Text preview for : 800TFT.PDF part of Samsung 800TFT Samsung TFT-LCD MONITOR SyncMaster 800TFT - Service Manual



Back to : SAMSUNG_800TFT.zip | Home

COLOR MONITOR
SyncMaster 800TFT

SERVICE
COLOR MONITOR

Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignments & Adjustments 5. Troubleshooting 6. Exploded View & Parts List 7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams

Samsung Electronics Co., Ltd. September 1999 Printed in Korea Code No.: BN68-00049A

1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.

1-1 Safety Precautions
1-1-1 Warnings
1. 2. For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES (READING SHOULD NOT BE ABOVE 0.5mA)

1-1-2 Servicing the LCD Monitor
1. 2. When servicing the LCD Monitor, Disconnect the AC line cord from the AC outlet. It is essential that service technicians have an accurate voltage meter available at all times. Check the calibration of this meter periodically.

LEAKAGE CURRENT TESTER

2-WIRE CORD

1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. Inspect all protective devices such as nonmetallic control knobs; insulating materials; cabinet backs; adjustment and compartment covers or shields; isolation resistor-capacitor networks; mechanical insulators, etc. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 4.

*ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH GROUND

Figure 1-1. Leakage Current Test Circuit
With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

2.

3.

1-1-4 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part may create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

SyncMaster 800TFT

1-1

1 Precautions

1-2 Servicing Precautions
WARNING: Caution: Note: An electrolytic capacitor installed with the wrong polarity may explode. Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.

1-2-1 General Servicing Precautions
1. Always unplug the unit's AC power cord from the AC power source and disconnect the DC power jack before attempting to: (a) remove or reinstall any component or assembly. (b) disconnect PCB plugs or connectors. (c) connect a test component in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 6. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.

5.

2.

3.

1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD components are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor 6. Do not remove a replacement ESD from its components or assemblies, drain the electrostatic protective package until you are ready to install it. charge from your body by touching a known earth Most replacement ESDs are packaged with leads ground. Alternatively, wear a discharging wristthat are electrically shorted together by conductive strap device. To avoid a shock hazard, be sure to foam, aluminum foil or other conductive materials. remove the wrist strap before applying power to the monitor. 7. Immediately before removing the protective material from the leads of a replacement ESD, 2. After removing an ESD-equipped assembly, place it touch the protective material to the chassis or on a conductive surface such as aluminum foil to circuit assembly into which the device will be prevent accumulation of an electrostatic charge. installed. 3. Do not use freon-propelled chemicals. These can Caution: Be sure no power is applied to the generate electrical charges sufficient to damage chassis or circuit and observe all ESDs. 4. 5. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs.

other safety precautions.
8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-2

SyncMaster 800TFT

2 Product Specifications
2-1 Specifications
Item LCD Panel Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Maximum Pixel Clock rate Active Display Horizontal/Vertical Description TFT-LCD panel, RGB vertical stripe, normally white transmissive, 18-Inch viewable, 0.28 mm pixel pitch Horizontal : 30 kHz to 81 kHz (Automatic) Vertical : 56 Hz to 85 Hz (~XGA), 76 Hz (SXGA) 16.7 Million colors Horizontal : 1280 Pixels @ 81 kHz Vertical : 1024 Pixels @ 76 Hz Analog, 0.714 Vp-p ± 5% positive at 75 , internally terminated Type: Level: Seperate H/V sync, Composite H/V, Sync-on-Green TTL level (V high 2.0 V, V low 0.8 V), Sync-on-Green ( ­0.25 V)

135 MHz 359 ± 3 mm / 287.2 ± 3 mm

AC power voltage & Frequency AC 90 to 264 Volts, 60/50 Hz ± 3 Hz Power Consumption Dimensions Unit (W x D x H) Carton (W x D x H) Weight (Net/Gross) Environmental Considerations 42 W (max.), 40W (norminal)

17.7 x 18.2 x 7.2 Inches (449.4 x 461.2 x 182 mm) 22.4 x 11.6 x 22.8 Inches (570 x 295 x 580 mm) 8.3 kg (18.28 lbs) / 11.8 kg ( 20.0 lbs) Operating Temperature : 50°F to 104°F (10°C to 35°C) Humidity : 10 % to 80 % Storage Temperature : -68°F to 113°F (-20°C to 45°C) Humidity : 5 % to 95 %

· SyncMaster 800TFT complies with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. · Designs and specifications are subject to change without prior notice.

SyncMaster 800TFT

2-1

2 Product Specifications

2-2 Pin Assignments
Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 13W3 A1 A2 A3 4 4 A1-GND A2-GND A3-GND 3, 8 10 4 6 5 7 1, 2 15-Pin D-Sub & 13W3 Signal Cable Connector Separate Red Green Blue GND DDC Return (GND) GND-R GND-G GND-B No Connection Self Raster GND Bi-Dr Data (SDA) H-Sync V-Sync DDC Clock (SCL) Composite Red Green Blue GND DDC Return (GND) GND-R GND-G GND-B No Connection Self Raster GND Bi-Dr Data (SDA) H/V-Sync Not Used DDC Clock (SCL) Sync-on-green Red Green + H/V Sync Blue GND DDC Return (GND) GND-R GND-G GND-B No Connection Self Raster GND Bi-Dr Data (SDA) Not Used Not Used DDC Clock (SCL)

2-2

SyncMaster 800TFT

2 Product Specifications

2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode IBM
VGA2/ 70 Hz VGA3/ 60 Hz

VESA
640/75 Hz 640/85 Hz 800/75 Hz 800/85 Hz 1024/60Hz 1024/75Hz 1024/85Hz 1280/76Hz 1280/75Hz 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1024x768 1280x1024 1280x1024

Timing

720 x 400 640 x 480

fH (kHz) 31.469 A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Freq. (MHz) 31.777 3.813 1.589 26.058 0.318 70.087 14.268 0.064 0.858 13.155 0.191 28.322

31.469 31.778 3.813 1.589 26.058 0.318 59.940 16.683 0.064 0.794 15.761 0.064 25.175

37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500

43.269 23.111 1.556 2.222 17.778 1.556 85.008 11.764 0.671 0.578 11.093 0.023 49.500

46.875 21.333 1.616 3.232 16.162 0.323 75.000 13.333 0.064 0.448 12.800 0.021 49.500

53.674 18.631 1.138 2.702 14.222 0.569 85.061 11.756 0.056 0.503 11.179 0.019 56.250

48.363 20.677 2.092 2.462 15.754 0.369 60.004 16.666 0.124 0.600 15.880 0.062 75.000

60.023 16.660 1.219 2.235 13.003 0.203 75.029 13.328 0.050 0.466 12.795 0.017 78.750

68.677 14.561 1.016 2.201 10.836 0.508 84.997 11.765 0.044 0.524 11.183 0.015 94.500

81.129 16.640 6.400 2.880

79.976 12.504 1.067 1.837 9.481

3.200 76.106 10.660 0.080 3.200

0.119 75.025 13.329 0.038 0.475 12.804

0.020 135.000

0.013 135.000

Polarity H.Sync Negative Negative Negative Negative Positive V.Sync Positive Negative Negative Negative Positive

Positive Negative Positive Positive Negative Positive

Positive Negative Positive Negative Com.

Positive Positive Separate

Remark Separate Separate Separate Separate Separate Separate Separate Separate Separate Separate Sync
Horizontal
Video Video
CC

H/V Composite Sync
A Q Vertical P
RR S S

VIDEO R

S

Vertical
Video Video DD E E
Q

Horizontal B

O

Q

Sync-on-Green
Sync Sync B B AA Sync Sync

Vertical
PP
O O

Green Horizontal P B Q O R S

A : Line time total C : Back porch E : Front porch SyncMaster 800TFT

B : Horizontal sync width D : Active time

O : Frame time total Q : Back porch S : Front porch

P : Vertical sync width R : Active time

2-3

2 Product Specifications

Memo

2-4

SyncMaster 800TFT

3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 800TFT TFT-LCD monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components.

3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly. 2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

3-1-1 Removing the Stand
1. Remove 4 screws on the Stand.

7. Disconnect the Function PCB wire (10P) between the Function PCB and the CN102 connector on the Main PCB. 8. Disconnect 2 Inverter wires between the Panel and the CN2, CN3 connectors on the Inverter PCB. 9. Disconnect the 12P harness between CN1 connectors on the Inverter PCB and CN103 connector on the Main PCB. 10. Carefully lift the Main PCB Assembly and Inverter PCB and place them on a flat, level surface that is protected from static electricity. 11. Remove 10 screws on the PCB Bracket. 12. Remove the Bracket Assembly from the Front Cover. 13. Remove the 2 screws on the Function PCB from the Front Cover and remove the Function PCB and Function Knob.

3-1-2 Main Body Disassembly
1. Remove 4 screws on the Rear Cover. 2. Pull the Rear Cover up and off the monitor. 3. Remove 4 screws on the BRKT-VESA and Remove the BRKT-VESA. 4. Remove 16 screws on the PCB Shield and remove the Shield. 5. Remove 7 screws on the Main PCB and 2 screws on the Inverter PCB and 2 screws on the 10P Harness. 6. Disconnect the connector (140P) between the Panel and the CN600 connector on the Main PCB.

3-2 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.

SyncMaster 800TFT

3-1

3 Disassembly and Reassembly

Memo

3-2

SyncMaster 800TFT

4 Alignments and Adjustments
This section of the service manual explains how to use the DDC JIG to adjust the black, red, green, and blue levels of the FPD when you replace the AD Board, and how to update the microprocessor when you change the Panel or Lamp(s).

4-1 Required Equipment
The following equipment is necessary for adjusting the monitor: · Oscilloscope with probe tool · Computer with Windows 95 R , Windows 98 R , or Windows NT R . · DV18AS.exe software · DDC Control JIG

4-2 Using the DDC Control JIG
After replacing the LCD Panel, Lamp(s), and / or AD Board, use the DDC Control JIG to complete your service. Attach the DDC Control JIG to the flat panel display (FPD) as shown in the diagrams, below.

MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR PARALLEL CABLE PC SIGNAL GENERATOR SIGNAL CABLE

MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR SIGNAL CABLE PARALLEL CABLE PC D-SUB CONNECTOR 3-WIRE CABLE

3-WIRE CABLE

Figure 4-1. Setup 1, With Signal Generator Figure 4-2. Setup 2, Without Signal Generator

SyncMaster 800TFT

4-1

4 Alignments and Adjustments

4-2-1

Main Menu

4-2-2 Sub Menu
4-2-2 (a) Panel Information

4-2-1 (a) Service JIG : DV18

a

1

2

3

4

5

6

7

b c d e g

l

m

n h i j o

8

9
15

10

11

12

13

14 f

16

17

18

k

Figure 4-3.Service JIG Menu
No
1 2 3 4 5 6 7

Figure 4-4. Control JIG Menu
No
a

Label Red max value Green max value Blue max value Red min value Green min value Blue min value Color Auto Adjustment Red gain control Green gain control Blue gain control Red cutoff control Blue cutoff control Panel information Scroll bar

Definition Shows the red video signal max value Shows the green video signal max value Shows the blue video signal max value Shows the red video signal min value Shows the green video signal min value Shows the blue video signal min value Automatical screen contrast setting Adjusts the red video signal gain control Adjusts the green video signal gain control Adjusts the blue video signal gain control Adjusts the red video signal cutoff control Adjusts the blue video signal cutoff control Shows the sub menu to panel information (4-2-2 (a)) Changes the value or level of the selected item. The window to the right shows the value as it changes. Saves the current adjustment value of the R,G,B video contrast gain and cutoff level Displays and allows you to adjust the PC and Control JIG communication environment. Use this button to change the Delay parameter and Port Address of your PC system and to test the connection between the Control JIG and your computer Quits the DDC Control JIG

Label

Definition

Monitor On Time Total hours that the monitor has been actively functioning. Panel Cycle Time The total number of times the Panel has been turned ON. Total in Hours that this Panel or Lamp has been ON. Reset this number to 000000 after replacing the part. Total number of hours that this Panel has been ON. Total number of hours that this Upper Lamp has been ON. Total number of hours that this Lower Lamp has been ON. The number of times this Panel or Lamp has been replaced. The numbers are 00 if the item is the original factory part installed during manufacture of this monitor. Replacement times. This value is 00 if original equipment. Replacement times. This value is 00 if original equipment. Replacement times. This value is 00 if original equipment. Shows the message. Reads all Panel information data from the AD Board Writes the Panel Parameter Control values to the AD Board Reload the Panel Parameter Control values from the Program buffer Returns to the Main menu

b

c

d

Panel Lamp, Upper Lamp, Lower Change No.

8 9
10 11 12 13 14

e

f

Green cutoff control Adjusts the green video signal cutoff control

g

h

Panel Lamp, Upper Lamp, Lower Message Read Write Read buffer Return Main

15

i

16

SAVE

j

k l

17

Setting

m

n

18

Exit

o

4-2

SyncMaster 800TFT

4 Alignments and Adjustments

4-2-3 Adjustment Procedures
Use the following procedures whenever you replace the AD Board, Panel, or one or both of the Lamps. 4-2-3 (a) When Replacing the AD Board 1. Before replacing the AD Board, read all Panel information data by using the Read button on the DDC Control JIG. 2. Remove the old AD Board and replace it with a new board. 3. Perform the procedures described in section 4-2-3 (b). 4. Write the Panel information data to the new AD Board by using the Write button. 5. Perform other procedures using the DDC Control JIG, if necessary. 6. When all procedures are complete, select the Exit button ( 18 ) to quit the DDC Control JIG software. 4-2-3 (b) Color Auto Adjustment 1. After displaying 16-Gray pattern or black and white mixed pattern, click "Color Auto Adjustment" button. 2. During normal execution of Auto Algorithm the screen image may flicker. If Auto Algorithm does not excute properly, check DDC Control JIG. 3. After normal execution of Auto Algorithm, confirm optimal settings by observing the contrast of several different patterns on the display. 4. If you want to check each color value, click the button from 1 to 6 and from 8 to 13

4-2-3 (c) When Replacing the Panel 1. Select the Read Buffer button ( n ) to gather the current information about this monitor. 2. Increment the number by clicking on the (+) button on the Panel row in the Change No. column. If they were not already 00, the numbers for the Upper and Lower Lamps will automatically change to 00. 3. Check all values. If there is an error, select Read Buffer again and increment the Change No. column to the correct number. When all values are correct, select the Write button ( m ) to record the data in the firmware. 4. Select the Return Menu button ( Main Menu.
o

) to Return

4-2-3 (d) When Replacing the Upper and/or Lower Lamp 1. Select the Read Buffer button ( n ) to gather current information about this monitor. 2. Increment the number by clicking on the (+) button on the Lamp Upper and/or Lamp Lower row in the Change No. column. 3. Check all values. If there is an error, select Read Buffer again and increment the Change No. column to the correct number(s). When all values are correct, select the Write button ( m ) to record the data in the firmware. 4. Select the Return Menu button ( Main Menu.
o

) to Return

SyncMaster 800TFT

4-3

4 Alignments and Adjustments

4-3 Using the OSD Service function
After replacement of the LCD Panel or Lamp(s), use the 800TFT's OSD Service Function to complete your service. 1. To display the Service Function OSD, push and hold in for 8 seconds the Left and Right arrow buttons on the front panel of the monitor. 2. If the Panel has been replaced during this servicing, use the Up or Down arrow button on the front panel to highlight the Panel row on the table. Increment the Change No. value by pushing and holding in (for 8 seconds) the Left and Right arrow buttons on the front panel. Incrementing the Panel value automatically changes both the Upper and Lower Lamp Change No. value to 00. If you have changed the Upper and/or Lower Lamp(s) without changing the Panel, highlight the appropriate row(s) then push and hold in (for 5 seconds) both the Left and Right arrow buttons on the front panel. This action increments the Change No. value(s). Note: Increment the Lamp value(s) only if one or both of them were replaced, but the Lamp was not replaced. 3. After incrementing the appropriate values, power off the monitor.

Service Function Monitor On Time : 000049Hr Panel Cycle : 000088 Time Change No. Panel : 000050Hr 00 Lamp Upper : 000050Hr 00 Lamp Lower : 000050Hr 00
Figure 4-5. Service Function Menu Screen

4-4

SyncMaster 800TFT

4 Alignments and Adjustments

SyncMaster 800TFT

4-5

5 Troubleshooting
Notes: 1. Before troubleshooting, set up the PC's display as below. · Resolution: 1280 x 1024 · H-frequency: 64 kHz · V-frequency: 60 Hz 2. If no picture appears, confirm the power cord is correctly connected. 3. Check the following circuits. · No raster appears: Stand PCB, Main PCB · 14V develop but no screen: Main PCB · 14V does not develop: Main PCB 4. If you push and hold the EXIT button for more than 5 seconds, the monitor automatically reverts back to the factory preset

5-1 No Power

Does proper DC 14 V appear at DC jack connected to CN101? Yes Does proper DC 5 V appear at Pin 4 of IC101? Yes Does proper 5 V - signal appear at Pin 42 of IC501 (SW_REG_EN)? Yes Check Q103, Q105 and Q106.

No

Check Power Adaptor.

No

Check IC101 and related circuit.

No

Check IC501 and related circuit. (CN102, Function Key)

SyncMaster 800TFT

5-1

5 Troubleshooting

5-2 No Video
Check signal cable and connection.

Does the outpus signal appear at RA403 and R411 of IC406? (LDTGB, LVSYNCB, LHSYNCB, LCKBB) 1 2 3 4 Yes No Is the output of Pins 1, 17 of IC501 High ? No Check IC501 and related circuit Yes Check TFT-LCD panel and Inverter.

Does the analog video signal appear at R211, R212, R215? (BLUE, GREEN, RED) (IC201) Yes Does the sync signal appear at the output of Pin 14 of IC201and Pin 3 of IC 206 ? 5 6 (V-SYNC, H*V SYNC) Yes Does the input signal appear at the Pins 40, 41 of IC 300? 7 8 (PLL H*V MX-PDEN) Yes During power on-off does the input signal appear at the Pin 29,30 of IC300? (AD-SDA, AD-SCL) Yes Do the clock and sync signal appear at Pin 9 10 115, 117 of IC 300? (DCLKAB, MX_HSYNC) and does the digital video signal appear at thr output port PDA, PDB)? Yes During power on-off dose the input signal appear at the R 407 and R 408 ? (MX-SDA, MX-SCL) Yes Check IC 406 and related circuit.

No

Check IC201 and related circuit.

No

Check IC201, IC206 and related circuit.

No

Check the related circuit for these ports.

No

Check IC501 and related circuit.

No Check IC 300 and related circuit.

No

Check IC501 and related circuit.

5-2

SyncMaster 800TFT

5 Troubleshooting

WAVEFORMS
1 2 3 4

CH1 RMS = 3.26V

CH1 RMS = 3.25V

CH1 RMS = 3.12V

CH1 RMS = 2.20V

5

6

7

8

CH1 RMS = 4.96V

CH1 RMS = 4.42V

CH1 RMS = 3.20V

CH1 RMS = 3.24V

9

10

CH1 RMS = 2.50V

CH1 RMS =960mV

SyncMaster 800TFT

5-3

5 Troubleshooting

5-3 No OSD
WAVEFORMS
There is video but no OSD.
11

11 12 13

Does input signal appear at the Pins 2, 5 and 10 of IC404? Yes

No

Check IC405 and related circuit.
CH1 RMS = 4.18V

12

While pushing a front control button does any pulse appear at Pin 12 of IC404? Yes

No

Check IC404 and related circuit.

CH1 RMS = 3.26V

Replace IC404.
13

CH1 RMS = 3.26V

5-4

SyncMaster 800TFT

6 Exploded View and Parts List

SyncMaster 800TFT

6-1

6 Exploded View & Parts List

Memo

6-2

SyncMaster 800TFT

7 Electrical Parts List
7-1 Main PCB Parts
Loc. No. C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C130 C131 C132 C133 C134 C135 C136 C137 C138 C139 C140 C145 C146 C147 C201 C202 C203 C204 C205 C207 C208 C209 Code No. 2402-000176 2203-000257 2203-000257 2402-001044 2404-001075 2203-005005 2203-005005 2404-001075 2409-000124 2203-000257 2203-000257 2203-000257 2203-000257 2402-001044 2404-001075 2402-001042 2203-005005 2402-001042 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2404-000123 2402-001044 2203-000257 2203-005005 2203-005005 2402-000108 2203-000257 2203-000440 2402-000170 2402-001044 2203-000257 2402-000176 2203-000257 2402-000176 2203-001656 2402-000176 2203-000257 2203-000257 Description C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-ORGANIC C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-TA,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP Specification 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 100uF,20%,25V,TP,8.3x8.3x6.3 100uF,20%,16V,GP,TP,7343 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100uF,20%,16V,GP,TP,7343 100uF,10%,16V,LZ,BK,8x10.5 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 100uF,20%,25V,TP,8.3x8.3x6.3 100uF,20%,16V,GP,TP,7343 100uF,20%,16V,GP,TP,6.6x6.6x5. 100nF,15%,16V,W5R,TP,1608,1.6m 100uF,20%,16V,GP,TP,6.6x6.6x5 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,6032,2.9mm,TP 100uF,20%,25V,TP,8.3x8.3x6.3 10nF,10%,50V,X7R,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,WT,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 1nF,10%,50V,X7R,TP,1608 1uF,20%,50V,GP,4x5.4,1mm,TP 100uF,20%,25V,TP,8.3x8.3x6.3 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 470pF,5%,50V,CH,TP,1608,1.6mm 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 Remarks

SyncMaster 800TFT

7-1

7 Electrical Parts List

Loc. No. C210 C211 C213 C214 C217 C218 C219 C222 C223 C226 C230 C232 C233 C234 C235 C236 C238 C239 C240 C241 C242 C243 C244 C245 C246 C247 C248 C249 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319

Code No. 2404-000123 2203-005005 2402-000176 2203-000257 2402-000176 2203-000257 2402-000176 2203-000257 2402-000176 2203-005005 2203-005005 2203-001607 2203-000998 2203-001607 2203-005005 2203-001607 2203-001607 2203-000998 2203-001607 2203-001607 2203-001607 2402-000176 2203-001607 2402-000176 2203-000257 2203-000257 2402-000176 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005

Description C-TA,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP

Specification 10uF,20%,16V,6032,2.9mm,TP 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 220pF,5%,50V,CH,TP,1608,1.6mm 47pF,5%,50V,NPO,TP,1608 220pF,5%,50V,CH,TP,1608,1.6mm 100nF,15%,16V,W5R,TP,1608,1.6m 220pF,5%,50V,CH,TP,1608,1.6mm 220pF,5%,50V,CH,TP,1608,1.6mm 47pF,5%,50V,NPO,TP,1608 220pF,5%,50V,CH,TP,1608,1.6mm 220pF,5%,50V,CH,TP,1608,1.6mm 220pF,5%,50V,CH,TP,1608,1.6mm 10uF,20%,16V,GP,TP,4.3x4.3x5.4 220pF,5%,50V,CH,TP,1608,1.6mm 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m

Remarks

7-2

SyncMaster 800TFT

7 Electrical Parts List

Loc. No. C320 C321 C322 C323 C324 C325 C326 C327 C328 C329 C330 C332 C333 C334 C335 C354 C355 C356 C357 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C419 C420 C421 C422 C424 C425 C426 C427 C428 C429

Code No. 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-000257 2203-000257 2203-000257 2203-000257 2203-005005 2402-000176 2404-000123 2404-000123 2203-000384 2203-000384 2203-000384 2203-000257 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2404-000123 2203-000384 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2402-000176 2203-005005

Description C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-TA,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP

Specification 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10uF,20%,16V,6032,2.9mm,TP 10uF,20%,16V,6032,2.9mm,TP 15pF,5%,50V,NPO,TP,1608 15pF,5%,50V,NPO,TP,1608 15pF,5%,50V,NPO,TP,1608 10nF,10%,50V,X7R,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,6032,2.9mm,TP 15pF,5%,50V,NPO,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m

Remarks

SyncMaster 800TFT

7-3

7 Electrical Parts List

Loc. No. C430 C431 C432 C433 C434 C436 C437 C438 C439 C440 C441 C442 C443 C444 C445 C446 C448 C449 C450 C451 C452 C453 C454 C455 C456 C457 C458 C459 C460 C461 C501 C502 C503 C504 C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C516 C517 C600

Code No. 2203-000292 2404-000123 2203-005005 2203-005005 2203-005005 2203-000292 2203-000292 2203-000292 2203-000292 2203-005005 2402-000176 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-005005 2203-000626 2402-000176 2203-000626 2203-005005 2203-005005 2402-000176 2203-005005 2402-001042 2203-005005 2203-005005 2203-000292 2203-000257 2203-000257 2402-000176 2402-000176 2203-000626 2203-000626 2402-000176 2203-000257 2203-000236 2203-000236 2203-000257 2402-000176 2203-005005 2402-001042 2203-000491 2402-000176 2404-001075

Description C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-TA,CHIP

Specification 10pF,5%,50V,NPO,TP,1608 10uF,20%,16V,6032,2.9mm,TP 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10pF,5%,50V,NPO,TP,1608 10pF,5%,50V,NPO,TP,1608 10pF,5%,50V,NPO,TP,1608 10pF,5%,50V,NPO,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 22pF,5%,50V,NPO,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 22pF,5%,50V,NPO,TP,1608 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m 100uF,20%,16V,GP,TP,6.6x6.6x5. 100nF,15%,16V,W5R,TP,1608,1.6m 100nF,15%,16V,W5R,TP,1608,1.6m 10pF,5%,50V,NPO,TP,1608 10nF,10%,50V,X7R,TP,1608 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10uF,20%,16V,GP,TP,4.3x4.3x5.4 22pF,5%,50V,NPO,TP,1608 22pF,5%,50V,NPO,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 10nF,10%,50V,X7R,TP,1608 100pF,5%,50V,NPO,TP,1608 100pF,5%,50V,NPO,TP,1608 10nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100nF,15%,16V,W5R,TP,1608,1.6m 100uF,20%,16V,GP,TP,6.6x6.6x5. 2.2nF,10%,50V,X7R,TP,1608 10uF,20%,16V,GP,TP,4.3x4.3x5.4 100uF,20%,16V,GP,TP,7343

Remarks

7-4

SyncMaster 800TFT

7 Electrical Parts List

Loc. No. C601 C602 C625 C626 CA300 CA301 CA302 CA303 CA304 CA305 CA306 CA307 CA308 CA309 CA310 CA311 CA401 CA402 CA403 CA404 CA405 CA406 CA407 CA408 CA409 CA410 CA411 CA412 CN101 CN102 CN103 CN201 CN202 CN600 CN602 D3 D101 D102 D103 D104 D201 D202 D203 D204 D205 D206 D207

Code No. 2404-001075 2404-001075 2402-001042 2203-005005 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 2503-001018 3722-000117 3711-002050 3711-000556 3701-001129 3701-001142 3710-001508 3711-003942 0401-001056 0402-001098 0402-001098 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056

Description C-TA,CHIP C-TA,CHIP C-AL,SMD C-CERAMIC,CHIP C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK C-NETWORK JACK-DC POWER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-DSUB CONNECTOR-DSUB CONNECTOR-SOCKET CONNECTOR-HEADER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING

Specification 100uF,20%,16V,GP,TP,7343 100uF,20%,16V,GP,TP,7343 100uF,20%,16V,GP,TP,6.6x6.6x5. 100nF,15%,16V,W5R,TP,1608,1.6m 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 15PFX4,10%,50V 3P,3.5mm,AG,BLK,NO BOX,10P,1R,1.25mm,SMD-A,SN BOX,12P,1R,1.25mm,SMD-A,SN 15P,3R,FEMALE,ANGLE,AUF 10P+3P,2R+1R,FEMALE,ANGLE,AU15 140P,2R,0.8MM,SMD-S,AUF BOX,2P,1R,2mm,STRAIGHT,SN MMBD4148SE,75V,600mA,SOT-23,TP SK34,40V,3.0A,SMC,TP SK34,40V,3.0A,SMC,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP

Remarks

SyncMaster 800TFT

7-5

7 Electrical Parts List

Loc. No. D208 D209 D211 D212 D213 D214 D215 D216 D501 FT43 FT101 FT102 FT103 FT108 FT109 FT110 FT111 FT202 FT203 FT204 FT205 FT206 FT301 FT302 FT307 FT401 FT402 FT403 FT404 FT406 FT407 FT408 FT410 FT411 FT412 FT501 FT502 FT503 FT601 FT602 FT603 FT604 IC13 IC101 IC102 IC103 IC201

Code No. 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0401-001056 0403-000579 2901-001114 3301-001145 3301-001145 3301-001145 3301-001145 3301-001145 2901-001130 3301-001145 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2703-001070 2703-001070 2901-001133 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001133 2901-001114 2901-001114 2901-001114 3301-001145 3301-001145 3301-001145 3301-001145 1203-001801 1203-001448 1203-001447 1203-001649 1001-001082

Description DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-ZENER FILTER-EMI SMD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD FILTER-EMI SMD CORE-FERRITE BEAD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD INDUCTOR-SMD INDUCTOR-SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD IC-POSI.FIXED REG. IC-POSI.FIXED REG. IC-POSI.FIXED REG. IC-POSI.FIXED REG. IC-VIDEO SWITCH

Specification MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP BZX84C5V1,5.1V,5%,200mW,SOT-23 25VDC,2.0ADC,100nF,3.2x1.6x1 AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm 25V,4A,6.8nF,4.5x3.2x1.5,TP AB,4.5x1.6x1.6mm 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 25V,200mA,2x1.25x0.8,TP 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25V,200mA,2x1.25x0.8,TP 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm AB,4.5x1.6x1.6mm 3300,SOT-23,6P,70MIL,PLASTIC,3 2596,TO-263,5P,PLASTIC,4.750 2596,TO-263,5P,PLASTIC,3.135 BA12,TO-252,3P,PLASTIC,11.4/ BA7657F,SOP,24P,300MIL,SINGL

Remarks

7-6

SyncMaster 800TFT

7 Electrical Parts List

Loc. No. IC204 IC205 IC206 IC207 IC208 IC209 IC300 IC401 IC402 IC403 IC404 IC405 IC406 IC501 IC502 IC503 IC504 L101 L102 L103 L104 L105 L106 L107 L108 L109 L110 L111 L112 L113 L114 L115 L116 L117 L119 L120 L121 L122 L123 L124 L125 L126 L127 L129 L201 L202 L203

Code No. 0803-000106 0803-000106 0803-000122 0801-002171 0803-000117 0801-002404 1002-001171 1105-001165 1105-001165 1105-001165 BN09-00001A 0801-002237 1003-001243 0903-001063 1103-001164 1103-001163 1203-001109 2703-001778 2703-001778 2703-001778 BN27-20001C 2703-001778 2703-001778 BN27-20001A 2703-001778 2703-001334 2703-001334 2703-001778 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001778 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001070 2703-001070 2703-001070 2703-001334 2703-001334

Description IC-TTL IC-TTL IC-TTL IC-CMOS LOGIC IC-TTL IC-CMOS LOGIC IC-A/D CONVERTER IC-DRAM IC-DRAM IC-DRAM IC-OSD PROCESSOR IC-CMOS LOGIC IC-LCD CONTROLLER IC-MICROCONTROLLER IC-EEPROM IC-EEPROM IC-VOL. DETECTOR INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD COIL-SMD INDUCTOR-SMD INDUCTOR-SMD COIL-CHOKE INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD

Specification 74F132,TRIGGER,SOP,14P,150MIL, 74F132,TRIGGER,SOP,14P,150MIL, 74F125,BUFFER,SOP,14P,150MIL,Q 74LCX125,BUS BUFFER,SOP,14P,15 74F14,INVERTER,SOP,14P,150MIL, 74VHC4066,ANALOG SWITCH,SOP,14 AD9884,8BIT,QFP,128P,1/2LSB, 416S1020B,2x512Kx16BIT,SOP,50P 416S1020B,2x512Kx16BIT,SOP,50P 416S1020B,2x512Kx16BIT,SOP,50P LCD,MTV121P-31,16P 74HC04,INVERTER GATE,SOP,5P,49 MX88L282FC,QFP,256P,1102MIL,DU 72E75,8BIT,DIP,42P,600MIL,24MH 24LC21A,128X8BIT,SOP,8P,150MIL 24LC041,512X8BIT,SOP,8P,150MIL 7045,SOT-89,3P,PLASTIC,4.3/4 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 105UH,20%,SMD,TAPING 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 53.0UH,20%,DR10*5,TRAY 3.3UH,20%,3.2X2.5X2.2MM 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 3.3UH,20%,3.2X2.5X2.2MM 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 3.3UH,20%,3.2X2.5X2.2MM 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm

Remarks

SyncMaster 800TFT

7-7

7 Electrical Parts List

Loc. No. L204 L205 L206 L207 L401 L402 L600 L601 L602 L603 Q101 Q102 Q103 Q105 Q106 Q501 Q502 Q503 R101 R102 R103 R104 R105 R106 R107 R108 R114 R115 R116 R201 R202 R203 R204 R205 R206 R207 R208 R209 R211 R212 R214 R215 R216 R217 R218 R219 R224

Code No. 2703-001334 2703-001334 2703-001334 2703-001334 2703-001778 2703-001778 2703-001778 2703-001778 2703-001778 2703-001778 0505-001170 0501-002080 0501-002080 0501-002080 0505-001317 0501-002080 0501-002080 0501-002080 2007-000084 2007-000102 2007-000090 2007-000102 2007-000090 2007-000084 2007-000102 2007-000090 2007-000090 2007-000078 2007-000078 2007-000113 2007-000113 2007-001167 2007-000113 2007-001167 2007-000107 2007-001167 2007-000113 2007-001167 2007-001167 2007-001167 2007-000074 2007-001167 2007-000113 2007-001167 2007-000113 2007-001167 2007-000070

Description INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD FET-SILICON TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL FET-SILICON TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP

Specification 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM 3.3UH,20%,3.2X2.5X2.2MM SI9933ADY-T1,P20V,3.4A,0.075 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 FDC6326L,N/P,20V,1.8A,0.125OHM 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 4.7Kohm,5%,1/16W,DA,TP,1608 100Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 100Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 100Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 470Kohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 75ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608

Remarks

7-8

SyncMaster 800TFT

7 Electrical Parts List

Loc. No. R227 R229 R233 R234 R236 R237 R238 R240 R241 R242 R243 R246 R247 R249 R250 R252 R254 R255 R256 R257 R258 R259 R260 R261 R262 R263 R265 R267 R269 R301 R302 R303 R304 R305 R306 R307 R310 R311 R312 R313 R316 R317 R343 R348 R401 R402 R403

Code No. 2007-000116 2007-001114 2007-000070 2007-000070 2007-000070 2007-000074 2007-000074 2007-000118 2007-000070 2007-000118 2007-000070 2007-000070 2007-000118 2007-000118 2007-000070 2007-000070 2007-000070 2007-000074 2007-000080 2007-000080 2007-000090 2007-000090 2007-000074 2007-000074 2007-000070 2007-000070 2007-000113 2007-000070 2007-000070 2007-000239 2007-000118 2007-000118 2007-000071 2007-000071 2007-000071 2007-000090 2007-000071 2007-000071 2007-000080 2007-000080 2007-000090 2007-000090 2007-000090 2007-000070 2007-000074 2007-000090 2007-000074 R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP

Description

Specification 120ohm,5%,1/16W,DA,TP,1608 680Kohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 2Kohm,5%,1/16W,DA,TP,1608 2Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 33ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 1.5Kohm,1%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 390ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 2Kohm,5%,1/16W,DA,TP,1608 2Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 0ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608

Remarks

SyncMaster 800TFT

7-9

7 Electrical Parts List

Loc. No. R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R421 R422 R427 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R518 R519 R520 R521 R522 R523 R524 R525 R526 R527 R528

Code No. 2007-000071 2007-000084 2007-001002 2007-001002 2007-001002 2007-000084 2007-000084 2007-000071 2007-000084 2007-000084 2007-000084 2007-000074 2007-000074 2007-000074 2007-000074 2007-000071 2007-000109 2007-000074 2007-000071 2007-000090 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000084 2007-000084 2007-000084 2007-000084 2007-000078 2007-000074 2007-000074 2007-000074 2007-000084 2007-000074 2007-000084 2007-000084 2007-000084 2007-000084 2007-000074 2007-000075 2007-000074 2007-000076 2007-000075 R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP

Description

Specification 22ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 510ohm,5%,1/16W,DA,TP,1608 510ohm,5%,1/16W,DA,TP,1608 510ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 1Mohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 10Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 220ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 330ohm,5%,1/16W,DA,TP,1608 220ohm,5%,1/16W,DA,TP,1608

Remarks

7-10

SyncMaster 800TFT

7 Electrical Parts List

Loc. No. R529 R530 R531 R532 R533 R534 R535 R536 R537 R538 R539 R540 R541 R542 R543 R544 R545 R546 R547 R548 R549 R550 R551 R552 R553 R554 R555 R556 R557 R558 RA301 RA302 RA303 RA304 RA305 RA306 RA307 RA308 RA309 RA310 RA311 RA312 RA401 RA402 RA403 RA404 RA405

Code No. 2007-000074 2007-000076 2007-000078 2007-000074 2007-000074 2007-000077 2007-000078 2007-000074 2007-000074 2007-000074 2007-000074 2007-000092 2007-000092 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000109 2007-000075 2007-000078 2007-000077 2007-000074 2007-000084 2007-000084 2007-000074 2007-000074 2007-000071 2007-000102 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002

Description R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK

Specification 100ohm,5%,1/16W,DA,TP,1608 330ohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 470ohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 15Kohm,5%,1/16W,DA,TP,1608 15Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 1Mohm,5%,1/16W,DA,TP,1608 220ohm,5%,1/16W,DA,TP,1608 1Kohm,5%,1/16W,DA,TP,1608 470ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 4.7Kohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 100ohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,DA,TP,1608 100Kohm,5%,1/16W,DA,TP,1608 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST

Remarks

SyncMaster 800TFT

7-11

7 Electrical Parts List

Loc. No. RA406 RA407 RA408 RA409 RA410 RA411 RA412 RA413 RA414 RA415 RA416 RA417 RA418 RA419 RA420 RA421 RA422 RA423 RA424 RA425 RA427 RA429 RA430 U3 U6 U7 U8 U11 U12 X401 X501

Code No. 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 3301-001070 2402-001042 2203-005005 2901-001114 1204-001551 3301-001070 3301-001070 2801-003667 2801-003326

Description R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD C-AL,SMD C-CERAMIC,CHIP FILTER-EMI SMD IC-VIDEO SYSTEM CORE-FERRITE BEAD CORE-FERRITE BEAD CRYSTAL-SMD CRYSTAL-SMD

Specification 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST 22ohm,5%,1/16W,L,CHIP,8P,ST ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm 100uF,20%,16V,GP,TP,6.6x6.6x5. 100nF,15%,16V,W5R,TP,1608,1.6m 25VDC,2.0ADC,100nF,3.2x1.6x1 GS1881,SOIC,8P,150MIL,PLASTIC, ACA,3.2x1.6x0.9mm ACA,3.2x1.6x0.9mm 14.3182MHZ,50PPM,28-AAN,16,50O 24MHz,30ppm,28-ABX,16pF,50ohm

Remarks

7-12

SyncMaster 800TFT

7 Electrical Parts List

7-2 Sub PCB Parts
Loc. No. CN1 OP4 OP5 OP6 Q1 Q2 R1 R10 R11 R12 R13 R14 R2 R3 R4 R5 R6 R7 R8 R9 SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 Code No. 3711-004183 0601-001036 0601-001036 0601-001036 0501-000586 0501-000586 2001-000036 2001-000331 2001-000290 2001-000331 2001-000290 2001-000281 2001-000036 2001-000221 2001-000221 2001-000281 2001-000007 2001-000007 2001-000812 2001-000812 3404-000243 3404-000243 3404-000243 3404-000243 3404-000243 3404-000243 3404-000243 3404-000243 Description CONNECTOR-HEADER, LED, LED, LED, TR-SMALL SIGNAL, TR-SMALL SIGNAL, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, R-CARBON, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, SWITCH-TACT, Specification BOX,10P,1R,ANGLE,SN ROUND,GRN/YEL,4.75mm,565/585nm ROUND,GRN/YEL,4.75mm,565/585nm ROUND,GRN/YEL,4.75mm,565/585nm KSC945-Y,NPN,250mW,TO-92,TP,12 KSC945-Y,NPN,250mW,TO-92,TP,12 330ohm,5%,1/4W,AA,TP,2.4x6.4mm 12Kohm,5%,1/6W,AA,TP,1.8x3.2mm 10Kohm,5%,1/6W,AA,TP,1.8x3.2mm 12Kohm,5%,1/6W,AA,TP,1.8x3.2mm 10Kohm,5%,1/6W,AA,TP,1.8x3.2mm 100ohm,5%,1/6W,AA,TP,1.8x3.2mm 330ohm,5%,1/4W,AA,TP,2.4x6.4mm 1.2Kohm,5%,1/6W,AA,TP,1.8x3.2m 1.2Kohm,5%,1/6W,AA,TP,1.8x3.2m 100ohm,5%,1/6W,AA,TP,1.8x3.2mm 3Kohm,5%,1/6W,AA,TP,1.8x3.2mm 3Kohm,5%,1/6W,AA,TP,1.8x3.2mm 5.6Kohm,5%,1/6W,AA,TP,1.8x3.2m 5.6Kohm,5%,1/6W,AA,TP,1.8x3.2m 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S 15V,20mA,160gf+-50gf,6x3.4mm,S Remarks

SyncMaster 800TFT

7-13

7 Electrical Parts List

Others
Loc. No. LCD PROCESS-PBA UNIT S/CABLE P/CORD Code No. BN07-10001C BN94-00025A BN39-20001E BH39-10007A BH39-10339E BH39-10004A BH39-10339A BN44-00024A BN13-10001H Description LCD ASS'Y PCB CBF-SIGNAL CBF-POWER/CORD CBF-POWER/CORD CBF-POWER/CORD CBF-POWER/CORD Specification LQ181E1 DG01, 414*335*24,a-siTF DV18MSP DET,1830MM,15P/15P,IVORY,UL29 DET,RVV3,250V/10A,BLK,18 DET,RVV3,250V/10A,BLK,18 DET,RVV3,250V/10A,BLK,18 DET,RVV3,250V/10A,BLK,18 Remarks

EUROPE SEA,SESA KOREA UK
! !

ADAPTER INVERTER

7-14

SyncMaster 800TFT

SyncMaster 800TFT
DCLK dHsync
R_digital R_digital

8 Block Diagram

X-tal 14.3 Mhz

Video1

D'SUB
B_digital B_digital H_sync V_sync

R G B

ADC/ Pre-AMP/PLL (IC300)
Data Enable Dot CLK OSD Signal

G_digital

Scaling Engine (IC406)
TTL signal

G_digital

TFT LCD (Panel)

Video Switch (IC201)

Video2

13W3

V
OSD Control

H SOG H-Sync

Sync Separator (U8)

R/G/B

OSD (IC404)
I2C I2C

I2C

dVsync

MUX

Micro Control Unit
DC 12V DC 5V DC 3.3V

SDRAM (IC401, IC402, IC403)
X-tal (24Mhz)

User Control

DC 14V (Adapter)

DC_DC

8-1

8 Block Diagrams

Memo

8-2

SyncMaster 800TFT

SyncMaster 800TFT
CN1

9 Wiring Diagram

INVERTER

GND BL_CNT GND BL_ON GND GND +5V GND GND 14V_BL 14V_BL 14V_BL 10 11 12 1 2 3 4 5 6 7 8 9 1 GND 2 BL_CNT 3 GND 4 BL_ON 5 GND 6 GND 7 +5V 8 GND 9 GND 10 14V_BL 11 14V_BL 12 14V_BL

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

GND GND GND GND NC BBA NC BBA NC BBA NC BBA LCD +5V LCD +5V NC BBA NC BBA NC BBA NC BBA GND GND NC GBA NC GBA NC GBA

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

NC GBA LCD +5V LCD +5V NC GBA NC GBA NC GBA NC GBA GND GBA NC RBA NC RBA NC RBA NC RBA LCD +5V LCD +5V NC RBA NC RBA NC RBA

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

NC RBA GND GND LDTGB LDTGB LCD +5V LCD +5V LCKBB LCKBB GND GND NC BAA NC BAA NC BAA NC BAA LCD +5V LCD +5V NC BAA NC BAA NC BAA NC BAA

91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120

GND GND NC GAA NC GAA NC GAA NC GAA LCD +5V LCD +5V NC GAA NC GAA NC GAA NC GAA GND GND NC RAA NC RAA NC RAA NC RAA

121 LCD +5V 122 LCD +5V 123 NC 124 RAA 125 NC 126 RAA 127 NC 128 RAA 129 NC 130 RAA 131 GND 132 GND 133 T600 134 3.3V 135 GND 136 GND 137 12V 138 12V 139 12V 140 12V

CN103

CN600 (140P)

CN101 IN14V GND IN14V 1 2 3

MAIN PCB

RED & R_GND A1 GREEN&G_GND A2 BLUE & B_GND A3 DDC_CLK 1 CN202 DDC_CLK 2 NC 3 GND 4 5 H_SYNC 6 NC DDC_DATA 7 NC 8 9 V_SYNC SELF_TEST 10

CN201

KEY1 1 CN102 KEY2 2 LED_G 3 LED_R 4 GND 5 KEY +5V 6 +5V 7 GND 8 13W3_LED 9 D_SUB_LED 10 1 KEY1 2 KEY2 3 LED_G 4 LED_R 5 GND 6 KEY +5V 7 +5V 8 GND 9 13W3_LED 10 D_SUB_LED CN2

RED GREEN BLUE GND GND GND GND GND NC SELF_TEST GND DDC_DATA H_SYNC V_SYNC DDC_CLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Cable

13W3 CABLE

FUNC PCB

9-1

9 Wiring Diagram

Memo

9-2

SyncMaster 800TFT

10 Schematic Diagrams
10-1 Signal input Part Schematic Diagram

: power line : signal line

10-1

SyncMaster 800TFT

10 Schematic Diagrams

10-2 Scaler Chip Part Schematic Diagram
1 3

11

CH1 RMS = 3.26V

CH1 RMS = 3.12V

4

11

12

CH1 RMS = 2.20V

CH1 RMS = 4.18V

1 13 3

12

CH1 RMS = 3.26V

13

4

CH1 RMS = 3.26V

14

14
CH1 RMS = 4.7V

SyncMaster 800TFT

10-2

10 Schematic Diagrams

10-3 Power input Part & LCD panel interface part Schematic Diagram

10-3

SyncMaster 800TFT

10 Schematic Diagrams

10-4 Micom Part Schematic Diagram

SyncMaster 800TFT

10-4

10 Schematic Diagrams

10-5 A/D converter Part Schematic Diagram
7 8

CH1 RMS = 3.20V

CH1 RMS = 3.24V

9

10

CH1 RMS = 2.50V

CH1 RMS = 960mV

7 8

9 10

10-5

SyncMaster 800TFT