1A154A028 F1J1C104A081
F1G1A104A014 F1G1A104A014 F1H0J474A002 F1G1A104A014 F1G1A104A014 F1G1A104A014
F1G1H470A422
C111
ECUE1H470JCQ
50V 47P
1
F1G1H470A422
Ref. No. C113 C120 C121 C122 C123 C130 C140 C201 C202 C204,05 C206 C207 C211 C212 C213,14 C215,16 C220 C301 C302 C303 C304 C305 C306 C307 C308 C310 C312 C313 C316 C317 C318 C401 C402 C403 C404 C411 C412-14 C415-17 C418 C419 C501 C502 C505 C506,07 C508 C510 C513 C516 C601 C602 C603 C605 C606 C608
Part No. F1G1C103A044 ECUENA104KBQ ECUE1C223KBQ F1G0J224A004 ECUE1E681KBQ F1G1E472A059 F1G1C103A044 F1J0J4750016 ECUVNJ334KBV F3E0G106A001 F5A421040002 F1G1H331A416 F5A421050001 F5A421020001 ECJ1VB0J105K F3G0G2270001 ECJ0EB1H101K RCST0EC397RE RCST0JX107RG F3Z0G107A003 RCST0JX107RG ECJ1VB0J105K ECUENA104KBQ F1J0J106A013 ECUENA104KBQ ECUENA104KBQ ECUENA104KBQ F1G1C103A044 F1J0J106A013 F1J0J4750016 ECUENA104KBQ F1J0J4750016 ECUENA104KBQ ECJ1VB0J105K F5A421040002 F3E0G2260001 F1G1H222A416 ECUENC333KBQ ECUVNJ334KBV F5A421040002 F3E0G2260001 ECUENA104KBQ F1G1C103A044 ECJ0EB1H101K ECUENA104KBQ ECUVNJ474KBV F1G1C103A044 ECJ1VB0J105K F1J0J4750016 F1G1C103A044 F1J0J4750016 F3E0G156A001 ECJ1VB0J105K ECJ0EB1H102K
Part Name & Description 16V 0.01U 10V 0.1U 16V 0.022U 6.3V 0.22U 25V 680P 25V 4700P 16V 0.01U 6.3V 4.7U 6.3V 0.33U 4V 10U 4V 0.1U 50V 330P 4V 1U 4V 1000P 6.3V 1U 4V 220U 50V 100P 2.5V 390U 6.3V 100U 4V 100U 6.3V 100U 6.3V 1U 10V 0.1U 6.3V 10U 10V 0.1U 10V 0.1U 10V 0.1U 16V 0.01U 6.3V 10U 6.3V 4.7U 10V 0.1U 6.3V 4.7U 10V 0.1U 6.3V 1U 4V 0.1U 4V 22U 50V 2200P 16V 0.033U 6.3V 0.33U 4V 0.1U 4V 22U 10V 0.1U 16V 0.01U 50V 100P 10V 0.1U 6.3V 0.47U 16V 0.01U 6.3V 1U 6.3V 4.7U 16V 0.01U 6.3V 4.7U 4V 15U 6.3V 1U 50V 1000P
Pcs 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1
Remarks F1G1A104A014 F1G1C223A044
F1H0J334A002
F3H0J397A012 F3G0J1070002 F3G0J1070002 F1G1A104A014 F1G1A104A014 F1G1A104A014 F1G1A104A014
F1G1A104A014 F1G1A104A014
F1G1C333A004 F1H0J334A002
F1G1A104A014
F1G1A104A014 F1H0J474A002
Ref. No. C701 C702 C704 C711 C713,14 C721 C722 C725,26 C727,28 C801 C802 C803 C804 C805 C808 C901 C902 C903 C904-06 C907 C908 C911 C912 C914 C915 CN1 CN2 CN3 CN403,04 CN501 CN502 CN901 CN1301 CP801 CP802 D1 D301 D304 D501 D910 D911,12 IC1 IC101 IC102 IC201 IC301 IC302 IC303 IC304 IC305
Part No. RCST0JY226RG ECUENA104KBQ F3E0G106A001 ECUENA104KBQ F5A421050001 F5A421040002 F5A421020001 F1J0J4750016 F3E0G106A001 F5A421050001 F5A421040002 F1G1C103A044 ECJ1VB0J105K F1G1E472A059 F1G1C103A044 F3E0G2260001 F5A422240001 ECUENA473KBQ F1G1E472A059 F1G1C103A044 ECUENA104KBQ ECUENA104KBQ F1J0J4750016 ECJ0EC1H030C ECUENA473KBQ K1MN21B00045 K1MN06B00069 K1MN04B00034 K1MN04B00034 K1MN10B00064 K1MN06B00114 K1MN10B00064 K4BZ14E00001 K1MN10B00097 K1MN15B00092 MA2S11100L MA2S11100L B0JCJB000001 MA3S781D0L MA3S13300L MA2YD2600L AN22010A-VF MN66621BSG C3ABMB000026 C1BB00000720 C0ABHA000037 C0DBAFZ00021 XC6367A151MR C0DBAGZ00018 C0CBAAG00012
Part Name & Description 6.3V 22U 10V 0.1U 4V 10U 10V 0.1U 4V 1U 4V 0.1U 4V 1000P 6.3V 4.7U 4V 10U 4V 1U 4V 0.1U 16V 0.01U 6.3V 1U 25V 4700P 16V 0.01U 4V 22U 4V 0.22U 10V 0.047U 25V 4700P 16V 0.01U 10V 0.1U 10V 0.1U 6.3V 4.7U 50V 3P 10V 0.047U CONNECTOR(21P) CONNECTOR(6P) CONNECTOR(4P) CONNECTOR(4P) CONNECTOR(10P) CONNECTOR(6P) CONNECTOR(10P) CONNECTOR(14P) CONNECTOR(10P) CONNECTOR(15P) DIODE DIODE DIODE DIODE DIODE DIODE IC IC IC IC IC IC IC IC IC
Pcs 1 1 1 1 2 1 1 2 2 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1
Remarks F3F0J2260002 F1G1A104A014 F1G1A104A014
F1G1A473A014
F1G1A104A014 F1G1A104A014
F1G1A473A014
C0DBAFZ00012
Ref. No. IC306 IC307,08 IC401 IC501 IC502 IC503 IC601 IC701 IC901 IC902 JK201 JK701 JK702 L1,L2 L101 L201,02 L204,05 L301 L302 L303 L411 L501 L701-03 L720-22 P1 P1 P1 P1 P1 P2 P2 P3 P4 PCB1 PCB2 PCB3 Q1 Q2 Q3 Q202 Q203 Q301 Q303 Q304 Q305 Q307 Q308 Q310 Q311
Part No. C0CBAAB00036 B1KBB0000006 C0GBD0000022 C2DBKJ000062 C3EBDG000039 C0EBC0000035 C0FBAJ000008 C1BB00000609 C0GBE0000003 C0JBAZ001928 RJJ36TK03-1C B3MAZ0000026 K2HC103E0016 RLQP100MT-W RLQP100MT-W RLBV601V-W RLBV601V-W G1A330D00007 G1A220D00002 G1A330D00009 ELJEA470KF RLQP100MT-W RLBV601V-W RLBV601V-W RPK1869 RPK1868 RPK1871 RPK1872 RPK1870 RPQ1486 RPQ1488 RPQ1489 RPQ1487 REP3036A-M REP3418B-M REP3417A-S B1ADMB000003 B1GDCFJJ0001 DTC144EETL B1ADMB000003 B1ABDF000001 B1ABDF000001 B1HFCFA00005 B1CFNC000001 B1CHMC000001 B1CFNC000001 2SB1462STX B1MBADA00001 B1ADKB000003 IC IC IC IC IC IC IC IC IC IC
Part Name & Description
Pcs 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 1 1 3 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 [RTL] [RTL] [RTL]
Remarks
JACK,HEADPHONE JACK,OPT/LINE JACK,MIC COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PAD PAD PAD PAD REC.HEAD P.C.B. MAIN P.C.B. OPERATION P.C.B. TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
K2HC106E0001
G1C100M00016 G1C100M00016 J0JCC0000059 J0JCC0000059
G1C100M00016 J0JCC0000059 J0JCC0000059 (GHA) (GHS) (GKA) (GKR) (GKS) (GH) (GK)
B1GBCFNN0001
2SB14620SL
Ref. No. Q312 Q313 Q315 Q701 Q702 Q703 Q901 Q910 Q911,12 Q913,14 R1 R2 R3 R5 R6 R7 R9 R11 R41 R42 R101 R102 R110 R120 R121 R122 R123 R130 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R212 R215 R301 R302 R303 R304 R305 R306,07 R308 R309 R310 R311 R312 R313 R314
Part No. B1CHMC000001 B1CHHD000003 DTC144EETL B1HFCFA00005 DTC144TETL 2SB1462STX DTC144EETL DTC144EETL B1DFCC000008 B1DFBG000004 D1H447220001 ERJ2GEJ272 ERJ2GEJ1R5X ERJ2GEJ271 ERJ2GEJ150 ERJ2GEJ474X ERJ2GEJ223X ERJ2GEJ222X ERJ2GEJ103 ERJ2GEJ473X ERJ2GEJ105 ERJ2GEJ221 D1H84704A024 ERJ2GEJ123 D1H433320002 ERJ2GE0R00X ERJ2GEJ221 ERJ2GEJ222X ERJ2GEJ221 ERJ2GEJ471X D1BA2702A007 D1H410320002 ERJ2GEJ104 D1H410320002 D1H433220001 EXB24V225JX D1H410020002 D1H422120001 D1H447320001 D1H422120001 ERJ2GEJ334X D1H410420002 D1BA8202A007 ERJ2GEJ103 ERJ2GEJ101 ERJ8GEY0R00V D1H447420001 ERJ2GEJ394X D1BA3302A007 D1BA1203A007 ERJ3GEYJ335V D1H81044A024 ERJ2GEJ154
Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 4.7K 1/4W 2.7K 1/4W 1.5 1/4W 270 1/4W 15 1/4W 470K 1/4W 22K 1/4W 2.2K 1/4W 10K 1/4W 47K 1/4W 1M 1/4W 220 47 1/4W 12K 33K 1/4W 0 1/4W 220 1/4W 2.2K 1/4W 220 1/4W 470 27K 10K 1/4W 100K 10K 3.3K 1/4W 2.2M 10 220 47K 220 1/4W 330K 100K 82K 1/4W 10K 1/4W 100 1/8W 0 470K 1/4W 390K 33K 120K 1/16W 3.3M 100K 1/4W 150K
Pcs 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1
Remarks
B1GBCFNN0001 B1GBCFNA0001 2SB14620SL B1GBCFNN0001 B1GBCFNN0001
ERJ2RMJ474X ERJ2RMJ223X ERJ2RMJ222X ERJ2RMJ473X D0GA105JA001
D0YAR0000003 ERJ2RMJ222X ERJ2RMJ471X
ERJ2RMJ334X
D0YFR0000002 ERJ2RMJ394X
Ref. No. R315 R317 R318 R320 R321 R322 R323 R324 R325 R326 R328 R401 R411 R412 R431 R501 R502 R503 R504 R505 R506 R508 R509 R510 R511 R512 R514,15 R516 R601 R701 R702 R703 R704 R705 R706 R707 R708 R709 R711 R712 R713 R714 R801 R802 R803 R804 R805 R806 R807 R808 R901 R902 R903 R904
Part No. ERJ2GED513X ERJ6RSJR10V ERJ2RKD474X D1H81044A024 ERJ2GEJ394X ERJ2GEJ225X ERJ2GEJ105 D1BA3303A007 D1BA2203A007 ERJ2GEJ474X ERJ2GEJ474X D1H447320001 ERJ2GEJ471X ERJ2GEJ682X ERJ2GEJ103 ERJ2GEJ473X ERJ2GEJ104 D1H83344A024 ERJ2GEJ104 ERJ2GEJ221 D1H422420001 ERJ2GEJ103 ERJ2GEJ223X ERJ2GEJ334X D1H82244A024 D1H81034A024 ERJ2GEJ122 ERJ2GEJ102X ERJ2GEJ4R7X ERJ2GEJ101 ERJ2GEJ224 D1H410420002 ERJ2GEJ334X ERJ2GEJ473X D1H418220001 D1H422320002 D1H418220001 D1H410320002 ERJ2GEJ471X D1H81044A024 ERJ2GEJ101 ERJ2GEJ103 ERJ2GEJ122 ERJ2GEJ393X ERJ2GEJ272 ERJ2GEJ332X ERJ2GEJ472X ERJ2GEJ182 ERJ2GEJ154 ERJ2GEJ334X ERJ2GEJ682X ERJ2GEJ153 ERJ2GEJ182 ERJ2GEJ331X
Part Name & Description 1/4W 51K 1/10W 0.1 1/4W 470K 100K 1/4W 390K 1/4W 2.2M 1/4W 1M 330K 220K 1/4W 470K 1/4W 470K 47K 1/4W 470 1/4W 6.8K 1/4W 10K 1/4W 47K 1/4W 100K 330K 1/4W 100K 1/4W 220 220K 1/4W 10K 1/4W 22K 1/4W 330K 220K 10K 1/4W 1.2K 1/4W 1K 1/4W 4.7 1/4W 100 1/4W 220K 100K 1/4W 330K 1/4W 47K 1.8K 22K 1.8K 10K 1/4W 470 100K 1/4W 100 1/4W 10K 1/4W 1.2K 1/4W 39K 1/4W 2.7K 1/4W 3.3K 1/4W 4.7K 1/4W 1.8K 1/4W 150K 1/4W 330K 1/4W 6.8K 1/4W 15K 1/4W 1.8K 1/4W 330
Pcs 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks ERJ2RHD513X
ERJ2RMJ394X ERJ2RMJ225X D0GA105JA001
ERJ2RMJ474X ERJ2RMJ474X ERJ2RMJ471X ERJ2RMJ682X ERJ2RMJ473X
ERJ2RMJ223X ERJ2RMJ334X
ERJ2RMJ102X ERJ2RMJ4R7X
ERJ2RMJ334X ERJ2RMJ473X
ERJ2RMJ471X
ERJ2RMJ393X ERJ2RMJ332X ERJ2RMJ472X
ERJ2RMJ334X ERJ2RMJ682X
ERJ2RMJ331X
Ref. No. R905 R911 R912 RX111 RX112 RX517,18 S1 S801 S802 S803-05 S806,07 S808 TH40 TH901 X101 X501 Z301
Part No. ERJ2GEJ102X D1H447320001 ERJ2GEJ6R8X D1H410420002 ERJ2GE0R00X ERJ2GE0R00X ABC1111P RSG0051-P ABC1112P RSG0051-P EVQP7L01K K0D112A00114 D4CC11030009 D4CC11030009 H0J169500011 H2D100500004 RJH9209-1 47K
Part Name & Description 1/4W 1K 1/4W 6.8 100K 1/4W 0 1/4W 0 SW,HEAD SW,PLAY SW,REC SW,STOP/FF/FR SW,VOL SW,HOLD THERMISTORS THERMISTORS OSCILLATOR OSCILLATOR TERMINAL
Pcs 1 1 1 1 1 2 1 1 1 3 2 1 1 1 1 1 1
Remarks ERJ2RMJ102X
D0YAR0000003 D0YAR0000003 K0L1BA000050 K0L1BA000051
K4BC02E00005
18. Cabinet Parts Location
19. Packaging
20. Schematic Diagram for printing with A4
H0211 TN/HH