Text preview for : SQ20_ET-SB-SI_1314768375.pdf part of Philips SQ20 ET-SB-SI 1314768375 Philips Audio LBB1229 SQ20_ET-SB-SI_1314768375.pdf



Back to : SQ20_ET-SB-SI_1314768375. | Home

Philips Communication & Security Systems
Supply Centre Breda
Customer Support
The Netherlands



COPYRIGHT (c) Philips Electronics N.V. 1994
Printed in the Netherlands
Supply Centre Breda SQ 20 Amplifiers




CONTENTS

CHAPTER DESCRIPTION PAGE

1 INTRODUCTION 3
1.1 GENERAL 3
1.2 THE SQ20 RANGE 3
2 TECHNICAL DATA 4
3 INSTALLATION INSTRUCTIONS 4
4 CHECKING AND ADJUSTING 5
5 CIRCUIT DESCRIPTION 6
5.1 DIFFERENCE BETWEEN THE SEVERAL OUTPUT-STAGE'S 6
6 SPARE PARTS 7
6.1 RECOMMENDED SPARE-PARTS TOTAL SQ 20 SERIES 8
6.2 SPARE-PARTS, LISTED PER TYPE-NUMBERS 9
6.2.1 LBB 1227/00 9
6.2.2 LBB 1228/00 9
6.2.3 LBB 1229/00 10
6.2.4 LBB 1230/00 11
6.2.5 LBB 1231/00 12
6.2.6 LBB 1232/00 13
6.2.7 LBB 1233/00 14
6.2.8 LBB 1234/00 15
6.2.9 LBB 1235/00 16
6.2.10 LBB 1236/00 17
6.2.11 LBB 1237/00 18
6.2.12 LBB 1238/00 19
6.2.13 LBB 1240/00 20




Service documentation 4822 733 24416 14 February 1994

-1-
SQ 20 Amplifiers Supply Centre Breda




CONTENTS (cont'd)
7 DRAWINGS
FIGURE: (as appendix)


7.1 LBB 1229/00 WIRING-DIAGRAM
7.2 LBB 1229/00 CIRCUIT-DIAGRAM PART 1
7.3 LBB 1229/00 CIRCUIT-DIAGRAM PART 2
7.4 LBB 1229/00 PRINTED CIRCUIT BOARD LAY-OUT

7.4.1 LBB 1230/00 CIRCUIT DIAGRAM PART 1
7.5 LBB 1230/00 CIRCUIT DIAGRAM PART 2
7.6 LBB 1230/00 PRINTED CIRCUIT BOARD LAY-OUT PART 1
7.7 LBB 1230/00 PRINTED CIRCUIT BOARD LAY-OUT PART 2

7.8 LBB 1231/00, -1232/00, -1233/00 CIRCUIT DIAGRAM PART 1
7.9 LBB 1231/00, -1232/00, -1233/00 CIRCUIT DIAGRAM PART 2
7.10 LBB 1231/00, LBB 1232/00, LBB 1233/00 PCB LAY-OUT PART 1
7.11 LBB 1231/00, LBB 1232/00, LBB 1233/00 PCB LAY-OUT PART 2

7.12 LBB 1234/00, LBB 1235/00 CIRCUIT DIAGRAM
7.13 LBB 1234/00, LBB 1235/00 PCB LAY-OUT

7.14 LBB 1237/00, LBB 1238/00 CIRCUIT DIAGRAM PART 1
7.15 LBB 1237/00, LBB 1238/00 CIRCUIT DIAGRAM PART 2
7.16 LBB 1237/00, LBB 1238/00 CIRCUIT DIAGRAM PART 3
7.17 LBB 1237/00, LBB 1238/00 CIRCUIT DIAGRAM PART 4
7.18 LBB 1237/00, LBB 1238/00 CIRCUIT DIAGRAM PART 5
7.19 LBB 1237/00, LBB 1238/00 PCB LAY-OUT PART 1
7.20 LBB 1237/00, LBB 1238/00 PCB LAY-OUT PART 2
7.21 LBB 1237/00, LBB 1238/00 PCB LAY-OUT PART 3

8. ADDITIONAL TYPE NUMBERS (SERVICE INFORMATION)

8.1 LBB 1227/00 UNIVERSAL PRE-AMPLIFIER
8.2 LBB 1228/00 CASSETTE UNIT
8.3 LBB 1236/00 SYSTEM PRE-AMPLIFIER
8.4 LBB 1240/00 240 W BOOSTER AMPLIFIER

9. GENERAL SERVICE INFORMATIONS




SERVICE DOCUMENTATION 4822 733 24416 14 February 1994

-2-
Supply Centre Breda SQ 20 Amplifiers




1 INTRODUCTION
l.l. GENERAL
The SQ20 range of high performance audio mixing, pre-mixing, booster and system amplifiers have been
designed for use in a wide variety of Public Address environments. Ease of operation, combined with good
service-accessibility have been optimised in their design.

1.2. THE SQ 20 RANGE
The SQ20 range consists of the following products:

LBB 1227/00 Universal Pre-Amplifier : SI 4822 861 05025
LBB 1228/00 Cassette Unit : SI 4822 861 05012
LBB 1229/00 Tuner-unit : SM 4822 733 24416
LBB 1230/00 Pre-Mixing Amplifier :: " "
LBB 1231/00 30 Watt Mixing Amplifier :: " "
LBB 1232/00 60 Watt Mixing Amplifier :: " "
LBB 1233/00 120 Watt Mixing Amplifier :: " "
LBB 1234/00 60 Watt Booster Amplifier :: " "
LBB 1235/00 120 Watt Booster Amplifier :: " "
LBB 1236/00 System Pre-Amplifier : SI 4822 861 05019
LBB 1237/00 60 Watt System Amplifier : SM 4822 733 24416
LBB 1238/00 120 Watt System Amplifier :: " "
LBB 1239/00 Mounting-brackets : " "
LBB 1240/00 240 Watt Booster Amplifier : SI 4822 861 05039

Note: SM -> Service manual
SI -> Service information

All relevant service information for the products can be found in the bulletins listed above. Not included
in this manual are the callstation(s) LBB 9427/10, LBB 9527/10 and LBB 9527/60. The LBB 9427/10,
and the new colour-item LBB 9527/10, are described within service manual: 4822 733 24437.
The LBB 9527/60 is described within a service information: 4822 861 05002.

This Service Manual is intended to provide all necessary information to carry out corrective maintenance
according to agreed policies. Spare parts are defined accordingly. In general this means repair on sub
assembly level. Component level repair can only be allowed where it can be carried out on a cost-effective
way.




Service documentation 4822 733 24416 14 February 1994

-3-
SQ 20 Amplifiers Supply Centre Breda




2 TECHNICAL DATA
Figure 2.1 upto and including 2.4 give all relevant data for SQ20 products.
For products for which service information is released through SI's this information can be found in
chapter 8.

3 INSTALLATION INSTRUCTIONS
- Opening the amplifier

Access can be gained to the inner side of the amplifier by removing the top cover.
Care should be taken not to lose the toothed washers which are fitted underneath the screws. For safety
reasons these washers are required to electrically bond the top cover to the earthed chassis of the amplifier.
And must therefore always be fitted.

Warning !: Before removing the cover, disconnect the amplifier from the mains supply by
removing the mains plug!

- 19" Rack Mounting

The range of SQ20 system amplifiers have been designed for both tabletop and 19" rack mounting. Two
mounting brackets (LBB 1239/00) can be ordered when rack mounting is required.

To attach the mounting brackets, first remove the top cover as described.
Locate the two screw holes provided for at both sides of the amplifier. Using the also added screws, firmly
mount the brackets to the amplifier.

CAUTION !: SQ20 amplifiers are not suitable for any surveillance application with e.g. 20kHz.

It is essential that the SQ 20 products are used within the specified temperature range.
The maximum permissible temperature is + 45